Home Accents Holiday 1005356557 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
c) This seasonal use product is not intended for permanent installation
or use.
d)Donotmountorplaceneargasorelectric heaters, fireplace,candles
or other similar sources of heat.
e)Do not secure the wiringof the product withstaples or nails, or place
on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
h) This is an electric product –not a toy! To avoid risk of fire, burns
personal injuryand electric shock itshould not beplayed with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j)Donothangornamentsorotherobjectsfromcord,wire,orlightstring.
k) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of
the product when in use.
m) This product is equipped with push-in type lamps. Do not twist
lamps.
n) This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation.If thefuse blows,unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
o) Do not move the tree by pulling the tree tips or tree branches.
p)Read and follow all instructions that are on the product or provided
with the product.
q) SAVE THESE INSTRUCTIONS.
Use and Care Instructions
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the
needles are brown or break off easily. Keep the tree holder filled
with water.
b) If the product is placed on a tree, the tree should be well secured
and stable.
c) Before using or reusing, inspect product carefully. Discard any
productsthathavecut,damaged,orfrayedwireinsulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
6.5' Winwood Grand Fir Potted Tree
SKU# 1005356557
d) When storing the product, carefully remove the product from
whereverit isplaced, includingtree, branches,orbushes, to avoid
anyunduestrainorstressontheproductconductors,connections,
and wires.
e) Whennot in use,store neatlyina cool, drylocationprotected from
sunlight.
Package Contents
A. Tree top
Qty: 1
B. Tree bottom
Qty: 1
C. Tree base
Qty: 1
D. Fuse
Qty: 6
E. Replacement
bulb
Qty: 6
F. Latch
Qty: 2
CAUTION! – ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE
BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step1. Carefully insert bottomsection(B)of tree intotreebase. (See
Fig. 1)
Step2.Insertthetopsection(A)intothebottomsection(B). (SeeFig.
2)
Step 3. Connect the plug of top section (A) with the end connector of the
bottom section (B) according to the magnified drawing. (See Fig.
3)
Step 4. Allowbranchestofall into placeor gently pullbranches upandout.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 4)
Pre-Assembly
Assembly

Step 5. Shape the branches. Starting with tips closest to the pole, shape
one tip tothe right, one to the left and oneat the center of the main
stem. Repeat pattern for each branch. (See Fig. 5)
Step 6. Plug the power cord from the bottom section (B) into a proper
outlet.
User Servicing Instructions
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover
on top of attachment plug towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided
with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a) Graspplugandremovefromthereceptacleorotheroutletdevice.
Do not unplug by pulling on cord.
b) Pull lamp and plastic base straight out of
lampholder.
c) Replace lamp with only 2.5 Volt,0.425 Watt
super bright type lamp (provided with
product).
If the lamp base of the replacement lamp does not fit in the string: (as
shown below bythe Figs.)
a) Remove the base of burnedout lamp by straightening lamp leads
and gently pull lamp out.
b) Thread leads of new lamp through holes in old
base with one lead in each hole.
c) Afterlampis fully insertedintobase,bendeachleadup, like other
lamps in the light set so that theleads will touch the contacts
inside the lampholder.
If connecting to a lighting stringthat does not have a Wattage (W)
rating {found on the tag within6 inches of the plug} calculate the
wattage as follows: Multiply thecurrent (0.34 A) which is on the
flag-type tag by 120.
For Example: Lighting string is rated 120V, 60Hz, 0.34 Amps.
0.34X120= 40.8 Watts
Add the wattage of each light string together for a total of 216 Watts or
less. (Do not exceed 216 Watts)
CAUTION:
1. To reduce the risk of overheating, replace burned-out lamps
promptly. Use 2.5 Volt, 0.425 Watt lamps only.
2. To reduce the risk of fire and electric shock:Do not install on trees
having needles, leaves or branch coverings of metal or materials
which look like metal, and do not mount or support strings in a
manner that can cut or damage wire insulation.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree.
Step 3. Gently lift the tree top straight up to remove from the bottom
section and fold all branches towards the pole.
Step 4. Carefullyplace alltreesectionsintoashippingbox andtapeitshut.
Step 5. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that connectors of all tree sections are
connected into each other well. Make sure power
cord plug is securely inserted into a working
electrical outlet.
Check for blown fuses at thepower cord plug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it with a
spare latch (F).
1) Place the branch into the slot of the bracket.
2) Insert a spare latch
through the hole and
use diagonal pliers (not
included) to crimp the
latch. (See Fig. A)
UL Model No. W-MF100/2(0.34A)