Homebase ANDORRA ROCKING TEA FOR TWO User manual

INSTRUCTION MANUAL
IMPORTANT: Please read these instructions before using the product. Retain instructions for future use.
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576
ANDORRA ROCKING
TEA FOR TWO
Power-coated steel frame
Toughened glass table top
Chairs: H85.5 x W66 x D85.5cm
Table: H46 x Dia. 46cm

Domestic use only.
Maximum safe weight of use is 45kg.
We recommend that you cover your garden furniture when it's not in use, and that it is stored in a garage
or shed throughout the winter months. Please ensure the furniture is dry before storing.
2
IMPORTANT INFORMATION
Regularly check all the bolts, screws and fastenings are secure.
Do not use this table unless all bolts and screws are firmly secure.
Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
This product should not be discarded with household waste. Take it to your local authority waste disposal centre.
Keep children and animals away from the work area; small parts could pose a choking hazard, if swallowed.
Do not stand or put weight on the component parts or the product, as this could cause damage.
We do not recommend the use of power drills/drivers for inserting screws, as this could
over a wide area. This is a feature of toughened glass, and is designed to remove the risk of injury from glass
Do not strike or place heavy weight on the table. Do not place hot items directly onto the glass. Avoid dropping
objects on to the glass, as this may weaken or shatter it. Do not use the glass as a chopping surface.
A weighted parasol base must be used, when using a parasol with this table.
Check you have all the components and tools listed on page 3.
The table is made from toughened glass, which is strong but not unbreakable.

3
1x 2
x 2
x 2
3
2
COMPONENTS - CHAIR FITTINGS
Please check you have all fittings listed below. lf you have any missing or damaged fittings, please contact
your local store.
Note: The quantities below are the correct amount to complete the assembly. In some cases, more fittings
may be supplied than required.
Seat
Left arm
Right arm
A
B
C
M6 x 52mm Bolts
M6 x 52mm Bolts
4mm Allen Key
x 8
x 8
x 1
COMPONENTS - CHAIRS

4
Step 1
Place the right arm (3) onto a non-abrasive surface, such as a carpet, with its holes facing upwards. At the front of
the chair, fasten the seat (1) to arms (2 and 3) using bolts (A). Do not tighten bolts fully at this stage.
Step 2
At the rear of the chair, fasten the seat (1) to arms (2 and 3) using bolts (B). Make sure that all of the bolts have
been tightened completely.
Step 3
Turn the chair to its upright position. Reassemble the other chair.
A
A
B
B
ASSEMBLY INSTRUCTIONS - CHAIRS

5
4x 1
x 4
x 1
6
5
COMPONENTS - TABLE FITTINGS
Please check you have all fittings listed below. lf you have any missing or damaged fittings, please contact
your local store.
Note: The quantities below are the correct amount to complete the assembly. In some cases, more fittings
may be supplied than required.
Table top
Legs
Centre connector
D
E
F
G
Screw ST4.2 x 12
M6 x 20mm Bolts
1.6mm washer Dia. 6.5mm
4mm Allen Key
x 4
x 4
x 4
x 1
COMPONENTS - TABLE

6
Step 1
Place the table top (4) onto a non-abrasive surface, such as a carpet, with its underside facing upwards. lnsert
the legs (5) into the plastic holders attached on the back of the table top (4) rim. Fasten them together using
screws (D).
Step 2
Fasten the centre connector (6) to the middle of the legs (5) using bolts (E) and washers (F). Make sure that all
of the bolts have been tightened completely.
Step 3
Turn the table to its upright position.
4
5
5
5
5
D
6
5
F
E
ASSEMBLY INSTRUCTIONS - TABLE