Homebase ROWLY User manual

INSTRUCTION MANUAL
IMPORTANT: Please read these instructions before using the product and retain for future use.
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576
Power-coated steel frame
H170 x W182.5 x D121cm
ROWLY 3 SEATER
SWING SET

Domestic use only.
Maximum safe weight of use is 110kg (per seat).
We recommend that you cover your garden furniture when it's not in use and that it is stored in a garage or
shed throughout the winter months. Please ensure the furniture is dry before storing.
2
IMPORTANT INFORMATION
Regularly check all the bolts, screws and fastenings are secure.
Do not use this swing unless all bolts and screws are firmly secure.
Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
This product should not be discarded with household waste. Take it to your local authority waste disposal centre.
Keep children and animals away from the work area; amall parts could pose a choking hazard if swallowed.
Do not stand or put weight on the component parts or the product, as this could cause damage.
We do not recommend the use of power drills/drivers for inserting screws, as this could
Check you have all the components and tools listed on page 3.

3
TOP CROSS BEAM
W/ADJUSTABLE TEETH
REAR UPRIGHT SUPPORT
FRONT UPRIGHT SUPPORT
LATERAL CROSS BRACE
REAR CROSS BRACE
SWING ARM
SWING ARM TUBE
SUSPENSION SPRING
BOLT M6*60
SCREW ST4.2*16
WASHER d6.5*D16*1.2
WASHER d8.5*D17*1.6
PLASTIC SCREW
NUT WRENCH 13&17MM
HEX. KEY WRENCH 6MM
HEX. KEY WRENCH 4MM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
x 1
x 2
x 2
x 2
x 1
x 1
x 4
x 6
x 2
x 4
x 4
x 2
x 4
x 12
x 20
x 2
x 2
x 1
x 1
x 1
BOLT M6*45
BOLT M8*105
BOLT M6*75
x 2
x 2
BOLT M8*75
x 2
PLASTIC NUT M8*P1.25
x 6
PLASTIC NUT M6*P1.0
x 10
LEG CAP
SEAT ASSEMBLY
x 1
CANOPY
CANOPY/FRAME CONNECTOR
27 x 1
CUSHION
COMPONENTS
Please check you have all components listed below. If you have any missing or damaged components, please
contact your local store.

Step 3:
Fasten the lateral cross braces (4) to the
upright supports (2 and 3) by using bolts
(12), washers (18), and plastic nuts (20).
Repeat the same procedure for both sides.
See Fig. A – Step 3.
Step 5:
Insert the leg caps (10) into all of the base feet.
See Fig. A – Step 5.
Step 1
Step 2
Step 3
Step 4
Step 5
Fig. A
Step 1:
Fasten the front and rear upright supports (2
and 3) at the top by using bolts (11), washers
(17), and plastic nuts (19). Repeat the same
procedure for both sides. Keep the bolts loose.
See Fig. A – Step 1. Do not tighten the bolts
after step 1, fasten all of
the bolts after Fig A.
Step 2:
At both ends, insert the assembled upright
supports (2 and 3) into the top cross beam w/
adjustable teeth (1). Tighten all of the plastic
nuts and bolts now. See Fig. A – Step 2.
Step 4:
Fasten the rear cross brace (5) to the rear
upright supports (3) by using bolts (12),
washers (18), and plastic nuts (20). Tighten all
of the nuts and bolts. See Fig. A – Step 4.
11 17
17
17
17
11
12
18
18 20
12
10
10
10
10
18
18 20
2
2
2
3
2
3
3
3
3
3
3
2
23
2
4
5
4
3
1
NOTE: When fastening with nuts and bolts,
always use a washer (17 or 18) between the
tube and the bolt or the tube and the nut.
19
19
4

14
20
15
18
20
13
19
8
7
9
999
7 7 7
7
7
7
7 7 7 7
Fig. B
Fig. C
Step 6:
Open the seat assembly (8) and fasten a swing
arm tube (7) and a swing arm (6) to the seat
back by using bolt (14), washers (18), and
plastic nut (20). Repeat the same procedure for
both sides. Fasten another swing arm tube (7)
to the swing arm (6) at the front bend by using
bolt (15), washers (18), and plastic nut (20).
Repeat the same procedure for both sides.
Fasten the other end of the swing arm (6) to the
front of the seat assembly (8) by using bolt (13),
washers (17), and plastic nut (19). Repeat the
same procedure for both sides. See Fig. B.
Step 7:
Hook the suspension springs (9) into the
top of both swing arm tubes (7). Repeat the
same procedure for both sides. See Fig. C.
6
6
17
17
Warning:
Make sure that both ends of the suspension
springs (9) go completely through the holes
on the top cross beam w/adjustable teeth (1)
and the swing arm tubes (7).
Step 8:
Hang the opposite ends of the suspension
springs (9) into the holes located on the angled
braces of the top cross beam w/adjustable
teeth (1). Repeat the same procedure for both
sides. See Fig. D.
Fig. D
9
9
1
18
18
18
5

Step 10:
Fasten the canopy/frame connectors (21) on
the canopy assembly to the adjustable teeth
on both sides of the top cross beam (1) by
using plastic screws (22). See Fig. F.
Step 11:
Re-check and re-tighten all nuts and bolts to
assure stability.
Step 2
Fig. E
Fig. F
Step 9:
Slide the canopy/frame connectors (21) into
the canopy (26). Fasten them together by
using screws (16) in the pre-drilled holes.
Make sure that the teeth of the canopy/frame
connectors are facing toward the inside of the
frame. See Fig. E –Step 1 and Step 2.
1
Step 1
26
26
21
16
16
26
22
21
21
22
Step 12:
Place the cushion (27) onto the seat
assembly (8). See Fig. G.
Note:
To avoid danger of suffocation, please
always keep plastic bags or small parts away
from babies, children and pets.
Fig. G
27
6