Honeywell HT-908 Series TECH FORCE User manual

Owner’s Manual
Honeywell is a trademark of Honeywell International inc., used under license to Helen of Troy Limited.
Honeywell International Inc. makes no representation or warranties with respect to this product.
TurboForce is a registered trademark owned by Helen of Troy Limited.
TURBO FORCE®
HIGH VELOCITY
CIRCULATORS
HT-900 Series, HT-908 Series
and HF-910 Series
IMPORTANT SAFETY
INSTRUCTIONS
READ AND SAVE THESE SAFETY
INSTRUCTIONS BEFORE USING
THIS FAN
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
FOR US MODELS ONLY - This product
employs overload protection (fuse).
A blown fuse indicates an overload or
short-circuit situation. If the fuse blows,
unplug the product from the outlet.
Replace the fuse as per the user servicing
instructions (follow product marking for
proper fuse rating) and check the product.
If the replacement fuse blows, a short-
circuit may be present and the product
should be discarded or returned to an
authorized service facility for examination
and/or repair.
1. Use this fan only as described in this
manual. Other use not recommended,
may cause fire, electric shock or injury
to persons.
2. This product is intended for household
use ONLY and not for commercial,
industrial or outdoor use.
3. To protect against electric shock, do not
place fan in window, immerse unit, plug
or cord in water or spray with liquids.
4. This appliance has a polarized plug (one
blade is wider than the other). To reduce
the risk of shock, this plug is intended
to fit only one way in a polarized outlet.
If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT
attempt to defeat this safety feature.
5. Close supervision is necessary when any
appliance is used by or near children.
6. Turn the fan to the OFF position and
unplug the fan from the outlet when not
in use, when moving the fan from one
location to another and before cleaning.
7. To disconnect the fan, first turn control
to the OFF position, grip the plug and
pull it from the wall outlet. Never pull
by the cord.
8. Do not operate the fan in the presence
of explosive and/or flammable fumes.
9. Do not place the fan or any parts near
an open flame, cooking or other heating
appliance.
10. Do not operate fan with an extension cord.
11. Do not operate the fan with a damaged
cord or plug or if the product malfunctions,
is dropped or damaged in any manner
(see warranty).
12. Avoid contact with moving fan parts.
13. The use of attachments not
recommended by the manufacturer
may be hazardous.
14. Place the fan on a dry level surface.
15. Do not hang or mount fan on ceiling.
HF-910, HT-908 Series cannot be
wall mounted.

USER SERVICING INSTRUCTIONS
• If your fan loses power and you suspect that the fuse on your fan
has blown, grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
• Slide fuse cover, located on the top of the plug, towards the prongs
of the plug. (Fig. 1)
• Carefully remove the blown fuse and snap a new fuse into place. To
reduce the risk of fire, replace fuse only with 2.5 Amp, 125 volt fuse.
Fully close the fuse door by sliding back into place. Discard the blown
fuse. The plug should now be ready for normal use. (Fig. 2)
• To reduce the risk of fire, do not replace attachment plug. Contains
a safety device (fuse), that should not be removed. Discard product
if the attached plug is damaged.
• If you need further information on how or when to replace the fuse in
the safety plug, please contact Kaz Consumer Relations Department
by visiting our website at www.honeywellpluggedin.com/fans or
calling 1-800-477-0457.
The Turbo Force®High Velocity Air Circulator Fans are aerodynamically
designed to give you the versatility of changing this fan’s angular direction
simply by adjusting the fan to ANY desired angular output (Fig.3). Upon
using this fan, you will feel a strong and powerful air stream that will
quickly move air to provide a cooling effect.
INTRODUCTION
Fig. 3
FOR ENERGY SAVINGS ALL YEAR
Honeywell Air Circulator Fans can help save energy and can lower
monthly utility bills all year round. Our air circulators increase
distribution of cooler air from your air conditioner or warmer air
from your heating system, creating a vortex of air flow for increased
comfort. Increased air flow allows the air conditioning and heating
systems to be used at lower settings to help save you money.
In the summer:
Circulate cool
air by using
with window
or central air
conditioning.
Circulate cool
air upstairs.
In the winter:
Circulate warm
air. Position your
air circulator in
an open location
for upward air
movement.
Run it on a low
setting to move
the hotter air
from the ceiling
and circulate
the warmer air
throughout the
room.
Increase Heating Source Efficiency: Use
with other heat sources, such as wood stoves,
baseboard heaters, and or vents to help circulate
the warm air throughout the room.
This fan features a fused safety plug which is designed to cut off electric current to the fan if an
electrical fault occurs. Please see below for more information on how to properly use your fan and
replace the safety plug fuse, if needed.
FUSED SAFETY PLUG - FOR US MODELS ONLY
16. Do not operate if the fan housing is
removed or damaged.
17. A loose fit between the AC outlet
(receptacle) and plug may cause
overheating and a distortion of the plug.
Contact a qualified electrician to replace
loose or worn outlet.
18. Do not operate any fan with a damaged
cord or plug. Discard any damaged fan,
or return the fan to the retailer where the
fan was purchased, or request a return
authorization to return to Kaz USA, Inc.
for examination and/or repair.
19. Do not run fan cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange
cord away from traffic areas and where
it will not be tripped over.
WARNING: To Reduce The Risk
of Fire or Electric Shock, Do Not Use
This Fan With Any Solid State Speed
Control Device
Fig. 1
Fig. 2

