Holz-Blech Spielberg 91809072-1 User manual

× 35
× 12
× 450
× 50
× 20
5×70
4×506×1401,4×40
M8×70
Ø 3 mm
Ø 4 mm
Ø 5 mm
Ø 8 mm
× 55
4×40
1/19
SHELTER 324×254
PREPARE THE GROUND, UNWRAP THE PACKAGE,
LAY OUT THE COMPONENTS, FIND THE TOOLS.

2/19
SHELTER 324×254
MAKE SURE THAT THE FOUNDATION
IS INSTALLED ON A LEVEL SURFACE.
CHECKING ALL DIRECTIONS,
INCLUDING CORNER TO CORNER. 3%
LAY OUT THE FOUNDATION BEAMS
AND SQUARE IT BY MEASURING
FROM CORNER TO CORNER.
IFB1
AC
DB
AB=CD
0°
IFB2

× 6
6×140Ø 5 mm
3/19
SHELTER 324×254
4%
ATTACH FOUNDATION BEAMS
WITH SCREWS.

BLG-1
ALG-1
× 6× 8
5×70
6×140
Ø 4 mm
Ø 5 mm
4/19
SHELTER 324×254
LAY OUT THE BOTTOM LOGS,
ATTACH TO THE FOUNDATION.
THE WALL LOGS WILL HANG OVER
THE FOUNDATION BEAMS BY
APPROXIMATELY 5MM. THIS OVERHANG
IS DESIGNED AS A RAIN DRIP. 7%
3 BL-1
6×140
2 BL-1
B LG-5
1 BL-1
5×70
5mm
A LG-5

× 12
6×140Ø 5 mm
5/19
SHELTER 324×254
9%
ATTACH THE FIRST ROW OF
WALL LOGS INTO THE BOTTOM
LOGS WITH SCREWS.
3 LG-1
2 LG-2
1 LG-1

6/19
SHELTER 324×254
16%
AFTER PLACING 3-4 ROWS OF WALL LOGS, TAP EACH
WALL LOG IN PLACE USING A HAMMER AND THE
HITBLOCK PROVIDED, TO TIGHTEN THE LOGS.
HITBLOCK
3 LG-2
2 LG-3
1 TL-1
A LG-4
B LG-4
3 LOGS IN PLACE

× 12
6×140Ø 5 mm
7/19
SHELTER 324×254
19%
INSTALL THE FLOOR BEAMS AND
ATTACH THEM WITH SCREWS.
FLB1

× 22
5×70Ø 4 mm
8/19
SHELTER 324×254
21%
INSTALL THE FLOOR BEAMS AND
ATTACH THEM WITH SCREWS.
FLB2
FLB3

9/19
SHELTER 324×254
30%
DON`T FORGET TO
TIGHTEN THE LOGS AFTER
EVERY 3-4 ROWS.
2 LG-1
2 LG-1
A LG-3
B LG-3

× 6
6×140Ø 5 mm
10/19
SHELTER 324×254
54%
INSTALL THE GABLES WITH LONG SCREWS
TO THE WALL LOGS ON THE FRONT AND
REAR WALLS.
14 LOGS IN PLACE
3 LG-3 3 TL-1
2 TL-1
2 LG-5
2 LG-4
A LG-2
A LG-1
B LG-2
B LG-1

× 14
6×140Ø 5 mm
11/19
SHELTER 324×254
58%
INSTALL THE ROOF PURLINS AND
ATTACH THEM WITH SCREWS.
RFB

× 231
4×50
12/19
SHELTER 324×254
PLACE THE FIRST ROOFBOARD FLUSH WITH
THE END OF THE PURLINS AND ATTACH
WITH 14 SCREWS, 7 INTO EACH NEXT,
SAW THE LAST BOARD TO MAKE IT FIT.
59%
RB

× 175
4×50
13/19
SHELTER 324×254
76%
14 SCREWS INTO THE FIRST
FLOORBOARD, 7 INTO EACH NEXT.
FB1

14/19
SHELTER 324×254
90%
SAW THE FLOORBOARDS
WHERE NEEDED.
FB2

× 2× 16
5×70
4×50
Ø 4 mm
Ø 3 mm
15/19
SHELTER 324×254
ATTACH FLOOR REINFORCEMENTS
INTO THE FLOORBOARDS AND FASCIA
TRIMS INTO THE ROOF PURLINS.
93%
FR
RF2 5×70
4×50

× 45
4×40Ø 3 mm
16/19
SHELTER 324×254
97%
EAVES EDGES GO ON TOP
OF THE ROOFING*.
*(NOT INCLUDED)
RF1
EE
FF2
FF1
FF2

× 20
1,4x40
17/19
SHELTER 324×254
98%
SAW THE BASEBOARDS
AND ATTACH WITH NAILS
AT EVERY 0,5 METERS.
BB

× 12
M8×70
Ø 8 mm
18/19
SHELTER 324×254
99%
DRILL THROUGH THE WALL, HOLE MUST
BE AT THE BOTTOM OF THE OVAL,
ATTACH WITH BOLT.
WINDBOARD

19/19
SHELTER 324×254
WHEN THE SLEEPING SHELTER IS ASSEMBLED,
YOU SHOULD COVER THE TIMBER WITH
WOOD PROTECTIVE SEAL, PAINT OR STAIN
AS SOON AS POSSIBLE TO AVOID DETERIORATION
TO THE WOOD.
100%