Holmes HASF-1710 User manual

THIS PRODUCT IS EQUIPPED WITH A POLARIZED
A.C. (Alternating Current) PLUG (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety fea-
ture. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit, con-
tact an electrician to replace the obsolete outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should always
be taken including the following:
• Use fan only for purposes described in the instruction manual.
• To protect against electrical shock do not immerse unit, plug or cord in
water or spray with liquids.
• Close supervision is necessary when any appliance is used by or near
children.
• Unplug from outlet when not in use, when moving fan from one loca-
tion to another, before putting on or taking off parts, and before
cleaning.
• Avoid contact with moving parts.
• Do not operate in the presence of explosive and/or flammable fumes.
• Do not place fan or any parts near an open flame, cooking or other
heating appliance.
• Do not operate any appliance with a damaged cord, plug, after the
appliance malfunctions, or has been dropped/ damaged in any man-
ner.
• The use of attachments not recommended or sold by the appliance
manufacturer may cause hazards.
• Do not use outdoors.
Do not let the cord hang over the edge of a table, counter, or come in con-
tact with hot surfaces.
• To disconnect, grip plug and pull from wall outlet. Never yank on cord.
• Always use on a dry, level surface.
• Do not operate without fan grills properly in place.
• This product is intended for household use ONLY and not for commer-
cial or industrial applications.
WARNING: To reduce the risk of fire or electrical shock, DO NOT USE THIS
FAN with any SOLID STATE Fan Speed Control Device
Three (3) Year Limited Warranty
SAVE THIS WARRANTY INFORMATION
A. The quality controls used in the manufacture of this Holmes©product
are to ensure your satisfaction.
B. This Warranty applies only to the original purchaser of this product.
C. This Warranty applies ONLY to repair or replacement of any supplied or
manufactured parts of this product that, upon inspection by Holmes
authorized personnel, proves to have failed in normal use due to
defects in material or workmanship. Holmes will determine whether to
repair or replace the unit. This Warranty does not apply to installation
expenses.
D. Operating this unit under conditions other than those recommended or
at voltages other than the voltage indicated on the unit, or attempting
to service or modify the unit, will render this WARRANTY VOID.
E. Unless otherwise proscribed by law, Holmes shall not be liable for any
personal injury, property or any incidental or consequential damages of
any kind (including water damage) resulting from malfunctions,
defects, misuse, improper installation or alteration of this product.
F. All parts of this Holmes product are guaranteed for a period of 3 year
as follows:
1. Within the first 30 days from date of purchase, the store from which
you purchased your Holmes product should replace this product if it
is defective in material or workmanship (provided the store has in-
stock replacement.)
2. Within the first thirty-six months from date of purchase, subject to
the conditions in paragraph H, Holmes will repair or replace the
product if it is defective in material or workmanship providing it is
returned to Holmes, freight prepaid, with PROOF OF PURCHASE date,
together with $6.00 for handling and return packing/shipping
charges.
returned to Holmes, freight prepaid, with PROOF OF PURCHASE date,
together with $6.00 for handling and return packing/shipping charges.
G. If you have any problem with this product, please write our Customer
Service Dept., or call, 1-800-5-HOLMES.
H. IMPORTANT RETURN INSTRUCTIONS Your warranty depends on your
following these instructions if you are returning the unit more than 30
days after the date of purchase:
1. Carefully pack the item in its original carton or other suitable box to
avoid damage in shipping.
2.Before packing your unit for return; be sure to enclose:
a) your name, full address with postal code and telephone number,
b) a dated sales receipt or PROOF OF PURCHASE,
c) your $6.00 check for return shipping and handling, and
d) the model number of the unit and the problem you are having.
(Enclose in an envelope and tape directly to the unit before the box is
sealed.)
