Home Styles Kitchen Center 88509995 C User manual

88509995 C
Kitchen Center
PART LIST
Casual Attire For Today's Home
Dear Our Valuable Customers,
Please follow our assembly instructions in every step,
we guarantee that you will get the perfect merchandise.
Thank you so much for purchasing our quality products.
Thai Patent Pending Numbers 086878
Tools Required For Assembly : Philips screwdriver
A.
Top
1 pc.
N.
Shelf
2 pcs.
D.
Middle Frame
1 pc.
C.
Side Panel
1 pc.
F.
Back Panel
3 pcs.
B.
Side Panel
1 pc.
I.
Front Rail
1 pc.
L.
Door
1 pc.
M.
Door
1 pc.
O.
Drawer
2 pcs.
S.
Side Rack
1 pc.
T.
Side Rack
1 pc.
V.
Brush Chrome Pipes
3 pcs.
W.
Handle Arm
2 pcs.
U.
Base Rack
1 pc.
(Knock-Down Construction, please refer
to the last page of these instructions for
steps to complete assembling drawers)
K.
Base
1 pc.
E.
Middle Frame
1 pc.
H.
Lower Back Stretcher
1 pc.
G.
Upper Back Stretcher
1 pc.
R.
Back Support
2 pcs.
Q.
Divider
1 pc.
X.
Round Arm
1 pc.
O.
Shelf
2 pcs.
P.
Drawer
2 pcs.
Caster
with and
without lock
4 pcs.
Head Cap Bolt
30 pcs. (+1Extra)
Hex Wrench
1 pc.
Machine Screw
for Pull Handle
6 pcs.
Adjustable Pin
16 pcs. (+1 Extra)
Wood Plug
7 pcs. (+2 Extra)
Pull Handle
2 pcs.
Pull Handle
2 pcs.
Wood Screw
for Bottom Drawer Part
(Short 6 x ½”)
12 pcs.(+1 Extra)
Wood Screw
for Side Drawer Part
(Long 6 x 1”)
16 pcs.(+1 Extra)
Wood Screw
16 pcs. (+ 1 Extra)
HARDWARE LIST
J1.
Back Post
1 pc.
J2.
Back Post
1 pc.

Assembly Instructions 2/5
STEP 1
IMPORTANT NOTE
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
STEP 2
Turn the unit in Step1 upside down.
Attach the Middle Frame (D) and (E)
to the unit. J
AA
E
B
C
F
A
G
H
I
J1
Head Cap Bolt F
F
D
Attach the Lower
Back Stretcher (H)
to the Side Frame (B),
using Head Cap Bolts.
Attach The Back Post (J1),(J2)
to the Lower Back Stretcher (H)
and slide the Back Panels (F) to place.
Attach the Upper Back Stretcher (G) to the assembled unit, using Head Cap Bolts.
Attach the Front Rail (I) to the Side Frame (B) with Head Cap Bolts.
Attach the Side Frame (C) to the assembled unit, tighten up all Head Cap Bolts.
Head Cap Bolt
J2

Assembly Instructions 3/5
STEP 3
STEP 4
STEP 5
Turn the assembled unit to back its
normal position.
Attach the Divider (Q) in the middle.
Attach the Back Support (R) to the
Upper Back Stretcher (G), using Head
Cap Bolts.
Attach the Handle Arm (W) to the
Side Panel (C) with Head Cap Bolts.
Slide the Round Arm (X) into place.
Place the Base (K) on the unit.
Tighten up all Head Cap Bolts.
R
A
X
W
Q
K
Attach 4 Casters to the underside of
the Base (K), put the 2 Casters with
lock in front as you first need to keep
the cart firmly in place. (See sticker in
the bottom indicating front side)
K
C
R
W
Wood Screw
Locking Caster
Head Cap Bolt
Head Cap Bolt
G

Assembly Instructions 4/5
STEP 6
STEP 7
Place the Top (A) on the unit.
Tighten up the Head Cap Bolts.
STEP 8
STEP 9
A
M
Insert the Adjustable Pins into the Side Panels
and into the Middle Frame at the desired level,
then put the Shelf (N) into the place.
Attach the Pull Handles to the Door (L)
and (M) with Machine Screws.
Attach the Door (L) and (M) to the
Side Panel by sliding the door lift hinges
into the side panel lift hinges.
See assembly instructions for Drawers in
the last page.
Slide the Drawers (P) into place.
Cover all holes with Wood Plugs. Lift hinge
Assembly
Pull Handle
Assembly
Adjustable Pin
A
A
L
N
N
OA
P
S
T
B
U
V
Attach the Side Rack (S) to the Side
Panel (B) with Head Cap Bolts.
Attach the Brush Chrome Pipes(V) and
the Base Rack (U) to the pre-drilled holes
of the Side Rack (S).
Attach the Side Rack (T) to the Side Panel (B).
O
Head Cap Bolt
Head Cap Bolt

A
P1
(Fig)1
MAKE SURE ROLLER
IS ON THE BACK
Assembly Instructions 5/5
Drawer
Unit Part List
P1.
Front Part
2 pcs.
P3.
Side Part
2 pcs.
P4.
Side Part
2 pcs.
P2.
Back Part
2 pcs.
(Fig) 4
(Fig)2
(Fig) 2
Turn the assembled drawer over and slide the
Plywood Bottom Part (O5) into the grooves
on Side Parts (O3) and (O4). Be sure to push
the plywood all the way forward so it meets the
Front Part (O1).
(Fig) 3
Insert the remaining (6) 1/2” screws
into the pre-drilled holes in Bottom Part
(O5), then tighten all screws
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.
(Fig) 1
Line up Side Parts (O3) and (O4) to the Front
Part (O1) and Back Part (O2). Be sure to
follow the Arrow sign sticker on the parts.
Using a Philips screw driver, insert 1” screws
into each of the 4 pre-drilled holes in sides
(O3) and (O4), then tighten half way.
P5.
Bottom Part
2 pcs.
A
P5
P4
P3
P2
A
P1
P3
P4
(Fig)3
A
P5
P3
P4 A
P1
P2
(Fig)4
Assemble the Pull Handles
with Machine Screws on
the Front Part (O1).