Honeywell CIPer 50 User manual

® U.S. Registered Trademark
Copyright © 2021 Honeywell Inc. • All Rights Reserved
31-00198-03
CIPerTM MODEL 50 CONTROLLER
USER GUIDE
July 2021
IMPORTANT NOTE: Email your Host Id to Honeywell WEBs Customer Care ([e-mail]), so that
we can move the license to your organization. For additional queries contact your distributor.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
2
Disclaimer
The material in this document is for information purposes only. The content and the product described are
subject to change without notice. Honeywell makes no representations or warranties with respect to this
document. In no event shall Honeywell be liable for technical or editorial omissions or mistakes in this document,
nor shall it be liable for any damages, direct or incidental, arising out of or related to the use of this document. No
part of this document may be reproduced in any form or by any means without prior written permission from
Honeywell.
Copyright © 2021 HONEYWELL International, Inc. All rights reserved.
Software License Advisory
This document supports software that is proprietary to Honeywell Building Technologies and/or to third party
software vendors. Before software delivery, the end user must execute a software license agreement that governs
software use. Software license agreement provisions include limiting use of the software to equipment furnished,
limiting copying, preserving confidentiality, and prohibiting transfer to a third party. Disclosure, use, or
reproduction beyond that permitted in the license agreement is prohibited.
Trademark Notice
BACnet and ASHRAE are registered trademarks of American Society of Heating, Refrigerating and Air-
Conditioning Engineers. Microsoft, Excel, Internet Explorer, Windows, Windows Vista, Windows Server, and SQL
Server are registered trademarks of Microsoft Corporation. Oracle and Java are registered trademarks of Oracle
and/or its affiliates. Mozilla and Firefox are trademarks of the Mozilla Foundation. Echelon, LON, LonMark,
LonTalk, and LonWorks are registered trademarks of Echelon Corporation.
Niagara Framework ® is a registered trademark of Tridium Inc.
WEBs-AX, WEBs-N4 and WEBStation are registered trademarks of HONEYWELL International, Inc.
CIPerTM is registered trademark of Honeywell Building Technologies.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
3
31-00198-03
TABLE OF CONTENTS
Order numbers (SKU)...............................................................................................................................................................5
HMI configuration principles ......................................................................................................................................................................6
HMI Service..........................................................................................................................................................................................................7
HMI pin...................................................................................................................................................................................................................9
HMI user rights...................................................................................................................................................................................................9
HMI PIN lock-out...............................................................................................................................................................................................10
Enabling the alarming on the HMI ...........................................................................................................................................................11
Enabling the alarm LED on the HMI........................................................................................................................................................11
Adjusting alarm poll-rate for the HMI .....................................................................................................................................................12
Local language HMI menus - translation .............................................................................................................................................13
Login user into the HMI and control the translation .......................................................................................................................13
Filling the Fast Access Lists.........................................................................................................................................................................14
Setting the time format on the home screen.......................................................................................................................................15
Onboard Inputs and Outputs ................................................................................................................................................16
Dual Ethernet.............................................................................................................................................................................17
Separated networks..........................................................................................................................................................................................17
Network switching mode...........................................................................................................................................................................18
Combined network switching & separated networks ...................................................................................................................19
Front USB/Ethernet interface.....................................................................................................................................................................19
Secure Boot –Increased Cyber Security................................................................................................................................................21
Part numbers and supporting material..................................................................................................................................................22
Ordering Part Numbers..............................................................................................................................................................................22
License Upgrades.........................................................................................................................................................................................22
Software Maintenance Agreements.........................................................................................................................................................22
Performance........................................................................................................................................................................................................23
Performance tests ........................................................................................................................................................................................23
PanelBus Communication tuning.........................................................................................................................................................24
Panel-Bus cable type and length...........................................................................................................................................................25
I/O Modules.........................................................................................................................................................................................................26
Pluggable I/O Modules..............................................................................................................................................................................26
Mixed I/O Modules.......................................................................................................................................................................................26
Terminal Sockets...........................................................................................................................................................................................26
Color Coding ...................................................................................................................................................................................................26
LonWorks Product material number Substitution information...............................................................................................28
Compatibility..............................................................................................................................................................................29
WEBs compatibility ..........................................................................................................................................................................................29
Input and Output module compatibility ................................................................................................................................................29
Spyder & Stryker tool compatibility...........................................................................................................................................................30
3rd party modules...............................................................................................................................................................................................30
CIPer Model 50 modules...............................................................................................................................................................................30
WEBs N4 Driver compatibility.....................................................................................................................................................................32
Web-Browser compatibility ..........................................................................................................................................................................33