3. Holmes recommends you ship the package via Royal Mail.
4. All shipping charges must be prepaid by you (as noted in paragraph F).
5. Ship to: HOLMES AIR CANADA INC.
P.O. BOX 279
PORT CREDIT, ON L5G 4L8
SHIPPING AND HANDLING CHARGES: $6.00
This warranty gives you specific legal rights, and you may have other
rights which vary from state to state. The provisions of this warranty are
in addition to, and not a modification of, or subtraction from, the statutory
warranties and other rights and remedies contained in any applicable
legislation. To the extent that any provision of this warranty is inconsistent
with any applicable law, such provision shall be deemed voided or
amended, as necessary, to comply with such law.
HASF-1710
Page1
HASF-1710-CSA-ENG-99-MN-01 Printed in China
Page 4
Owner’s Guide
☎INFO HOT-LINE: If, after reading this owner’s guide you have any questions or comments,
please call 1-800-5-HOLMES and a Customer Service Representative will be happy to assist you.
PLEASE READ AND SAVE THESE INSTRUCTIONS
16” OSCILLATING
METAL STAND FAN
ITEM # DESCRIPTION QUANTITY PRICE SUB TOTAL
MDB FanBonnet $8.99ea
for HASF-1710
Shipping and Handling
Applicable Provincal Taxes
GST
TOTAL
PLEASE USE THIS FORM TO ORDER-BY-MAIL.
A photocopy of this form will not be accepted
Method of Payment: ❏Cheque ❏ Money Order
SHIP TO: (PLEASE PRINT) PHONE#
STREET
CITY PROVINCE POSTAL CODE
To order, please send your cheque or money order, and this
completed form to: HOLMES, P.O. BOX 279, PORT CREDIT,
ONTARIO L5G 4L8
DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM
$2.00

THIS PRODUCT IS EQUIPPED WITH A POLARIZED
A.C. (Alternating Current) PLUG (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety fea-
ture. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit, con-
tact an electrician to replace the obsolete outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should always
be taken including the following:
• Use fan only for purposes described in the instruction manual.
• To protect against electrical shock do not immerse unit, plug or cord in
water or spray with liquids.
• Close supervision is necessary when any appliance is used by or near
children.
• Unplug from outlet when not in use, when moving fan from one loca-
tion to another, before putting on or taking off parts, and before
cleaning.
• Avoid contact with moving parts.
• Do not operate in the presence of explosive and/or flammable fumes.
• Do not place fan or any parts near an open flame, cooking or other
heating appliance.
• Do not operate any appliance with a damaged cord, plug, after the
appliance malfunctions, or has been dropped/ damaged in any man-
ner.
• The use of attachments not recommended or sold by the appliance
manufacturer may cause hazards.
• Do not use outdoors.
Do not let the cord hang over the edge of a table, counter, or come in con-
tact with hot surfaces.
• To disconnect, grip plug and pull from wall outlet. Never yank on cord.
• Always use on a dry, level surface.
• Do not operate without fan grills properly in place.
• This product is intended for household use ONLY and not for commer-
cial or industrial applications.
WARNING: To reduce the risk of fire or electrical shock, DO NOT USE THIS
FAN with any SOLID STATE Fan Speed Control Device
Three (3) Year Limited Warranty
SAVE THIS WARRANTY INFORMATION
A. The quality controls used in the manufacture of this Holmes©product
are to ensure your satisfaction.
B. This Warranty applies only to the original purchaser of this product.
C. This Warranty applies ONLY to repair or replacement of any supplied or
manufactured parts of this product that, upon inspection by Holmes
authorized personnel, proves to have failed in normal use due to
defects in material or workmanship. Holmes will determine whether to
repair or replace the unit. This Warranty does not apply to installation
expenses.
D. Operating this unit under conditions other than those recommended or
at voltages other than the voltage indicated on the unit, or attempting
to service or modify the unit, will render this WARRANTY VOID.
E. Unless otherwise proscribed by law, Holmes shall not be liable for any
personal injury, property or any incidental or consequential damages of
any kind (including water damage) resulting from malfunctions,
defects, misuse, improper installation or alteration of this product.
F. All parts of this Holmes product are guaranteed for a period of 3 year
as follows:
1. Within the first 30 days from date of purchase, the store from which
you purchased your Holmes product should replace this product if it
is defective in material or workmanship (provided the store has in-
stock replacement.)
2. Within the first thirty-six months from date of purchase, subject to
the conditions in paragraph H, Holmes will repair or replace the
product if it is defective in material or workmanship providing it is
returned to Holmes, freight prepaid, with PROOF OF PURCHASE date,
together with $6.00 for handling and return packing/shipping
charges.
returned to Holmes, freight prepaid, with PROOF OF PURCHASE date,
together with $6.00 for handling and return packing/shipping charges.
G. If you have any problem with this product, please write our Customer
Service Dept., or call, 1-800-5-HOLMES.
H. IMPORTANT RETURN INSTRUCTIONS Your warranty depends on your
following these instructions if you are returning the unit more than 30
days after the date of purchase:
1. Carefully pack the item in its original carton or other suitable box to
avoid damage in shipping.
2.Before packing your unit for return; be sure to enclose:
a) your name, full address with postal code and telephone number,
b) a dated sales receipt or PROOF OF PURCHASE,
c) your $6.00 check for return shipping and handling, and
d) the model number of the unit and the problem you are having.
(Enclose in an envelope and tape directly to the unit before the box is
sealed.)
3. Holmes recommends you ship the package via Royal Mail.
4. All shipping charges must be prepaid by you (as noted in paragraph F).
5. Ship to: HOLMES AIR CANADA INC.
P.O. BOX 279
PORT CREDIT, ON L5G 4L8
SHIPPING AND HANDLING CHARGES: $6.00
This warranty gives you specific legal rights, and you may have other
rights which vary from state to state. The provisions of this warranty are
in addition to, and not a modification of, or subtraction from, the statutory
warranties and other rights and remedies contained in any applicable
legislation. To the extent that any provision of this warranty is inconsistent
with any applicable law, such provision shall be deemed voided or
amended, as necessary, to comply with such law.
HASF-1710
Page1
HASF-1710-CSA-ENG-99-MN-01 Printed in China
Page 4
Owner’s Guide
☎INFO HOT-LINE: If, after reading this owner’s guide you have any questions or comments,
please call 1-800-5-HOLMES and a Customer Service Representative will be happy to assist you.
PLEASE READ AND SAVE THESE INSTRUCTIONS
16” OSCILLATING
METAL STAND FAN
ITEM # DESCRIPTION QUANTITY PRICE SUB TOTAL
MDB FanBonnet $8.99ea
for HASF-1710
Shipping and Handling
Applicable Provincal Taxes
GST
TOTAL
PLEASE USE THIS FORM TO ORDER-BY-MAIL.
A photocopy of this form will not be accepted
Method of Payment: ❏Cheque ❏ Money Order
SHIP TO: (PLEASE PRINT) PHONE#
STREET
CITY PROVINCE POSTAL CODE
To order, please send your cheque or money order, and this
completed form to: HOLMES, P.O. BOX 279, PORT CREDIT,
ONTARIO L5G 4L8
DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM
$2.00

Height Adjustment:
Follow these instructions to adjust the height of the fan.
STEP 1: Turn the pole locking knob counter-clockwise to loosen the pole.
STEP 2: Adjust the pole to the desired height, and firmly tighten the lock-
ing knob in a clockwise direction.
ADJUSTMENT INSTRUCTIONS:
Tilt Adjustment:
Follow these instructions to tilt the Fan Head for upward angle air move-
ment.
Step 1: To change the tilting angle of the fan head, simply loosen the Tilt
Adjustment Knob (see fig.4).
Step 2: Move the fan head to the desired angle, then firmly tighten the
knob to lock in place.
Height Adjustment:
Follow these instructions to adjust the height of the fan.
