Honeywell IPGSM-4GC User manual

IPGSM-4GC
IP Internet & GSM
Dual Path Fire Communicator
General
The IPGSM-4GC is a fire alarm communicator that offers con-
tact ID reporting with any Fire Alarm Control Panel (FACP) that
has a built-in dialer. This easy to install, dual path communica-
tor connects directly to the primary and secondary communi-
cation ports of a fire panel’s Digital Alarm Communicator
Transmitter (DACT). It offers three selectable reporting paths
which include: Cellular only, IP only, or IP primary/cellular
backup. In the event of an off-normal condition, the fire panel
sends contact ID formatted information to the IPGSM-4GC
communicator panel. The IPGSM-4GC then reformats the
data into highly encrypted Ethernet packets for transmission to
the Alarm-Net receiver via customer provided Internet/Intranet
connection or the GSM network.
Alternative communication methods are critical in the market-
place due to VoIP (Voice over IP), migration from POTS (Plain
Old Telephone Service) and growth of digital radio networks.
The IPGSM-4GC's exclusive dual-path communications solu-
tion combines Internet service with GSM for added reliability
and an extra level of security. All signals from the IPGSM-4GC
communicator panel are delivered to Honeywell’s AlarmNet
Network Control Center, which routes the information to the
appropriate central station. The state of the art AlarmNet net-
work control center is fully redundant and monitored 24/7.
AlarmNet has the ability to route messages using AlarmNet-i
and 800 PLUS services, providing true redundancy and multi-
path message delivery.
The IPGSM-4GC is designed to operate over the most com-
mon GSM platforms including 2G, 3G, and HSPA+. Its multi-
GSM platform technology automatically chooses the best
available cellular signal in the area based on signal strength
and seamlessly self-adjusts to maintain critical life safety com-
munication.
Features
• Saves the cost of two dedicated phone lines.
• Dual path communications. Can communicate to central
station using Internet or cellular technology.
• Requires no change to the existing Fire Alarm Control
Panel configuration. The IPGSM-4GC connects directly to
the primary and secondary telephone ports.
• Operates over the following communication protocols:
HSPA+ (4G), HSPA, HSDPA & HSUPA (3G), EDGE (2G),
GPRS (2G).
• Works over any type of customer provided Ethernet 10/100.
• Base network connection (LAN or WAN), DSL modem or
cable modem.
• Data transmits over standard contact-ID protocol but is
secured with the industry's advanced encryption standard
(AES 256 bit).
• Supports both dynamic (DHCP) or Public and Private Static
IP addressing.
• Built-In Power Supply module: On board charging circuit
design accommodates back-up battery. Includes primary
power and battery supervision.
• Diagnostic LEDs: Signal strength and status indicators.
• Reliable connection: IP and GSM connection tested every
day.
• QOS: Quality of Service diagnostics via AlarmNet conveys
vital communicator information including when message
was received, signal strength, and message path used.
• 7720P Hand-held programmer for easy setup.
Operation
When an event occurs, the Fire Alarm Control Panel goes off
hook to dial the central station. The IPGSM-4GC Dialer Cap-
ture Module detects the off-hook condition and provides the
fire panel with a dial tone. When the fire panel detects the dial
tone, it begins dialing the central station. After the dialing is
completed, the Dialer Capture Module returns a handshake to
the fire panel. The fire panel then sends the contact ID reports
to the Dialer Capture Module, which in turn sends a kiss-off
after the report is successfully received from the fire panel.
The Dialer Capture Module sends the contact ID reports to the
iGSM communications module. When all the reports are sent,
the fire panel goes on-hook. The iGSM communications mod-
ule then transmits the messages to the central station either
over the GSM network or the Internet (primary).
Easy to Program
The IPGSM-4GC communicator can be pre-programmed
using the 7720P programmer to enter all central-station infor-
mation. This is saved to the IPGSM-4GC communicator panel
memory. When the IPGSM-4GC communicator is installed at
the site and connected to the Internet/Intranet, it registers itself
with the AlarmNet receiver. This eliminates the need for a PC
at the remote site for programming.
.For most installations, the only required parameters are:
• Primary City ID (two digits) obtained from your monitoring
station.
• Primary Central Station ID (two digits) obtained from your
monitoring station.
• Primary Subscriber ID (four digits) obtained from your mon-
itoring station.
• Communication Module's MAC ID, and MAC CRC number
located on outside of box, and inside of the module.
