Home Styles 5580-97 User manual

5580-97
Bar Cabinet
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hardware List
Part List
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
A.
Base
1 pc.
E.
Shelf
1 pc.
I.
Adjustable Shelf
1 pc.
C.
Side Panel
1 pc.
G.
Middle Panel
1 pc.
D.
Side Panel
1 pc.
H.
Wine Rack
2 pcs.
B.
Leg
4 pcs.
F.
Top
1 pc.
J.
Door
1 pc.
K.
Door
1 pc.
L.
Back Panel
1 pc.
M.
Back Panel
1 pc.
Spring Washer (large)
4 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
M6x35
Head Cap Bolt
12 pcs. (+1 extra)
M8x50
Head Cap Bolt (large)
4 pcs. (+1 extra)
Flat Washer (large)
4 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.
M3x15
Wood Screw
24 pcs. (+1 extra)
M3x15
Tapered Wood Screw
8 pcs. (+1 extra)
Adjustable Pin
4 pcs. (+1 extra)
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

Assembly Instructions 2/8
Head Cap Bolt (large)
Spring Washer (large)
Flat Washer (large)
Head Cap Bolt
Spring Washer
Flat Washer
STEP 1
Place Base (A) upside down on a soft cloth.
Attach Legs (B) to Base (A) with Head Cap Bolts (large), Spring Washers (large) and
Flat Washers (large). (See Figure 1)
STEP 2
Attach Side Panels (C) and (D) to Shelf (E) with Head Cap Bolts,
Spring Washers and Flat Washers.
(See Figure 2)
Figure 1
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
A
BB
B
B
C
D
E
Figure 2

Assembly Instructions 3/8
STEP 3
Place Top (F) upside down on a soft cloth.
Attach unit from Step 2 to Top (F) with Head Cap Bolts,
Spring Washers and Flat Washers.
F
Head Cap Bolt
Spring Washer
Flat Washer

Assembly Instructions /48
STEP 4
Attach Middle Panel (G)
and Wine Racks (H) to unit.
Attach unit from Step1 to unit with Head Cap Bolts,
Spring Washers and Flat Washers.
Head Cap Bolt
Spring Washer
Flat Washer
G
HH

Assembly Instructions /58
I
STEP 5
Turn unit over to its upright position.
Insert Adjustable Pins into side panels at desired level.
(See Figure 3)
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 4)
Note: Unit must be level to work properly.
Adjustable Pin
Figure 3
Figure 4

Assembly Instructions /68
STEP 6
Attach Doors (J) and (K) to unit with Tapered Wood Screws.
(See Figure 5)
Tapered Wood Screw
Figure 5
K
J

STEP 10
Attach Back Panels (L) and (M) to unit with Wood Screws.
(See Figure 6)
Assembly Instructions /78
Wood Screw
L
M
Figure 6

Assembly Instructions /88
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit
STEP 11
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Figure 7
Hardware List
Anchor
1 pc.
Bracket
2 pcs.
Tipover Restraint
1 pc.
M3.5x40
Wall Screw
1 pc.
M3.5x16
Wood Screw
1 pc.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Wood Screw
Wall Screw Pre-drilled hole
at top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460