Homebase 177/7772 User manual

Strand - 3 Door Centre Mirror Wardrobe
Dimensions
Width - 122.2cm
Depth - 53.6cm
Height - 196cm
Important – Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference 177/7772
267/5457
149/3719
BK03400 - Issue 1 - 11/06/2014
If you need help or have damaged or missing parts, call the Customer Helpline:
Homebase = 0345 0778888

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Due to difference in floor
levels, doors may not be
aligned. Adjustment may be
necessary.
• To prevent bowing of shelves
do not over load, and always
distribute weight evenly.
• If a residual aroma is
experienced with your new
furniture after the packaging
is removed simply ensure the
room is well ventilated and this
will assist a speedy removal
• We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• It is essential that this unit be
fixed to a wall with the fittings
provided.
• Please retain the product label
on the back of the unit, as this
information will help support any
queries.
• Dust with a clean cloth or, if
required a slightly damp cool
cloth. Do not use household
cleaners, abrasives or polishes
as permanent damage may
occur.
• Do not drag the furniture or lift
it by its top.
• Avoid sharp objects, contact
with water and direct heat on all
surfaces
• Your furniture is finished to the
required colour. Avoid exposure
to strong sunlight as this can
change the colour. Change in
appearence may also occur if
items are permanently left on a
surface.
• Doors should be secured or
removed before moving.
• You should get assistance
when moving or lifting your
furniture. Furniture consisting of
more than one unit should be
disassembled before attempting
to move it.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance - Non compliance with this information may affect your guarantee
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all boths and fittings are
tightened properly.

Components - Panels
Please check you have all the panels listed below
2
Cornice (122.2 x 5cm)
3
Double wardrobe (191 x 82.2 x 53.6cm)
1Single wardrobe (191 x 42.2 x 53.6cm)
2
If you have damaged or missing components, call the
Customer Helpline:
Homebase = 0345 0778888

3
Please check you have all the fittings listed below
Tools required
A
Wall strap x 1
E
20mm Cornice screw x 9
B
15mm Screw x 1
C
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
15mm Washer x 2
D
Components - Fittings
Phillips screwdriver
(medium)
Step ladder
(or equivalent)
The following components are pre-fitted and are illustrated for reference only.
Bar handle x 2
18mm Conecting bolt x 2
G
Threaded sleeve x 2
22mm Handle screw x 4
F
13mm Cornice screw x 2
Angle bracket x 2
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head to the point (30mm screw shown) .

4
Assembly Instructions
Step 1
Position and connect
the units
a: Before connecting the
units you will first need to
remove all doors.
Loosen but do not
remove bolt B in the
centre of the hinge back
plates which are attached
to the wardrobe side
panel.
Slide the door off the
back plates allowing bolt
B to go through the key
hole.
b: Position the double
wardrobe 1in the
required position [please
note it will be hard to
move once connected].
Once in place position
the single wardrobe 2
along side so the the
front edges are aligned.
To fix the two units
together you will need
two 18mm connecting
bolts Fand two
Threaded sleeves G.
Thread 18mm connecting
bolt Fthrough the
top hole inside the
double wardrobe then
screw threaded sleeve
Gthrough from inside
single wadrobe.
Repeat for bottom hole
A
A
B
C
F
G
a:
b:
1 2
WARNING: Help may be
required for this step.

5
Step 3
Remove and replace
handles
a: The bar handles are
fitted to the inside of
the unit, using a Philips
screwdriver unscrew the
22mm handle screws
in each handle and
remove both the 22mm
handle screw and the bar
handle.
Continued on next page.
22mm Handle screw
Assembly Instructions
Step 2
A
A
B
C
Re-fitting the doors
Starting from the top,
slide the keyhole shaped
groove in the hinge over
bolt B on the hinge plate.
Once located tighten bolt
B and move on to the
next hinge.
a:
1
2
Philips
screwdriver

Assembly Instructions
Step 4
Fitting the cornice
a: Place the cornice 3
on top of the wardrobe.
ensure the the back of
the cornice lines up with
the back of the pilaster
and that each end lines
up with the edge of the
pilaster.
When in position fix in
place using the 20mm
cornice screw Dthe
pre drilled hole in the
cornice 3and a philips
screwdriver.
Note: There are not any
pre-drilled holes in the
top of the robe for this.
Continued on next page.
6
Bar handle
22mm Handle screw
Step 3 - continued
b: Replace the bar
handle on the front of
the unit. Fix in position
by screwing the 22mm
handle screw into each
bar handle from inside
the unit using a Philips
screwdriver.
Note: Only use the
20mm handle screw that
the handles were pre-
fitted with.
b:
a:
1
2
Philips screwdriver
1
2
D
Philips screwdriver
Pilaster
3

Assembly Instructions
Step 4 - continued
Step 5
A
Using the correct type of screw
screw through the washer and wall
strap into a pre-drilled hole in the
wall
C
B
B
7
Fixing to wall
It is recommended that
the wardrobe is fixed to
a wall
Fix wall strap Cto the
top of wardrobe using
15mm screw Aand
15mm washer B.
Warning: The
15mm screw A
is for fixing the
wall strap Cto furniture
only. In addition to this
you will need to choose
a screw or fitting which is
suitable for securing the
wall strap Cto the type
of walls you have. If you
are unsure about what
type of screw to use seek
professional help.
12
b: When fixed in place
fully secure by screwing
the13mm cornice
screws Ethrough the
angle brackets in to the
wardrobe using a philips
screwdriver.
Note: There are not any
pre-drilled holes in the
top of the robe for this.
b:
Angle bracket
3

Step 6
A
A
B
C
1
3
Adjusting doors
1. To adjust the height /
level of the door loosen
all screw ‘A’s on all hinge
plates, level the door
height and retighten all
screw ‘A’s.
2. To adjust the gap
between the doors
loosen screw ‘B’, then
turn screw ‘C’ clockwise
to close the gap or
anticlockwise to increase
the gap. Re-tighten
screw ‘B’ to lock position.
3. To adjust the distance
away from the unit
loosen screw ‘B’, this
allows the hinge arm
to slide back and forth.
Adjust as required then
re-tighten screw ‘B’.
Assembly is complete.
Assembly Instructions
2
If you need help or have damaged or missing parts, call the Customer Helpline:
Homebase = 0345 0778888