All of these parameters are assigned by the monitoring station.
NOTE: Some assembly is required. See Installation and Setup
Guide #800-12458 for full details.
Panel Capabilities
The IPGSM-4GC is compatible with specific fire panels that
use the Contact ID communications format as described in the

Automation and Control Solutions
Honeywell
12 Clintonville Road 1(877) HPP-POWR
Northford, CT 06472-1610 [email protected]
www.honeywellpower.com
This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific
applications or anticipate all requirements. All specifications are subject to change without notice.
©2017 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.
DH-60771:B
June 2017
Made in the U.S.A.
® U.S. Registered Trademark
© 2017 Honeywell International Inc.
Page 2 of 2
SIA DC-05 standard. An additional module is required (HFS-
659EN) when installing the IPGSM-4GC. See the product
installation document for details.
AlarmNet
Honeywell's AlarmNet has been the nationwide leader in
alarm communications technology since 1986. A reliable alter-
native for the transmission of alarm signals, our radio network
provides extensive coverage in the United States and Canada.
AlarmNet Network Control center processes signals from pow-
erful servers in multiple locations equipped with 24/7 infra-
structure support. The AlarmNet network consist of redundant
hardware servers, hot back-up databases and generators with
battery back-up at all locations to ensure continuity of service.
Signals from Alarm-Net are transmitted to the central station's
receivers using multiple communications paths consisting of
the Internet, radio network or toll-free POTS service.
Installation Requirements
ULC COMPLIANCE
• IPGSM-4GC must be mounted in the same room and within
20 feet of the fire panel. The wiring must be routed through
conduit.
• IPGSM-4GC, and all equipment used for the IP connection
(such as the router, hub, modem, etc.) shall be listed, must
be powered from an un-switched branch circuit, and be pro-
vided with appropriate standby power.
• IPGSM-4GC must use the 7AH battery (not supplied) to
provide 24-hour backup capability.
NOTE: When connecting to a fire panel a line fault monitor (Model:
HFS-659EN) must be installed to monitor and report Telco troubles
per the ULC requirement.
Electrical Specifications
• Transformer: 1451-UL9.
–Primary: 120 VAC, 60 Hz, 850mA.
–Secondary: 18VDC, 72 VA.
•Battery
–One 12 V 7.0 AH lead-acid battery (not supplied).
–Battery charging current minimum 1 Amp.
–Battery discharge current standby 230mA, active 950mA.
–IPGSM-4GC cabinet holds one 7.0 AH battery.
Cabinet Specifications
Dimensions: 14.875" H x 12.75" W x 3.0" D (37.8 cm H x 32.4
cm W x 7.6 cm D).
Color: Red.
Shipping Specifications
Weight: 5.3 lbs. (6.94 kg).
Dimensions: 15.625" H x 13.79" W x 9.25" D (39.7 cm H x
34.9 cm W x 23.9 cm D)
Temperature and Humidity Ranges
This system meets NFPA requirements for operation at 0 -
49°C/32 - 120°F and at a relative humidity 93% ± 2% RH (non
condensing at 32°C ± 2°C (90°F ± 3°F). However, the useful
life of the system's standby batteries and the electronic com-
ponents may be adversely affected by extreme temperature
ranges and humidity. Therefore, it is recommended that this
system and its peripherals be installed in an environment with
a normal room temperature of 15 - 27°C/60 - 80°F.
Product Line Information
IPGSM-4GC: (For Canada only): Internet and Digital Cellular
Fire Alarm Communicator Panel. Includes red cabinet with key,
wall outlet box, Dialer Capture Module, iGSM Communications
Module, antenna & mounting adapter, PowerBoost1 power
supply, LED display board, transformer, manual, & required
screws, cables, etc.
HFS-659EN: Telco line fault monitor.
GSM-ANT3DB: 3db gain external/remote antenna.
7626-50HC: 50 ft. antenna cable, low loss.
7626-25HC: 25 ft. antenna cable, low loss.
WA7626-CA: SNA to N Adapter.
7720P: IPGSM-4GC hand held programmer.
HPTCOVER: Plug in transformer box for IPGSM communicator.
BAT-1270: Battery 12 Volts, 7 AH, sealed.
Agency Listings and Approvals
The listings and approvals below apply to the basic IPGSM-4G
communicator panel. In some cases, certain modules may not be
listed by certain approval agencies, or listing may be in process.
Consult factory for latest listing status.
ULC Listed: S789.