No Butts Bin SR1558-F User manual

Assembly Instructions
Product Code:
SR1558-F
Doc. No.: SR1558-F-03-200319-USA

10 11
9
4
6
5
7
3
18
12
2
13
2
Exploded View
ITEM
NO. PART NAME
DRG NUMBER LENGTH
Exploded
View/QTY.
1 S1C Frame S1C
Default 5
2 JF1 Bracket JF1
Default 4
3 CB1 Bracket CB1
Default 7
4 ST1 Roof Tie ST1
Default 1
5 FT1 Bracket FT1
Default 2
6 FT3 Bracket FT3
Default 4
7 RB1 Bracket RB1
Default 8
8 R1 Rafter R1
Default 3
9 Sealing Strip SS
Default 4
10 ACE1 Roof Panel
Default 2
11 RC1 Roof Strip
Default 3
12 A1 Angle A1
Default 2
13 40x40 End cap BOUGHT IN ITEM
40 x 40 x
20 8

3
PARTS LIST
ITEM NO. PART NO. DESCRIPTION DIMENSION (mm) DIMENSION (Inch) IMAGE QTY.
1 S1C FRAME 2000x1035 78.74x40.75 5
2 JF1 BRACKET 220x40 7.87x1.58 3
3 CB1 BRACKET 110x110 4.33x4.33 7
4 ST1 ROOF TIE 1025x40x40 40.35x1.58x1.58 1
5 FT1 FOOT 109X100X40 4.29x3.94x1.58 2
6 FT3 FOOT 109X100X80 4.29x3.94x3.15 4
7 RB1 BRACKET 110x46 4.33x1.81 8
8 R1 RAFTER 1130x40x40 44.49x1.58x1.58 3
9 SS SEALING STRIP TRIM TO 1130 TRIM TO 44 1 ROLL
10 ACE1 ROOF PANEL 1130X1050 44.49x41.34 2
11 RC1 ROOF STRIP 1130 44.49 3
12 A1 ROOF EDGE 2100 x 50 x50 82.68 x 1.97 x 1.97 2
13 EC40
40x40 END
CAP
40X40 1.58x1.58 8

Tools required:
Drill/Screwdriver
Mallet
Hack saw
Spanner
Torx bit
4
Fittings and Tools
Fittings Bolt set M10 T25 BTANCM12100
M10 x 60 mm Nut Washer
Black
Caps
25 mm
Tech
screw
M10/12 x 100 mm
Concrete Bolt
Pack C
30 30 60 60 102 8
Required 12 12 24 56 24 6
Image

1075
1035
2110
40.75
83.07
42.32
IMPORTANT: Make sure side frames are aligned as detailed below.
CB1 BRACKET CB1 BRACKET
Aligned with inside
Aligned with outside
CB1
JF 1
S1C Frame
Step 1
Assemble the back and side frames using the S1C frames. Join the frames using
the CB1 brackets in the corners and the JF1 brackets on the flat joints.
5
Check the dimension
of the shelter to ensure
correct alignment.
BLUE DIMENSIONS - MM
GREEN DIMENSIONS - INCH

A
CB1
JF1
ST1
FT1
FT3
S1
CB1
JF1
ST1
S1C
DETAIL A
SCALE 1 : 4
JF1
ST1
Step 2
Insert EC40 end caps into both ends of the ST1 tie bar. Attach front S1C frame
and ST1 tie bar using CB1 brackets in the corners and JF1 brackets on the straight joint. Once
the main structure is secured, move the shelter into its final position and install foot brackets
FT1 and FT3 to fix shelter to the ground.
6

B
RB1
R1
E
Front View
RB1
R1 RAFTER
DETAIL B
SCALE 1 : 5
RB1
R1
995
39.17
1035 1035
40.75 40.75
DETAIL E - SCALE 1 : 12
Step 3
Screw RB1 brackets to the top of the frames, then Bolt R1 roof rafters to RB1
brackets. Rafters are 1035mm to centers (this should coincide with the next frame see
Detail E below).
7

RC1
SS
A1
ACE1
A1
SS
RC1
ACE1
Step 4
Stick sealing strips ( SS )on top of the rafters and align roof panels ( ACE1 ). Apply more
sealing strips to the top of the roof panel directly above the first sealing strips. Fix the RC1 strips
on the edges and over the gap between the roof panels and screw in with 25mm Tech
screws. Screw A1 Roof Angles alont the flat edges of the roof . Then fit the black plastic caps
on exposed nuts and bolts. Fit the square plastic end caps (EC40) to any open ends of box
sections.
8
NOTE:
SEALING STRIPS TO BE ATTACHED TO
RAFTERS AS SHOWN ON MODEL

995
1044.50
1044.50
1044.50
2115 OR 83.27
1035
2181 OR 85.87 HOLE CENTERS ON FEET
39.17
41.12
40.75
41.12
41.12
1144
45
Plan View
Suggested size for concrete base: 200mm OR 7.87inches oversized on all 4 sides.
9

NOTES:
10

NOTES:
11

12
CONTACT DETAILS:
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]
No Butts Bin Company, Inc. 16 Birch Lane, Madison, CT 06443
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fitting are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
All Parts and Fixings checked by:
Print Name: Signature: