Home Styles 20 08000 0751 User manual

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Carton 20 08000 0752 is also needed for assembly.
20 08000 0751
IMPORTANT
Closet Wall Drawer Unit
Part List
Hardware List
Leveler
4 pcs.
Dowel (long)
4 pcs. (+1 extra)
Cam Lock (small)
18 pcs. (+2 extra)
M3 x.5 38
Wood Screw for
Bottom
4 pcs. (+1 extra)
Plastic Cap
8 pcs. (+1 extra)
E.
Side Panel
1 pc.
Cam Lock Screw
50 pcs. (+2 extra)
Adjustable Pin
12 pcs. (+1 extra)
Cam Lock Screw
(long)
6 pcs. (+1 extra)
Dowel
24 pcs. (+1 extra)
M3 x.5 25
Wood Screw
15 pcs. (+1 extra)
M3 x.5 64
Wood Screw (long)
10 pcs. (+1 extra)
Bracket
2 pcs.
C.
Side Panel
2 pcs.
D.
Side Panel
1 pc.
Cam Lock
44 pcs. (+6 extra)
M3 x.5 19
Wood Screw for
Leveler
16 pcs. (+1 extra)
Plug
4 pcs. (+1 extra)
Hex Wrench
1 pc.
M3 x1.5 5
Wood Screw for
Bracket
12 pcs. (+1 extra)
A.
Top
1 pc.
B.
Middle Panel
1 pc.
G.
Bottom
1 pc.
H.
Plinth
2 pcs.
J.
Front Rail
2 pcs.
I.
Plinth
2 pcs.

Assembly Instructions 2/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (C),
(D), (E), Bottom (G) and Plinths (H), then tighten. (See Figure 1)
Figure 1
A
Cam Lock Screw
C
Cam Lock Screw
C
Cam Lock Screw
D
E
Cam Lock Screw
G
H
Cam Lock Screw
H

Assembly Instructions 3/9
STEP 3
Attach Side Panels (D) and
(E) to Back Panel (F)
and Front Rails (J) with
Dowels and Cam Locks.
Attach Bottom (G) to unit
with Dowels, Cam Locks and
Wood Screws for Bottom. J
F
E
D
Wood Screw
for Bottom
Cam Lock
Figure 2
H
I
H
I
Cam Lock
STEP 2
PlinthAttach s (H) to Plinths (I) with
Cam Locks. (See Figure 2)
G
J
Dowel

Assembly Instructions 4/9
Leveler
STEP 5
Attach Levelers to bottom of unit with
Wood Screws for Leveler into
pre-drilled holes (See Figure 3).
Wood Screw for Leveler
Figure 3
Wood Screw (long)
Dowel
STEP 4
Attach unit from Step 2 to unit from Step 3
with Dowels and Wood Screws (long)
into pre-drilled holes.

Assembly Instructions 5/9
STEP 7
Attach Side Panels (C)
to Back Panel (F) with
Dowels and Cam Locks.
Attach Top (A) to unit with
Dowels and Cam Locks.
Cover Cam Locks with
Plastic Caps. (See Figure 4)
B
STEP 6
Turn unit over to it’s upright position.
Attach Middle Panel (B) to unit with
Dowels (long), Cam Lock Screws (long)
and Cam Locks.
Cam Lock
Dowel (long)
Cam Lock Screw (long)
Dowel
Cam Lock
F
C
C
A
Plastic Cap
Figure 4

Part List
Assembly Instructions 6/9
Drawer (L)
STEP 9
Slide Drawer Bottom (L5) into grooves in
Drawer Sides (L3) and (L4) until it meets
Drawer Back (L2).
Attach Support (L6) to unit with
Wood Screw.
L1.
Drawer Front
3 pcs.
L2.
Drawer Back
3 pcs.
L3.
Drawer Side
3 pcs.
L4.
Drawer Side
3 pcs.
L6.
Support
3 pcs.
STEP 10
Insert Cam Lock Screws
into pre-drilled holes in
Drawer Front (L1),
then tighten.
Attach Drawer Front (L1) to
drawer unit with Cam Locks (small).
STEP 8
Attach Drawer Sides (L3) and
(L4) to Drawer Back (L2) with
Wood Screws.
Cam Lock Screw
Cam Lock (small)
Wood Screw
Wood Screw
L2
L4
L3
L3
L4 L5
L1
L6
L5.
Drawer Bottom
3 pcs.
L4
L6 L5
L3
L2
L2

Assembly Instructions 7/9
Figure 5
Cam Lock
Plug
Adjustable Pin
K
STEP 11
Attach top unit to base unit
with Cam Locks.
Cover Cam Locks with
Plastic Caps.
K
L
K
L
L
Plastic Cap
Figure 6
STEP 12
Place unit at desired location.
Note: If assembling multiple Closet Wall Units together,
place all units at desired location.
Level unit(s) by adjusting the adjustable levelers on bottom of unit(s).
(See Figure 5)
Note: Unit(s) must be level to proceed.
Cover holes with Plugs. (See Figure 6)
Insert Adjustable Pins into side panels at desired level.
Place Shelves (K) into position.
Slide Drawers (L) into position.

Assembly Instructions 8/9
Hardware List
STEP 13
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
If assembling multiple Closet Wall Units
together, go to and complete Step 14 now,
then return to and complete Step 13.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3x16
Wood Screw
1 pc. (+1 extra)
Figure 7
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit
Pre-drilled hole
at top of unit
Bracket
2 pcs. (+1 extra)

Assembly Instructions 9/9
STEP 14
Note: If assembling multiple Closet Wall Units together, complete Step 14.
Attach tops of units together with Brackets and Wood Screws for Bracket into
pre-drilled holes. (See Figure 8)
Return to and complete Step 13.
Figure 8
Wood Screw for Bracket
Bracket

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at: