Homebase 3 SEATER SWING User manual

Powder-coated steel frame
H165 x W221.5 x D130cm
3 SEATER
SWING
INSTRUCTION MANUAL
IMPORTANT: Please read these instructions before using the product and retain for future use.
HHGL Limited, MK9 1BA. HHGL (ROI) Limited, D02 X576

2
SAFETY & CARE ADVICE
IMPORTANT INFORMATION
Please read these instructions fully before starting assembly.
• Check you have all the components and tools listed in this booklet before assembly.
• Remove all fittings from their plastic bags and separate them into their groups.
• Keep children and animals away from the work area; small parts could choke if swallowed.
• Make sure you have enough space to lay out the parts before starting.
• Do not stand or put weight on the component parts during assembly, as this could cause damage.
• Assemble on a soft, level surface to avoid damaging the unit or your floor.
• We recommend a two-person assembly.
• Dispose of all packaging carefully and responsibly.
• Regularly check all the bolts, screws and fastenings are secure.
• Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.

R u le
r- U s e th is ru le r to h e lp co rre ctl
y ide n tify th e s c re s
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
3
COMPONENTS - FITTINGS
Please check you have all fittings listed
below. If you have any missing or
damaged fittings, please contact your
local store.
Note: The quantities below are the correct
amount to complete the assembly. In some
cases, more fittings may be supplied than
required.
Tools included
Please check you have all components
listed below. If you have any missing or
damaged components, please contact
your local store.
COMPONENTS - PANELS
2 x Leg bases
2 x Front legs
2 x Rear legs
1 x Roof tube
1 x Seat &
backrest
2 x Roof bending
tubes
2 x Roof straight
tubes
2 x Armrest
tubes
2 x Rear
hanging tubes
2 x Front
hanging tubes
1 x Rear crossing
tube
1 x Middle
crossing tube
2 x Springs
1 x Roof fabric
2 x M8*90 Bolts
2 x M8*65 Bolts
2 x M8*40 Bolts
6 x M8 Locknuts
6 x M6 Locknuts
12 x M8 Flat washers
14 x M6 Flat washers
6 x M8 Bolt caps
8 x M6 Bolts caps
6 x M8 Nutcaps
6 x M6 Nutcaps
2 x M8 Screws
4 x M6*80 Bolts
4 x M6*55 Bolts
2 x M6 & M8
Spanners
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

ASSEMBLY INSTRUCTIONS
Step 1
Insert the front legs (2) and rear legs (3) into the tubes of the curved leg base (1) then loosely attach the roof tube (4) to the front and
rear leg tubes with M6 locknut (19) and the small flat washer (21) on one side, and bolt (28) and small flat washer (21) and a bolt cap
(23) on the other side using the Spanner (29).
Step 2
Loosely attach the middle crossing tube (12) to the curved leg base with bolts (28), small flat washers (21) and bolt caps (23).
Loosely attach the rear crossing tube (11) to the rear legs with bolts (27), small flat washers (21), bolt caps (23), M6 locknuts (19),
small flat washers (21) and nut caps (25) using the spanner (29).
Step 3
Loosely attach both armrest tubes (8) to seating and backrest panel (5) with M8 locknut (18), big flat washers (20), M8
nut caps (24), bolts (16), big flat washers (20) and bolt caps (22) using the spanner (29).
Loosely attach the upper front hanging tube (9) to the armrest with M8 locknut (18), big flat washers (20), M8 nut caps
(24), bolts (17), big flat washers (20) and bolt caps (22) using the spanner (29).
Loosely attach the upper rear hanging tube (10) to the armrest with bolts (15), big flat washers (20) and bolt caps (22).
Place the springs (13) through the hole connecting the front and rear hanging tube using the spanner (29).
21
19
1
2
421
23
28
3
11
12
25 19
21 21
27
23
21
28
23
9
8
13
10
5
24
18
20 22
17
20
24
18
20
16
22
20
20
22
15

ASSEMBLY INSTRUCTIONS
Step 4
Hang the assembled seat onto the hook on the roof tube.
Step 5
Assemble the roof fabric cover (14) over the roof tube (6 & 7), then connect the roof tube (6 & 7) together. Finally,
attach the assembled roof to the hanging swing with the adjustable screws (26) on both ends to fix it together
securely.
ASSEMBLY COMPLETE
6 7
14
6
26