No Butts Bin SR1605 User manual

Assembly Instructions
Shelter type: SR1605
SR1605-01-120416-USA
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]

417
16
3 6
15
5
8
2
18
12
11
10
9
13
7
14
10
18
17
15
5
16
Tools required:
Drill/Screwdriver
Mallet
Hack saw
20
2
EXPLODED VIEW
Tools included:
Wrench
Torx bit

3
PARTS LIST
ITEM NO.
PART NO. DESCRIPTION
SIZE
IMAGE QUANTITY.
1 S1/HS FRAME
78
3
4
x 40
3
45
2
CB1 BRACKET
4
1
3
x 4
1
3
6
3
JF1
PLATE/
BRACKET
8
2
3
x 1
5
86
4
NBBS S1 STUB
5
6
8
x 1
5
8
x 1
5
82
5
RB2 BRACKET
4
1
3
x 1
7
88
6
JF2
PLATE/
BRACKET
5
1
8
x 1
1
44
7
R5
CURVED
RAFTER
85 x 1
5
8
x 1
5
81
8
R4
CURVED
RAFTER
85 x 1
5
8
x 1
5
83
9
L1 BRACKET
3
3
4
x 1
3
46
10
ST9 TIE BAR
611
2
x 1
5
8
x 1
5
82
11
JF3
PLATE/
BRACKET
8
1
4
x 1
6
82
12
P4 POST
78
3
41
13
SS SEALING STRIP
trim to 87
3
86
14
PCC2
ROOF
PANEL
87
3
8
x 40
1
21
15 PCE2
ROOF
PANEL
87
3
8
x 41
3
82
16
RC2
ROOF
STRIP
85
7
84
17
2MD
ROOF EDGE
TRIM
62 4
18
FT1 BRACKET
4
1
3
x 4
7
19 EC40 END CAPS
11
2
x 1
1
26
Fittings Bolt set M10
Nut Washer
Black
Cap
T25 T50 AB1210
3/8th x 2 3/8"
1" Tech
screw
2" Tech
screw
1/2 x 4"
Concrete Bolt
Pack A+B
40 40 80 80 136 66 13
Required 39 39 78 78 64 40 7
Spare
1 1 2 2 72 26 6
Image

124"
40 1
2
"
A
CB1
JF1
JF1
JF1
JF1
JF1
CB1
CB1
S1 STUB
S1 STUB
S1
S1
S1
S1
Check the
dimension
of the shelter to
ensure correct
alignment
GENERAL NOTE:
THE 2" TECH
SCREWS ARE
FOR FIXING ROOF
STRIPS
(RC) ONLY
CB1 CB1
JF1 JF1
S1 S1 S1
S1
S1
CB1
CB1
S1 STUB
S1 STUB
ENSURE CORRECT
ALIGNMENT ON
BOTH SIDES
DETAIL A (S1 STUB)
SCALE 1 : 5
S1 STUB
CB1
JF1
S1 FRAME
Step 1
Assemble S1 frames to make up the main structure using CB1 brackets
in the corners and JF1 brackets on the straight joints. Attach the S1 stub
as shown using JF1 brackets.
4

JF2JF2
JF2JF2
RB2
RB2
R5
R4
S1
CB1
JF1
JF2
S1 STUB DETAIL
Step 2
Attach R5 rafters using RB2 brackets on the back of the shelter and
JF2 brackets in the middle.
5

ST9
ST9
JF3
JF3
P4
RB2
RB2
Step 3
Assemble the T-frame using two ST9 tie bars and a P4 post. Join the two
ST9 bars together first using JF3 brackets, then attach the P4 post using
two RB2 brackets.
6

L1L1
L1L1
R4
R4
L1
L1
RB2
RB2
FT1
FT1
FT1
FT1
FT1
FT1
FT1
7
Step 4
Use L1 brackets to attach the T-bar to the front of the shelter and install
the R4 rafters using RB2 brackets on the rear and L1 brackets at the front.
Attach the FT1 brackets and move the shelter in to its final position
before using anchor bolts to secure it to the ground.

SSSS
SSSS
SSSS
PCE2
PCE2
PCC2
Step 5
Stick sealing strips (SS) to the rafters and align the PCE2 panels to the outside
of the shelter and centralise the PCC2 panel in the centre.
8

2MD
2MD
2MD
2MD
RC2
RC2
RC2
RC2
GENERAL NOTE:
THE 2" TECH SCREWS ARE
FOR FIXING ROOF STRIPS
(RC) ONLY
Step 6
Screw down the RC2 strips to secure the roof panels and clip on the
2MD edge trim to the bottom of the roof panels. Then fit the Black
plastic caps on exposed nuts and bolts. Fit the square end caps to any
open ends of box sections.
9

Notes:
10