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
4
CIPer Model 50 Firmware..............................................................................................................................................................................34
Firmware & Hardware compatibility.....................................................................................................................................................34
Firmware upgrade.........................................................................................................................................................................................34
Restore the CIPer Model 50 controller ...................................................................................................................................................35
Resetting CIPer Model 50 controller .......................................................................................................................................................37
Cable...................................................................................................................................................................................................................37
Technical Documentation ............................................................................................................................................................................39
Appendix .....................................................................................................................................................................................40
USB Driver Installation for Windows 7 ....................................................................................................................................................40
USB Driver Installation for Windows 8 ....................................................................................................................................................43
USB Driver Installation for Windows 10 .................................................................................................................................................46

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
5
31-00198-03
Order numbers (SKU)
The onboard HMI is featured in the below listed order numbers:
•WEB-EHSERIESNX26D
•WEB-EHSERIESNX26ND
IMPORTANT
To make efficient use of HMI functionality, it is required to do a few set-up steps in Honeywell
WEBStation N4.4.93 or higher. Refer to section HMI configuration principles given below.
WEB-EHSERIESNX26D
The XL2000HMI can be connected and operated with the below listed OS (SKU) numbers.
WEB-EHSERIESNX26ND

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
6
HMI configuration principles
To get the onboard HMI or detached HMI operational, the following configuration principles need to be done in
WEBs N4:
1. Add & enable the HMI Service.
2. Set a PIN for the HMI access.
3. Add HMI and LED Alarm recipients.
NOTE
As long as there are unacknowledged alarms in the station, the alarm symbol blink
regardless of the user is logged in to the HMI or not. See the picture below:
4. Configure the alarm for the HMI.
5. Fill the Fast Access Lists (FAL) with data points, schedules & parameters.
6. If desired, create a custom HMI sequence.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
7
31-00198-03
HMI Service
The onboard and detached HMI will only work when the HMI Service, called “HonEagleHawkHmiService” has been
placed into the “Services” of your station.
IMPORTANT
Always place the “HonEagleHawkHmiService” into the “Services” folder.
Do NOT place it under any service within “Services”
Steps to configure HMI Service
1. Select the “honEagleHawkHMI” palette and drag the “HonEagleHawkHmiService” into the “Services”
of your station.
2. Enable the “HonEagleHawkHmiService”.
3. Changing, deleting, or translating the messages on the HMI.
4. Changing or deleting can be done in the property sheet of the HMI Service –see below:

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
8
For translating the “Warning” and “Welcome” message of the HMI, you can also use the WEBs N4 Lexicon tool,
see section “Local language HMI menus – translation” in this bulletin

