Home Accents Holiday 1003144368 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.5 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the rpoduct to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for poper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product –not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of
the product when in use.
n) Read and follow all instructions that are on the product or provided with
the product.
o) SAVE THESE INSTRUCTIONS.
Pre-Assembly
Package Contents
Part
Description
Quantity
A
Tree top
1
B
Tree center
1
C
Tree bottom
1
D
Tree stand
1
E
Power Cord with Foot Pedal
Switch
1
7.5 ft Micro Dot LED Townsend Fir Color
Changing 9 Function Tree
SKU# 1003144368
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! –ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE
BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step 2. Insert the middle section (B) of the tree into the bottom section
(C). (See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig. 3)
Step 4. Connect the end connector of power cord with foot pedal switch (E)
with the connector found on the bottom section (C) in correct
direction (always match the protuberance on the end connector of
power cord to the concave on the connector found on the bottom
section (C) according to the magnified drawing. (See Fig. 4)
Assembly

Step 5. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 5)
Step 6. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the
main stem. Repeat pattern for each branch. (See Fig. 6)
Step 7. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
Step 8. Please note this tree comes with a foot pedal switch and a
remote control for easy illumination and changing functions.
This tree is Color Changing, the 9 lighting options available are:
1.Steady On
2.Steady Warm White
3.Flashing Warm White
4.Fade In and Fade Out Warm White
5. Steady Multicolor
6. Flashing Multicolor
7.Fade In and Fade Out Multicolor
8.Sequential Multicolor & Warm White
9.Color Changing
These functions can be changed by pressing the foot pedal
switch or using the remote control. Please see the instructions
of remote control below.
Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C) into
a proper outlet.
Step 2. Press the remote control or foot pedal switch to choose functions.
Instructions of Remote Control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press Fn button. Select from the following lighting functions:
Function 1: Steady On
Function 2: Steady Warm White
Function 3: Flashing Warm White
Function 4: Fade In and Fade Out Warm White
Function 5: Steady Multicolor
Function 6: Flashing Multicolor
Function 7: Fade In and Fade Out Multicolor
Function 8: Sequential Multicolor & Warm White
Function 9: Color Changing
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell “CR2025” (3 volt)
into the compartment.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree. Remove the power cords from the tree
bottom (C).
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well and the power cord is plugged into the hole
of the connector found on the tree bottom (C). Make
sure power cord plug is securely inserted into a
working electrical outlet.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Warning: Please note that changes or modifications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
UL Model No. TMH7.5-7N(0.5)
Operation