Home Styles 88 5001 004 User manual

88 5001 004
Buffet
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
IMPORTANT NOTE.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit Level,
(Please refer to the last page of these
instructions for drawer assembly steps.)
A.
Side Panel
1 Pc.
B.
Side Panel
1 Pc.
C.
Front Stretcher
1 Pc.
D.
Front Stretcher
1 Pc.
F.
Back Stretcher
1 Pc.
K.
Base
1 Pc.
E.
Front Upright
1 Pc. G.
Divider
1 Pc.
H.
Back Upright
1 Pc.
L.
Leg
2 Pcs.
I.
Back Stretcher
1 Pc.
J.
Back Panel
2 Pcs.
M.
Shelf
1 Pc.
P.
Drawer
M6x35
Head Cap Bolt
4 Pcs. (+1 extra)
Cam Lock
10 Pcs. (+2 extra)
Cam Lock Screw
10 Pcs. (+1 extra)
M3.5x13
Wood Screw (short)
for Base Drawer
8 Pcs. (+1 extra)
M3.5x16
Wood Screw
for Back Panel
8 Pcs. (+1 extra)
M4x25
Machine Screw
6 Pcs.
Small Hex Wrench
1 Pc.
M6x50
Head Cap Bolt (long)
4 Pcs. (+1 extra)
Cross Dowel
4 Pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Side Drawer
16 Pcs. (+1 extra)
Adjustable Pin
4 Pcs. (+2 extra)
Pull Handle
2 Pcs.
Knob
2 Pcs.
Hex Wrench
1 pc.
2 Pcs.
N.
Door
1 Pc.
O.
Door
1 Pc.

Assembly Instructions 2/5
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Back Stretcher (I).
Slide Back Panels (J) into place.
Attach unit from Step 3 to unit.
Attach Side Panels (A) and (B) to
unit with Cam Locks.
(See Figure 2)
A
A
B
B
G
F
H
C
D
E
J
J
I
Figure 1
Figure 2
Cam Lock Screw
Cam Lock
of Side Panels (A) and (B) and then tighten.

Assembly Instructions 3/5
Cross Dowel
Head Cap Bolt (long)
Cam Lock Screw
Wood Screw
for Back Panel
Head Cap Bolt
Cross Dowels and
Head Cap Bolts (long).
Attach Legs (L) to Base (K) with
Head Cap Bolts.
K
L
L
Figure 3
Figure 4 Figure 5 Figure 6
Note : Please make sure unit is level before tightening these screws.
Cam Lock
NO
M
PP
lift hinges. (See Figure 5)
To level the unit, adjust the adjustable levelers on the
bottom of unit (See gure 6)fi
Attach Door (N) and (O) to side panels by
sliding the door lift hinges into the side panel
Attach Top to unit with Cam Locks.
Insert Adjustable Pins into side panels at
the desired level.
Place Shelf (M) into position.
Attach Knobs to Door (N) and (O) with
Machine Screws. (See Figure 4)
Adjustable Pin

M3.5x13
Wood Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
M3.5x40
Wall Screw
1 pc.(+1 extra)
Assembly Instructions 4/5
Wood Screw
Wall Screw
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Top of unit
Drill 3/8” hole in wall

Assembly Instructions 5/5
Part List
Front Part
2 Pcs.
P2.
Back Part
2 Pcs.
P3.
Side Part
2 Pcs.
P4.
Side Part
2 Pcs.
P5.
Base Part
2 Pcs.
Figure 1
Figure 2
Figure 3
Figure 4
P1
P1 P2
P2
P5
P5
P3
P3
P4
P4
screwdriver and long Wood Screws (4X),
tighten halfway.
Attach P2 to P3 and P4 using long Wood
push P5 all the way forward so it meets P1.
(See Figure 2)
holes in P5, tighten screws.
(See Figure 4)
Tighten all screws used in drawer assembly.
Drawer
P1.
P1
P2
P3
P4

Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5001 102
Stainless Steel Top
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Care Instructions
This stainless steel top is made from high grade stainless steel on a strong wood
product base construction.
To avoid scratching the top during assembly, do not remove the top from this
carton until the body has been assembled and is ready for the top to be installed.
After removing the top from this carton place it on a soft cloth. ......................
This stainless steel top is ideal as a surface for food preparation but cannot be
used as a cutting or chopping board. Do not use knives or any sharp objects
directly on the top.
If scratched the following may improve the appearance of the top:
Apply talcum powder or flour on the scratched area and rub with very
fine steel wool in the same direction as the top’s hairline scratch pattern.
For assembly see instructions in carton 88 5001 Buffet carton.
Q.
Top
1 pc.