Step 1: Turn the extension pole base collar (see figure 3 and 5 on Page 2)
counter-clockwise to loosen pole.
Step 2: Adjust the pole to the desired height, and firmly tighten collar in a
clockwise direction.
CLEANING/MAINTENANCE INSTRUCTIONS:
Follow these instructions to correctly and safely care for your Holmes
Products© stand fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Be sure to use a soft cloth moistened with mild soap solution.
• Do not use any of the following as a cleaner: gasoline, thinner, or ben-
zine.
Fan Blade Cleaning:
(See instructions for fan head assembly on page 2, figure 4 )
STEP 1: To access the fan blade, remove the front grill and securing screw.
STEP 2: Clean the fan blade, front and rear grills with a soft, moist cloth.
STEP 3: Replace blade, tighten screw, and securely fasten the front grill.
Fan Head, Base, and Pole Cleaning:
Using a soft, moist cloth, with or without a mild, soap solution, carefully
clean the fan base, pole, and head. Please use caution around the motor
housing area. Do not allow the motor or other electrical components to be
exposed to water.
FAN STORAGE:
Your fan can be stored in the off-season either partially disassembled or
assembled. It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using the original (or appropri-
ately sized) box.
• If stored assembled or partially assembled, remember to protect the
fan head from dust.
The exclusive Holmes Products Fan Bonnet is available to protect your fan.
(See attached mail order form for special offer.)
For your own records, staple or attach your sales receipt to this manual.
Also, please take a moment to write the store name/location and date
purchased below.
STORE NAME
LOCATION:
DATE PURCHASED:
(STAPLE RECEIPT HERE)
Assembly Instructions:
Base/Pole Assembly:
You will need the base cover, weighted insert, pole, pole ring, and L-
shaped locking lever.
STEP 1:
Slide the bottom end of the pole through the pole ring.
STEP 2:
Turn the base cover upside down and place the weighted insert into the
base cover.
STEP 3:
Insert the threaded end of the locking lever into the hole of the weighted
insert and through the base cover.
STEP 4:
While holding the base cover and weighted insert with one hand, connect
the pole to the base, sliding the locking lever into the bottom of the pole
with your other hand.
STEP 5:
Turn the L-shaped locking lever clockwise to securely attach the pole to the
base.
STEP 6:
Set the base on the floor, weight side down. Push the pole ring down until
it sits directly on the base.
A)
Fan Head Assembly:
You are now ready to assemble the fan head.
STEP 1: Position the rear grill over the motor shaft, making certain the
notches at the top and bottom of the rear grill fit over the prongs
on the motor housing. Please make sure the rear grill fits securely
against the motor housing.
STEP 2: Secure the rear grill in its place using the rear grill mounting nut.
Turn this nut clockwise and tighten firmly.
STEP 3: Slide the fan blade, with the hollowed interior of the blade facing
toward the rear grill, firmly onto the motor shaft. The top of the
motor shaft should lie even with the center of the fan blade.
STEP 4: Now use the securing screw to lock the blade into place. Tighten
the screw into the side hole of the fan blade, against the motor
shaft, until both the blade and screw are secure.
STEP 5: Center the front grill by aligning the Holmes logo on the logo plate
so it is horizontal and parallel with the floor. Then, holding the
front grill against the rear grill, push the black grill ring into place
at the top and bottom of the fan. (Push directly on the black grill
ring, not on the grills themselves.) Finish securing the grill ring in
the same manner until both grills are joined underneath the black
ring.
Final Assembly:
First, slide the inner pole extension up from the outer pole. Insert the pole
locking knob into the hole on the outer pole, to securely hold this position.
Next, place the fan head assembly into this extension pole, inserting the
neck of the fan into the pole opening. Turn the fan head's neck until the
head is securely locked into place. Finally, add the tilt adjustment knob to
the hole of the fan head's neck. Tighten when fan head is in your desired
position.
