Honeywell Enhanced Micro TDC 3000 User manual

L
8-Node
Enhanced Micro TDC 3000
User’s Manual
MT11-520

L
Implementation
8-Node Micro TDC 3000
8-Node
Enhanced Micro TDC 3000
User’s Manual
MT11-520
Release 500
CE Compliant
9/95

Copyright, Trademarks, and Notices
Printed in U.S.A. – © Copyright 1995 by Honeywell Inc.
Revision 01 – September 15, 1995
While this information is presented in good faith and believed to be accurate,
Honeywell disclaims the implied warranties of merchantability and fitness for a
particular purpose and makes no express warranties except as may be stated in its
written agreement with and for its customer.
In no event is Honeywell liable to anyone for any indirect, special or consequential
damages. The information and specifications in this document are subject to
change without notice.

Enhanced Micro TDC 3000 User’s Manual 9/95
About This Publication
This publication is provided for users of the Enhanced Micro TDC 3000 Control System. Basic
information relating to installation, checkout, implementation, and operation are covered.
This publication is to be used in conjunction with the remainder of the TDC 3000Xbookset.
This publication supports MicroTDC 3000 system software release 500. It also contains hardware
information about the ElectroMagnetic Compatibility Directive for European standards.
Any equipment designated as “CE Compliant” complies with the European Union EMC and
Health and Safety Directives. All equipment shipping into European Union countries after
January 1, 1996 require this type of compliance—denoted by the “CE Mark.”

Enhanced Micro TDC 3000 User’s Manual 9/95
Standard Symbols
Scope The following defines standard symbols used in this publication
ATTENTION Notes inform the reader about information that is required, but not
immediately evident
CAUTION Cautions tell the user that damage may occur to equipment if proper care is
not exercised
WARNING Warnings tell the reader that potential personal harm or serious economic
loss may happen if instructions are not followed
53893
OR Ground connection to building safety ground
53894 Ground stake for building safety ground
53895
DANGER
SHOCK HAZARD Electrical Shock Hazard—can be lethal
53896
DANGER
HIGH VOLTAGE Electrical Shock Hazard—can be lethal
53897 Rotating Fan—can cause personal injury

Table of Contents
Enhanced Micro TDC 3000 User’s Manual i9/95
1 INTRODUCTION AND OVERVIEW
1.1 General Description
1.1.1 Basic Enhanced Micro TDC 3000 Systems
1.1.2 Options to the System
1.1.3 The Operator’s Keyboard
1.1.4 The Engineer’s Keyboard
1.1.5 The Local Control Network
1.2 Operating Practices and Housekeeping
1.2.1 Before Startup
1.2.2 After Startup
1.3 Circuit Card Handling
1.4 Cartridge Disk Handling and Storage
1.4.1 Cartridge Loading and Removal
1.4.2 Cartridge Media Protection
1.5 EMC Directive
1.6 Related Publications
2 SITE PREPARATION AND INSTALLATION
2.1 Storage Conditions
2.2 Site Requirements
2.2.1 Dimensions and Weight
2.3 Electrical Requirements
2.3.1 AC Voltage Options
2.3.2 Frequency
2.3.3 Current in Amperes at 120 Vac
2.4 Unpacking
2.5 Site Layout
2.6 Installation
2.7 Tower #1 Equipment Cabling
2.7.1 Cabling - Standard
2.7.2 Cabling - EMC Directive
2.7.3 Cabling EPDG I/O Board - Standard
2.7.4 Cabling EPDGC I/O Board
2.7.5 Operator Keyboard Cabling
2.7.6 Printer Cabling
2.7.7 Color Monitor Cabling
2.7.8 Engineer’s Keyboard Cabling
2.7.9 TPLCN Cabling
2.7.10 Touchscreen Cabling
2.7.11 Trackball Cabling
2.7.12 Process Cabling
2.7.13 Cabling Diagram and Parts List–Track Ball
2.7.14 Cabling Diagram and Parts List–Touch

Table of Contents
Enhanced Micro TDC 3000 User’s Manual ii 9/95
2.8 Tower #2 Equipment Cabling
2.8.1 Optional Universal Station Upgrade
2.8.2 Optional Redundant Network Interface Module
2.8.3 Optional Computer Gateway CLI I/O
2.8.4 Optional Computer Gateway CLI/A I/O
2.8.5 Optional PLC Gateway
2.9 Optional LCN Upgrade
2.10 Installation Wrap-Up
3 CHECKOUT
3.1 Power-On Tests
3.1.1 Tower #1 Electronics Checks
3.1.2 Tower #2 Electronics Checks
3.1.3 Color Monitor Check
3.1.4 Printer Checks
3.1.5 Cartridge Drive Checks
3.2 System Checkout Wrap-Up
4 IMPLEMENTATION
4.1 Implementation Overview
4.1.1 Database Configuration
4.1.2 The Implementation Process
4.2 System Startup
4.2.1 Local Control Network Configuration
4.2.2 Prebuilt Network Configuration Data
4.3 Load Gateways and Modules
4.3.1 Loading the AM
4.3.2 Loading the NIM
4.4 Load the Process Manager
4.4.1 Standard Double-Sided Nonredundant PM Cabinet
4.4.2 Expanded Standard PM Cabinet
4.4.3 UCN/PM Box Point Configuration Data
4.5 Loading the PLCG or CG
4.6 Data Point Building

Table of Contents
Enhanced Micro TDC 3000 User’s Manual iii 9/95
4.7 Custom Functions
4.7.1 Build Pictures
4.7.2 Build Free Format Logs
4.7.3 Configure Buttons
4.7.4 Prepare User-Written Programs
4.8 Area Database Configuration
4.8.1 Install the Area Database
4.8.2 Area Database Prebuilt Configuration Data
4.9 Configuration Completion
5 OPERATIONAL GUIDELINES
5.1 The Engineering and Operator Personalities
5.1.1 How to Load and Change US Personalities
5.2 Loading the Modules and Gateways
5.2.1 Loading the Application Module
5.2.2 Loading Network Interface Module and UCN Devices
5.2.3 Loading the History Module
5.3 System Operation
5.3.1 Calling Up Operating Displays
5.3.2 The Area Database
5.3.3 Keyswitch Access Levels
5.4 Monitor Operation
5.4.1 IDEK Model MF-5221
5.4.2 IDEK Model MF-8221
5.4.3 HITACHI Model HM-4821-D
6 SERVICE
6.1 Overview
6.2 Field Adjustments
6.2.1 LCN Node Addressing (Pinning)
6.2.2 UCN Node Addressing (Pinning)
6.2.3 21-Inch Monitor Adjustments
6.3 Cleaning
6.3.1 Air Filter Removal and Cleaning
6.4 Troubleshooting
6.5 Spare Parts
6.6 Hardware Verification Test System (HVTS) Overview
A APPENDIX A PREBUILT POINTS
B APPENDIX B BUTTON CONFIGURATION
INDEX

Enhanced Micro TDC 3000 User’s Manual iv 9/95