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
9
31-00198-03
HMI pin
PIN, PIN-configuration, and log-off definition are fully integrated with the Niagara “User Service”. This makes it
secure and allows to re-use the user definitions already in place for the station.
NOTE
It is mandatory to enter a 5-digit (Numeric only) PIN here. For security reasons, there is
no default PIN.
If the PIN is not present, the controller will not function.
HMI user rights
In the Admin column (marked red) for the user permissions of the RoleService, it is mandatory to enable “Read”
rights to the categories you want to access via HMI, otherwise, the user will have no access.
You may also provide the “Write” and “Invoke” rights to a category as required.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
10
HMI PIN lock-out
For Cyber Security reasons, users will be locked out after multiple entries of a wrong PIN:
•After three wrong PIN entries in a row, user login is blocked for 1 min. For each wrong PIN after this, the
user must wait for 1 min.
•This time sequence is repeated until a successful login is done.
NOTE
For Cyber Security reasons, all users are blocked during the waiting time.
This is intentional behavior.
1st time wrong PIN:
2nd time wrong PIN:
3rd time wrong PIN:
Wait time is 1 minute for all users.
4th / 5th / 6th / … etc time wrong PIN:
Correct PIN entry will restart the lock-out sequence.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
11
31-00198-03
Enabling the alarming on the HMI
From the “honEagleHawkHMI” palette, drag the “HmiAlarmConsoleRecipient” into the “Alarm Service” and
connect it to the “Default Alarm Class".
Enabling the alarm LED on the HMI
From the “clOnboardIO” palette, drag the “EagleHawkLedRecipient” into the “Alarm Service” and connect it to the
“Default Alarm Class”:

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
12
Adjusting alarm poll-rate for the HMI
The update rate for alarms and data points on the HMI has a default setting.
This can be adjusted with the CPU performance, to balance the information demand.
IMPORTANT
i). The faster the alarm and data-point poll rate, the more impact it will have on the
performance of the station. This might slower the CPU or station performance.
ii). The default setting for alarm and data-point poll-rate is 15s (15.000
milliseconds).
iii). The adjustable range is from 5s to 120s (5.000…120.000 milliseconds).
iv). By default, the poll-rate setting is hidden and can be made visible in the Slot
Sheet.
When adjusting for faster polling, watch the CPU load of the station.
To change the alarm poll rate
1. Select the alarm menu item and select the Slot Sheet:
2. Right-click the “updateIntervalMillis” and uncheck the “Hidden” flag.
3. Double-click the Alarm List in “HonEagleHawkHmiService” and change the poll rate as appropriate.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
13
31-00198-03
Local language HMI menus - translation
The HMI menus can be localized by making use of the standard Lexicon tool of WEBs N4:
•Open Lexicon tool of WEBs N4 and your local language lexicon file
•Open the “honEagleHawkHMI module
•Do the translations and save this lexicon file
•Commission the lexicon file into the controller
•Generate a new user which uses the new language file
Login user into the HMI and control the translation

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
14
Filling the Fast Access Lists
To fill the Fast Access Lists (FAL) with points, parameters, and schedules, you have two options:
•Option 1: Drag and drop points from the Navigation tree on the left into the Fast Access List on the
property sheet on the right.
•Option 2: Use tagging: Drag and Drop “HonTagDictionary” into the “TagDictionaryService”. Select the
point(s) you want to add, open the tag dialog, select the “HonTagDictionary” and select the tag
“FALname”.
In the attached tag, add the name of the Fast Access List(s) you want to have this data point represented in.
Separate multiple Fast Access Lists by using a semicolon “;”