OPERATING INSTRUCTIONS:
Step 1: Set fan base on a dry, level surface.
Step 2: Plug cord into any standard 120 volt AC outlet. Please make sure
the Selector (Speed) Control is in the Off position. Selector (Speed)
Control is located on the top of the Fan Motor Housing.
Step 3: The speed is adjusted by turning the control knob to the desired
setting, Off-High-Med-Low.
Step 4: The Oscillation Control knob is located on the top of the Fan Motor
Housing. To Start Oscillation, Push Control knob down. To Stop
Oscillation, Pull Control knob up.
Adjustment Instructions
Tilt Adjustment:
Follow these instruction to tilt the Fan Head for upward angle air move-
ment.
STEP 1:To change the tilting angle of the fan head, simply loosen the Tilt
Adjustment Knob.
STEP 2: Move the fan head to the desired angle, then firmly tighten the
knob to lock in place.
DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM
Fill out form on reverse side
to place your order today.
EXTEND THE LIFE OF
YOUR FAN
For short term or seasonal
storage of your Holmes fan
FAN
BONNET
$9.99
PLUS SHIPPING
AND HANDLING
Page2
H
Page 3
ABC
DEFGH
I
J
K
L
M
N
O
PQ
A) Front Grill
B) Fan Blade
C) Securing Screw
D) Mounting Nut
E) Black Grill Ring
F) Rear Grill
G) Motor Shaft
H) Motor Housing
I) Fan Head Neck
J) Tilt adjustment Knob
K) Inner Pole
L) Pole Lock Knob
M) Outer Pole
N) Pole Ring
O) Base
P) Round Weight
Q) L shaped locking lever

Height Adjustment:
Follow these instructions to adjust the height of the fan.
STEP 1: Turn the pole locking knob counter-clockwise to loosen the pole.
STEP 2: Adjust the pole to the desired height, and firmly tighten the lock-
ing knob in a clockwise direction.
ADJUSTMENT INSTRUCTIONS:
Tilt Adjustment:
Follow these instructions to tilt the Fan Head for upward angle air move-
ment.
Step 1: To change the tilting angle of the fan head, simply loosen the Tilt
Adjustment Knob (see fig.4).
Step 2: Move the fan head to the desired angle, then firmly tighten the
knob to lock in place.
Height Adjustment:
Follow these instructions to adjust the height of the fan.
Step 1: Turn the extension pole base collar (see figure 3 and 5 on Page 2)
counter-clockwise to loosen pole.
Step 2: Adjust the pole to the desired height, and firmly tighten collar in a
clockwise direction.
CLEANING/MAINTENANCE INSTRUCTIONS:
Follow these instructions to correctly and safely care for your Holmes
Products© stand fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Be sure to use a soft cloth moistened with mild soap solution.
• Do not use any of the following as a cleaner: gasoline, thinner, or ben-
zine.
Fan Blade Cleaning:
(See instructions for fan head assembly on page 2, figure 4 )
STEP 1: To access the fan blade, remove the front grill and securing screw.
STEP 2: Clean the fan blade, front and rear grills with a soft, moist cloth.
STEP 3: Replace blade, tighten screw, and securely fasten the front grill.
Fan Head, Base, and Pole Cleaning:
Using a soft, moist cloth, with or without a mild, soap solution, carefully
clean the fan base, pole, and head. Please use caution around the motor
housing area. Do not allow the motor or other electrical components to be
exposed to water.
FAN STORAGE:
Your fan can be stored in the off-season either partially disassembled or
assembled. It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using the original (or appropri-
ately sized) box.
• If stored assembled or partially assembled, remember to protect the
fan head from dust.
The exclusive Holmes Products Fan Bonnet is available to protect your fan.
(See attached mail order form for special offer.)
For your own records, staple or attach your sales receipt to this manual.
Also, please take a moment to write the store name/location and date
purchased below.
