Home Styles Bedford 88 5531 951 User manual

PART LIST
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5531 951
HARDWARE LIST
Casual Attire For Today's Home
Bedford
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
A.
Top
1 pc.
D.
Front Stretcher
1 pc.
F.
Back Stretcher
2 pcs.
G.
Back Piece
1 pc.
H.
Back Panel
2 pcs.
I.
Shelf
1 pc.
J.
Side Bar
2 pcs.
(
)
Drawers require assembly.
Please refer to the last page
of these assembly instructions.
L.
Door
1 pc.
M.
Door
1 pc.
N.
Drawer
1 pc.
Kitchen Cart
E.
Front Stretcher
1 pc.
Hex Wrench
1 pc.
Caster
two lock
two non-lock
4 pcs.
Small
Hex Wrench
1 pc.
Wood Screw
for Caster
16 pcs. (+1 extra)
Wood Screw (Long)
8 pcs. (+1 extra)
Wood Screw
6 pcs. (+1 extra)
Head Cap Bolt
4 pcs. (+1 extra)
Head Cap Bolt (long)
2 pcs. (+1 extra)
Cam Lock Screw
8 pcs.(+1 extra)
Cam Lock
8 pcs.(+1 extra)
Adjustable Pin
4 pcs. (+2 extra)
Machine Screw
for Side Bar
4 pcs.
Pull Handle
4 pcs.
Machine Screw
for Pull Handle
4 pcs.
K.
Base
1 pc.

Assembly Instructions 2/4
Cam Lock Screw
IMPORTANT
Do not tighten screws until each part is properly assembled.
You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
STEP 1
Put Cam Lock Screws into the pre-drilled holes of Side Panel (B),(C) and tighten.
Attach Back Stretcher (F) to
Side Panel (B) using Cam Locks.
Attach Back Piece (G) to the unit.
Slide Back Panels (H) into place then attach Back Stretcher (F) to unit.
Attach Front Stretcher (D) and (E) to Side Panel (B) using Cam Locks.
Attach Side Panel (C) to unit using Cam Locks.
STEP 2
C
B
D
E
B
C
F
F
G
H
H
Cam Lock

Assembly Instructions 3/4
STEP 3
Attach Base (K) to unit with
Head Cap Bolts (long).
Attach the four Castors to
the pre drilled holes of legs
as shown.
Figure 2
STEP 4
Figure 1
J
J
Attach Side Bar (J) to unit with Machine Screws.
(see Figure 1)
Place Top (A) onto the unit with Head Cap Bolts.
Attach Door (L) and (M) to
the side panel by sliding
the door lift hinges
into the side panel hinges. (see Figure 2)
Assemble Pull Handles to
Door (L) and (M) with
Machine Screws. (see Figure 3)
Insert Adjustable Pins into
side panels at the desired level.
Slide Shelf (I) into place.
Slide the Drawer (N) into position.
Machine Screw for Side Bar
K
Figure 3
LM
I
Head Cap Bolt (long)
Adjustable Pin
Locking Caster
Wood Screw
Head Cap Bolt A
N

Assembly Instructions 4/4
Part List
N1.
Front Part
1 pc.
N5.
Base Part
1 pc.
N2.
Back Part
1 pc.
N3.
Side Part
1 pc.
N4.
Side Part
1 pc.
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
N2
N2
N2
N3
N3
N3
N4
N4
N4
N5
N5
N1
N1
N1
Drawer (N)
Attach N1 to N3 and N4, using
a and
wood screws ,
tighten halfway.
Attach N2 to N3 and N4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screwdriver
(4X)
(4X)
long
long
Insert wood screws (6X)
into the pre-drilled holes in N5,
tighten screws. (see Figure 3)
short
Slide N5 into the grooves in N3
and N4. Be sure to push N5 all
the way forward so it meets N1.
(see Figure 2)
STEP 1
STEP 2
STEP 3 Tighten all screws used in
drawer assembly.
Figure 3
Figure 4
Attach hardware pulls with
machine screws.
(see Figure 4)
STEP 4