Honeywell MK7580-30A38-00-A - MS7580 Genesis - Wired Barcode... User manual

MetroSelect®
Area Imaging Supplemental
Configuration Guide

Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether any
such changes have been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein: nor for incidental or consequential damages resulting from the furnishing,
performance, or use of this manual.
This document contains propriety information that is protected by copyright.
All rights reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of HII.
© 2009 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Trademarks
Omniplanar, MetroSet2, Metrologic, MetroSelect, RangeGate, Genesis,
CodeSelect, and Focus are trademarks or registered trademarks of Metrologic
Instruments, Inc. or Honeywell International Inc.
Microsoft and Windows are trademarks or registered trademarks of Microsoft
Corporation.
IBM is a trademark of International Business Machines Corporation.
The Bluetooth word mark is owned by the Bluetooth SIG, Inc. and any use of
such marks by Metrologic Instruments, Inc. or Honeywell International Inc. is
under license.
Other product names mentioned in this manual may be trademarks or
registered trademarks of their respective companies and are the property of their
respective owners.

iii
Table of Contents
Imager Operation
Presentation and Trigger Modes
In-Stand......................................................................................................... 1
Out-of-Stand.................................................................................................. 2
Out-of-Stand / In-Stand Mode Match............................................................. 2
Pass-Through Settings (MS7580 Only)......................................................... 5
Omnidirectional and/or Linear Imager Modes................................................... 6
Aiming and Illumination .................................................................................... 8
Data Output .................................................................................................... 10
Character Suppression................................................................................... 11
Code Bytes 0 – 9............................................................................................ 12
Same Symbol Timeouts ................................................................................. 13
LED Options ................................................................................................... 13
Imager Operation – MS1633
Power Save Modes ........................................................................................ 15
RangeGate Mode ........................................................................................... 16
Firmware Version and Address ...................................................................... 17
Inventory Mode............................................................................................... 18
Code Types and Decode Rules
Data Matrix ..................................................................................................... 23
QR Code ........................................................................................................ 26
MaxiCode ....................................................................................................... 26
Aztec .............................................................................................................. 27
Postal ............................................................................................................. 29
Codablock Options ......................................................................................... 32

iv
PDF Options................................................................................................... 32
RS232
Software Handshaking ................................................................................... 33
Multifunctional USB/IBM Interface.................................................................. 33
Interfaces
Additional Interfaces....................................................................................... 35
MS7580 Genesis Specific .............................................................................. 37
Enter/Exit Configuration Mode ............................................................39
Contact Information ..............................................................................41

1
Imager Operation
Presentation and Trigger†Modes
There are four configurable modes for scanning: the presentation mode,
the multi-try trigger mode, the continuous trigger mode, and the single-trigger
mode. These modes can be configured separately for in-stand and out-of-stand
imager operation‡.
In-Stand‡
* Presentation Mode
In-Stand
Multi-Try Trigger Mode
In-Stand
³420204
³420224
Continuous Trigger Mode
In-Stand
Single Trigger Mode
In-Stand
³420254
³420244
*Factory default configuration.
†The term trigger and button are synonymous.
‡In-Stand and Out-of-Stand references are not applicable for all products.

2
Out-of-Stand‡
Presentation Mode
Out-of-Stand
* Multi-Try Trigger Mode
Out-of-Stand
³418304
³418324
Continuous Trigger Mode
Out-of-Stand
Single Trigger Mode
Out-of-Stand
³418354
³418344
In-Stand/Out-of-Stand Mode Match
Set In-Stand Mode to Match
Out-of-Stand Mode
³4202154
*Factory default configuration for the MS1690, MS1890, and the MS1633.
Factory default configuration for the IS1650.
‡In-Stand and Out-of-Stand references are not applicable for all products.

3
* Presentation Mode
Immediately After Button†Release
³823800
The imager immediately reverts to
presentation mode when the button
is released.
Presentation Mode
1 second After Button Release
³823820
The imager reverts to presentation
mode 1 second after the button is
released.
Presentation Mode
5 seconds After Button Release
³8238100
The imager reverts to presentation
mode when 5 seconds after the
button is released.
*Factory default configuration.
†The term trigger and button are synonymous.
This feature is only supported in the MS7580 Genesis™.

4
* Enable
Trigger Press Timeout
In Presentation Mode
Disable
Trigger Press Timeout
In Presentation Mode
³124403 ³124413
*Factory default configuration.
This feature is only supported in the Focus®product series (i.e., IS1650, MS1890,
MS1633, and the MS1690).

5
Pass-Through Settings
* Enable
Pass-Through Scanning
In Presentation Mode
Disable
Pass-Through Settings
In Presentation Mode
³127015 ³127005
Enable 300 milliseconds
Pass-Through Timeout
³8439300
Enable 100 milliseconds
Pass-Through Timeout
³8439100
*Factory default configuration for the MS7580.
†The term trigger and button are synonymous.
This feature is only supported in the MS7580 Genesis.
Contact a customer service representative for information on additional pass-through
timeout values.

6
Omnidirectional and/or Linear Imager Modes
The area imager can be configured to operate as an omnidirectional imager, or a
linear imager, or a combination of both. Trigger†and presentation operations can
be configured separately for omnidirectional and linear scan modes.
•When a unit is configured to operate as an omnidirectional imager, all
1D and 2D bar codes are scanned omnidirectionally. The only
exceptions are Code 128 scanner configuration labels, which must be
linearly aligned for successful scanning.
Note: The IS4900 area-imaging engines do not require linear
alignment of Code 128 scanner configuration labels. The bar
code should be placed near the center of the engine's field of
view indicated by the targeting dot.
•When a unit is configured to operate as a linear imager, 1D bar codes
must be linearly aligned for successful scanning. In linear configuration
2D bar codes cannot be scanned.
•When a unit is configured to operate as both a linear and
omnidirectional imager, 1D bar codes have to be linearly aligned for
successful scanning while 2D bar codes are scanned omnidirectionally.
By default, the Focus product seriesis configured for omnidirectional scanning
for trigger and presentation operations. By default, the MS7580 is configured to
omnidirectional scanning for presentation and pass-through operations and with
1D linear scanning/2D omnidirectional scanning for button†operations.
Enable Linear Only
in Trigger Operations
Disable Linear Only
in Trigger Operations
³120213
³120203
†The term trigger and button are synonymous.
The Focus product series includes the IS1650, MS1890, MS1633, and the MS1690.