Home Styles 20 05170 0307 User manual

Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Drill (8 volts or less), 3/8” Drill Bit
Part List
Hardware List
Bracket
2 pcs.
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
20 05170 0307
Hutch
Cam Lock Screw
12 pcs.(+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
M4x13
Wood Screw for Bracket
8 pcs. (+1 extra)
Cam Lock
12 pcs.(+1 extra)
G.
Back Panel
3 pcs.
A.
Top
1 pc.
B.
Shelf
1 pc.
C.
Shelf
2 pcs.
D.
Side Panel
1 pc.
I.
Back Rail
1 pc.
F.
Back Upright
2 pcs.
E.
Side Panel
1 pc.
J.
Back Rail
1 pc.
H.
Divider
1 pc.
K.
Back Panel
1 pc.
M3.5x16
Wood Screw
9 pcs. (+1 extra)

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into
pre-drilled holes in Top (A), and
Side Panels (D), (E), then tighten.
(See Figure 1)
STEP 2
Attach Shelf (B) to Side Panel (D)
with Cam Locks. (See Figure 2)
Attach Back Rail (J) to unit with
Cam Lock.
Figure 2
A
D
E
D
B
J
Cam Lock Screw
Cam Lock Screw
Cam Lock
Cam Lock
Figure 1
Cam Lock Screw

Assembly Instructions 3/6
STEP 4
Attach Side Panel (E) to unit with Cam Locks.
STEP 3
Slide Back Panel (G) into place.
Attach Back Upright (F) to unit.
Slide Back Panel (G) into place.
Attach Back Upright (F) to unit.
Attach Back Rail (I) to unit with Cam Lock.
Slide Back Panel (G) into place.
F
E
G
F
I
G
G
Cam Lock
Cam Lock

STEP 6
Insert Adjustable Pins into
side panels at desired level.
Place Shelves (C) into position.
STEP 5
Slide Back Panel (K) into place.
Attach Divider (H) to unit.
Attach Top (A) to unit with Cam Locks.
C
C
K
H
A
Adjustable Pin
Cam Lock
Assembly Instructions 4/6

Assembly Instructions 5/6
STEP 7
Insert Wood Screws into pre-drilled holes
of unit, then tighten.
Wood Screw
STEP 8
Attach Hutch to Buffet with Brackets
by inserting Wood Screws for Bracket
into pre-drilled holes, then tighten.
(See Figure 3)
Wood Screw
for Bracket
Bracket
Figure 3

Assembly Instructions 6/6
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 4
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit
STEP 9
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
Pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 4)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.