Hollyland Solidcom C1 Pro User manual

Hollyland Solidcom C1 Pro
User Manual
V2.0.0

EN-01
Introduction
Thank you for purchasing Hollyland Solidcom C1 Pro full-duplex wireless noise cancelling intercom
system.
The Solidcom C1 Pro, adopting the advanced DECT technology, is Hollyland’s first wireless self-
contained intercom system with Environmental Noise Cancellation (ENC). The system operates in the
1.9GHz band, providing a reliable LOS range of up to 1,100ft (350m).
This User Manual will help you through the installation and use of the equipment.

EN-02
Packing List
Solidcom C1 Pro - 2S 2-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate) x1
Remote Headset (With Blue Nameplate) x1
Charging Case x1
Battery x4
Microphone Cushion x2
Over-ear Leather Cushion x2
On-ear Foam Cushion x2
USB-A to USB-C Cable x1
Storage Case x1
User Manual x1
Warranty Card x1
Note: The quantity of the items depends on the product configuration.
(With Red Nameplate)
(With Blue Nameplate)

EN-03
Packing List
Solidcom C1 Pro - 3S 3-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate) x1
Remote Headset (With Blue Nameplate) x2
Charging Case x1
Battery x6
Microphone Cushion x3
Over-ear Leather Cushion x3
On-ear Foam Cushion x3
USB-A to USB-C Cable x1
Storage Case x1
User Manual x1
Warranty Card x1
Note: The quantity of the items depends on the product configuration.
(With Red Nameplate)
(With Blue Nameplate)

EN-04
Packing List
Solidcom C1 Pro - 4S 4-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate) x1
Remote Headset (With Blue Nameplate) x3
Charging Case x1
DC Adapter x1
Battery x8
Microphone Cushion x4
Over-ear Leather Cushion x4
On-ear Foam Cushion x4
USB-A to USB-C Cable x1
Storage Case x1
User Manual x1
Warranty Card x1
Note: The quantity of the items depends on the product configuration.
(With Red Nameplate)
(With Blue Nameplate)

EN-05
Packing List
Solidcom C1 Pro - 6S 6-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate) x1
Remote Headset (With Blue Nameplate) x5
Charging Case x1
DC Adapter x1
Battery x12
Microphone Cushion x6
Over-ear Leather Cushion x6
On-ear Foam Cushion x6
USB-A to USB-C Cable x1
Storage Case x1
User Manual x1
Warranty Card x1
Note: The quantity of the items depends on the product configuration.
(With Red Nameplate)
(With Blue Nameplate)

EN-06
Packing List
Solidcom C1 Pro - 8S 8-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate) x1
Remote Headset (With Blue Nameplate) x7
Charging Case x1
DC Adapter x1
Battery x16
Microphone Cushion x8
Over-ear Leather Cushion x8
On-ear Foam Cushion x8
USB-A to USB-C Cable x1
Storage Case x1
User Manual x1
Warranty Card x1
Note: The quantity of the items depends on the product configuration.
(With Red Nameplate)
(With Blue Nameplate)

EN-07
Operation Guide
Install the battery.
Step 1: Slide the battery
compartment cover lock.
Step 2: Open the cover. Step 3: Place the battery into the
compartment and close the cover.
Turn on the master headset and remote headsets.
Nameplate
Power Toggle
Master Headset Startup
1. Ensure that all the headsets are turned ON.
2. The indicator light stops flashing and stays
ON when the master headset is successfully
connected with the remote headsets.
3. Red nameplate: Master headset
Blue nameplate: Remote headset
Turn on the microphone.
Microphone Boom Rotation
Rotate the microphone boom upwards clockwise. Rotate the microphone boom upwards counterclockwise.
No RotationNo Rotation
ON ON
The Solidcom C1 Pro system is now ready for use.

EN-08
Pairing
The master headset is paired with the remote headsets at the factory. They are ready for use right
out of box. Manual pairing is only required when a new headset is added to the system. During the
pairing process, all the headsets must be turned ON and connected.
Pairing steps:
1. Press and hold the A button on both the master headset and remote headsets for 5 seconds.
Pairing is completed when the indicator light on each microphone boom stops flashing and stays
ON.
2. One master headset can be paired with up to 7 remote headsets.
Solidcom C1 Pro is highly versatile and can be applied in a variety of usage scenarios.
For more information about how to operate this system, please visit
https://hollyland-techhelp.zendesk.com/hc/en-us/categories/360005064994-Download

EN-09
Transmission Range 1,100ft (350m) LOS
Frequency Band 1.9 GHz (DECT) (varies by country and region)
Modulation Mode GFSK
TX Power ≤21dBm (125.9 mW)
RX Sensitivity <-90dBm
Battery Capacity 700mAh (2.66Wh)
Operation Time
Remote headset: >10 hours (when ENC is turned ON)
Master headset: >5 hours (when ENC is turned ON and the master
headset is connected with 5 remote headsets)
Master headset: >4 hours (when ENC is turned ON and the master
headset is connected with 7 remote headsets)
Charging Time About 2.5 hours
Frequency Response ENC OFF: 150Hz–7kHz (fluctuation range: ±6dB)
ENC ON: 150Hz–7kHz (fluctuation range: ±10dB)
Signal-to-Noise Ratio 71±2dB@94dBSPL, 1kHz
Distortion <1%@94dBSPL, 150Hz–7kHz
Microphone Type Electret
Input SPL >115dBSPL
Output SPL 94±3dBSPL (@94dBSPL, 1kHz)
ENC 20dB±2 with two microphones
(relative to environmental noise in all directions)
Net Weight About 170g (6oz) with batteries included
Temperature Range 0℃ to 45℃ (working condition)
–10℃ to 60℃ (storage condition)
Note: The frequency band and TX power vary by country and region.
Parameters

EN-10
Safety Precautions
Do not place the product near or inside heating devices (including but not limited to microwave
ovens, induction cookers, electric ovens, electric heaters, pressure cookers, water heaters, and gas
stoves) to prevent the battery from overheating and exploding.
Do not use non-original charging cases, cables, and batteries with the product.
The use of non-original spare parts may cause electric shock, fire, explosion, or other dangers.

EN-11
Support
If you encounter any problems in using the product or need any help, please contact Hollyland
Support Team via the following ways:
Hollyland User Group
HollylandTech
HollylandTech
HollylandTech
[email protected]
www.hollyland-tech.com

EN-12
Statement
All copyrights belong to Shenzhen Hollyland Technology Co., Ltd.
Trademark Statement
Without the written approval of Shenzhen Hollyland Technology Co., Ltd., no organization or
individual may copy or reproduce part or all of any written or illustrative content and disseminate it
in any form.
Note:
Due to product version upgrades or other reasons, this User Manual will be updated from time to
time. Unless otherwise agreed, this document is provided as a guide for use only. All representations,
information, and recommendations in this document do not constitute warranties of any kind,
express, or implied.

EN-13
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the device. This device complies with Part 15 of the FCC Rules.
Operations are subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operations.
FCC Radiation Exposure Statement:
The device has been tested and complies with FCC SAR limits.
Note:
This device has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This device generates, uses, and can radiate radio
frequency energy, and if it is not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this device does cause harmful intefrference to radio
or television reception, which can be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
烒 Reorient or relocate the receiving antenna.
烒 Increase the distance between the device and the receiver.
烒 Connect the device to an outlet on a circuit different from that to which the receiver is connected.
烒 Consult the dealer or an experienced radio/TV technician for help.