STORE NAME
LOCATION:
DATE PURCHASED:
(STAPLE RECEIPT HERE)
Assembly Instructions:
Base/Pole Assembly:
You will need the base cover, weighted insert, pole, pole ring, and L-
shaped locking lever.
STEP 1:
Slide the bottom end of the pole through the pole ring.
STEP 2:
Turn the base cover upside down and place the weighted insert into the
base cover.
STEP 3:
Insert the threaded end of the locking lever into the hole of the weighted
insert and through the base cover.
STEP 4:
While holding the base cover and weighted insert with one hand, connect
the pole to the base, sliding the locking lever into the bottom of the pole
with your other hand.
STEP 5:
Turn the L-shaped locking lever clockwise to securely attach the pole to the
base.
STEP 6:
Set the base on the floor, weight side down. Push the pole ring down until
it sits directly on the base.
A)
Fan Head Assembly:
You are now ready to assemble the fan head.
STEP 1: Position the rear grill over the motor shaft, making certain the
notches at the top and bottom of the rear grill fit over the prongs
on the motor housing. Please make sure the rear grill fits securely
against the motor housing.
STEP 2: Secure the rear grill in its place using the rear grill mounting nut.
Turn this nut clockwise and tighten firmly.
STEP 3: Slide the fan blade, with the hollowed interior of the blade facing
toward the rear grill, firmly onto the motor shaft. The top of the
motor shaft should lie even with the center of the fan blade.
STEP 4: Now use the securing screw to lock the blade into place. Tighten
the screw into the side hole of the fan blade, against the motor
shaft, until both the blade and screw are secure.
STEP 5: Center the front grill by aligning the Holmes logo on the logo plate
so it is horizontal and parallel with the floor. Then, holding the
front grill against the rear grill, push the black grill ring into place
at the top and bottom of the fan. (Push directly on the black grill
ring, not on the grills themselves.) Finish securing the grill ring in
the same manner until both grills are joined underneath the black
ring.
Final Assembly:
First, slide the inner pole extension up from the outer pole. Insert the pole
locking knob into the hole on the outer pole, to securely hold this position.
Next, place the fan head assembly into this extension pole, inserting the
neck of the fan into the pole opening. Turn the fan head's neck until the
head is securely locked into place. Finally, add the tilt adjustment knob to
the hole of the fan head's neck. Tighten when fan head is in your desired
position.
OPERATING INSTRUCTIONS:
Step 1: Set fan base on a dry, level surface.
Step 2: Plug cord into any standard 120 volt AC outlet. Please make sure
the Selector (Speed) Control is in the Off position. Selector (Speed)
Control is located on the top of the Fan Motor Housing.
Step 3: The speed is adjusted by turning the control knob to the desired
setting, Off-High-Med-Low.
Step 4: The Oscillation Control knob is located on the top of the Fan Motor
Housing. To Start Oscillation, Push Control knob down. To Stop
Oscillation, Pull Control knob up.
Adjustment Instructions
Tilt Adjustment:
Follow these instruction to tilt the Fan Head for upward angle air move-
ment.
STEP 1:To change the tilting angle of the fan head, simply loosen the Tilt
Adjustment Knob.
STEP 2: Move the fan head to the desired angle, then firmly tighten the
knob to lock in place.
DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM
Fill out form on reverse side
to place your order today.
EXTEND THE LIFE OF
YOUR FAN
For short term or seasonal
storage of your Holmes fan
FAN
BONNET
$9.99
PLUS SHIPPING
AND HANDLING
Page2 Page 3
ABC
DEFGH
I
J
K
L
M
N
O
PQ
A) Front Grill
B) Fan Blade
C) Securing Screw
D) Mounting Nut
E) Black Grill Ring
F) Rear Grill
G) Motor Shaft
H) Motor Housing
I) Fan Head Neck
J) Tilt adjustment Knob
K) Inner Pole
L) Pole Lock Knob
M) Outer Pole
N) Pole Ring
O) Base
P) Round Weight
Q) L shaped locking lever