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
15
31-00198-03
Setting the time format on the home screen
1. Make sure that the Lexicon of the desired local language is installed. If not, use the Lexicon Installer
to install it.
2. Set the language in the Station/PlatformService “locale” field.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
16
Onboard Inputs and Outputs
Onboard
Inputs/Outputs
Description
Max. cable
length
WEB-EHSERIESNX26D
WEB-
EHSERIESNX26ND
UI (Universal
Input)
NTC10kΩ(Type II),
NTC20kΩ(Type II),
0…10V, slow BI 0.4 Hz
Short-circuit protected
against 24VAC
1200 ft
(366 m)
8
8
NTC10kΩ(Type II),
NTC20kΩ(Type II),
0…10V fix pull-up, slow
BI 0.4 Hz Short-circuit
protected against 24VAC
1200 ft
(366 m)
2
2
BI (Binary
Input)
open = 24 VDC, closed
2.0 mA, totalizer @ 15 Hz
max. Short-circuit
protected against 24VAC
1200 ft
(366 m)
4
4
AO (Analog
Output)
0..11 V (max. 1 mA)
1200 ft
(366 m)
4
4
BO (Binary
Output)
Relay Normally Open
contact 3A, 250VAC,
30VDC
1200 ft
(366 m)
4
4
Relay Normally Open
contact 10A, 250VAC,
30VDC
1200 ft
(366 m)
1
1
Relay Normally Open
contact with one
common
1200 ft
(366 m)
3
3
For all technical details on Onboard Inputs/Outputs, please refer to the CIPer Model 50 Product Datasheet –31-
00197 and CIPer Model 50 Installation & Commissioning Instructions –31-00233.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
17
31-00198-03
Dual Ethernet
The CIPer Model 50 is equipped with a Dual Ethernet interface. All information about the Dual Ethernet can be
found in the CIPer Model 50 Installation & Commissioning Instructions –31-00233.
Separated networks
SEPARATED NETWORKS = DEFAULT SETTING
For cybersecurity reasons, the default setting of the Dual Ethernet is with the following IP settings:
•Ethernet port 1: IP address 192.168.200.20, subnet 255.255.255.0
•Ethernet port 2: IP address 192.168.201.20, subnet 255.255.255.0

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
18
Network switching mode
Optionally, the Dual Ethernet can be operated in network switching mode.
If this mode is desired, disable one of the Ethernet ports in WEBs N4 –see screenshot below.
Typical application scenarios are a closed BMS networks, like for daisy-chaining plant controllers or daisy-chaining
room controllers on Ethernet.
NOTE
The switching functionality will not work during the power-fail of the CIPer Model 50 controller.
IMPORTANT
Set a gateway address
For the Ethernet switching functionality to work, it is mandatory to enter a Gateway address. If there is
no gateway in the subnet, then use a gateway address that relates to the IP address of the Ethernet
adapter that is enabled.
In the screenshot below, the gateway address is 192.168.1.1, hence the IP address of Ethernet adapter 1 must be
in the range of 192.168.1.2 to 192.168.1.255.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
19
31-00198-03
Combined network switching & separated networks
Optionally separating networks and switching functionality can be combined.
This allows to have one (or more) controllers connected to the customer intranet, and all other controllers residing
in a closed BMS network.
A typical application is the supervisory controller(s) accessible from the customer intranet, and the room
controllers residing in a closed network, and thus being not directly accessible from the customer intranet.
Front USB/Ethernet interface
All details regarding installation and commissioning of the CIPer Model 50 can be found within the Installation &
Commissioning Instructions –31-00233.
All models of the CIPer Model 50 controller are equipped with a USB 2.0 Device interface at the front, which is an
Ethernet over the USB connection.
The permanent IP address of this USB interface is 192.168.255.241.
This interface allows connection of WEBs N4 for programming and operation, and web browsers or 3rd party touch
panels.
If your WEBs N4 PC or your web browser does not connect to this USB interface, the Windows driver may be
missing. In this case, please see Appendix chapters USB Driver Installation for Windows 7, USB Driver Installation
for Windows 8, and USB Driver Installation for Windows 10 installation for WINDOWS 7/8/10”.

CIPerTM MODEL 50 CONTROLLER –USER GUIDE
31-00198-03
20
ATTENTION:
Due to the risk of short-circuiting (see below figure), it is strongly recommended that the CIPer Model 50
controller be supplied with power from a dedicated transformer.
However, if the CIPer Model 50 controller is to be supplied by the same transformer powering other controllers or
devices (e.g., the PW M-Bus Adapter), care must be taken to ensure that correct polarity is observed.
For more details on the Power supply connections and recommended VA ratings, refer to the Power Supply
section in the CIPer Model 50 Installation & Commissioning Instructions –31-00233.