USER SERVICING INSTRUCTIONS
• If your fan loses power and you suspect that the fuse on your fan
has blown, grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
• Slide fuse cover, located on the top of the plug, towards the prongs
of the plug. (Fig. 1)
• Carefully remove the blown fuse and snap a new fuse into place. To
reduce the risk of fire, replace fuse only with 2.5 Amp, 125 volt fuse.
Fully close the fuse door by sliding back into place. Discard the blown
fuse. The plug should now be ready for normal use. (Fig. 2)
• To reduce the risk of fire, do not replace attachment plug. Contains
a safety device (fuse), that should not be removed. Discard product
if the attached plug is damaged.
• If you need further information on how or when to replace the fuse in
the safety plug, please contact Kaz Consumer Relations Department
by visiting our website at www.honeywellpluggedin.com/fans or
calling 1-800-477-0457.
The Turbo Force®High Velocity Air Circulator Fans are aerodynamically
designed to give you the versatility of changing this fan’s angular direction
simply by adjusting the fan to ANY desired angular output (Fig.3). Upon
using this fan, you will feel a strong and powerful air stream that will
quickly move air to provide a cooling effect.
INTRODUCTION
Fig. 3
FOR ENERGY SAVINGS ALL YEAR
Honeywell Air Circulator Fans can help save energy and can lower
monthly utility bills all year round. Our air circulators increase
distribution of cooler air from your air conditioner or warmer air
from your heating system, creating a vortex of air flow for increased
comfort. Increased air flow allows the air conditioning and heating
systems to be used at lower settings to help save you money.
In the summer:
Circulate cool
air by using
with window
or central air
conditioning.
Circulate cool
air upstairs.
In the winter:
Circulate warm
air. Position your
air circulator in
an open location
for upward air
movement.
Run it on a low
setting to move
the hotter air
from the ceiling
and circulate
the warmer air
throughout the
room.
Increase Heating Source Efficiency: Use
with other heat sources, such as wood stoves,
baseboard heaters, and or vents to help circulate
the warm air throughout the room.
This fan features a fused safety plug which is designed to cut off electric current to the fan if an
electrical fault occurs. Please see below for more information on how to properly use your fan and
replace the safety plug fuse, if needed.
FUSED SAFETY PLUG - FOR US MODELS ONLY
16. Do not operate if the fan housing is
removed or damaged.
17. A loose fit between the AC outlet
(receptacle) and plug may cause
overheating and a distortion of the plug.
Contact a qualified electrician to replace
loose or worn outlet.
18. Do not operate any fan with a damaged
cord or plug. Discard any damaged fan,
or return the fan to the retailer where the
fan was purchased, or request a return
authorization to return to Kaz USA, Inc.
for examination and/or repair.
19. Do not run fan cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange
cord away from traffic areas and where
it will not be tripped over.
WARNING: To Reduce The Risk
of Fire or Electric Shock, Do Not Use
This Fan With Any Solid State Speed
Control Device
Fig. 1
Fig. 2

WALL MOUNTING (HT-900 Series Only)
• Locate and mark the position on the wall where the fan will be mounted (preferably at a wall stud).
• Insert two screws into the wall stud. (Screws are not included and can be purchased at a
hardware store)
• Use #8, 1” length screws, leave 3/8” below screw head (bolt) exposed from the wall.
• Line up the openings on the base of the fan with the screws (bolts) and hang the fan on the wall.
NOTE: HF-910 Series and HT-908 Series cannot be wall-mounted
CLEANING AND STORAGE
Unplug the fan before cleaning.
• Use only a soft, damp cloth to gently wipe the fan clean.
• DO NOT immerse the fan in water and never allow water to drip into
the motor housing.
• DO NOT use gasoline, paint thinner or other chemicals to clean the fan.
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
REMOVAL OF THE FRONT GRILLE FOR CLEANING
DO NOT remove the fan grille unless the power is turned off and
the power cord is unplugged.
• Gently lay the fan face down on a table (Fig. 6).
• Screws are located in the holes around the back grille of the fan (Fig. 7).
• After the screws in each hole are located, insert a standard Phillips Head
screw driver into one of the screw holes.
NOTE: Screwdriver head should fit comfortably in the hole without being
too tight or leaving too much room. A screwdriver with a head that is
too small will have trouble engaging the screw.
• Each screw should be engaged and loosened by unscrewing each head
to the left.
• Once all screws have been loosened, slowly lift the fan up off the surface
using the back carrying handle, and separate the front grille along the seam
where the screws were located (Fig. 8).
NOTE: Screws will sometimes fall out of the back of the unit
once loosened, so be sure not to stand the fan up or tip it
over too quickly.
• To reassemble the fan, collect all of the screws and lay the fan on its back
(Fig. 9).
• Place the front grille onto the unit, lining up the notch in the grille,
with the notch along the bottom of the fan (Fig. 10).
• Once the grille is aligned with the body of the fan, and each screw hole
matches up, flip the unit to lay it face down on a flat surface.
• Insert each screw into a hole and gently tighten each screw. Ensure that
the front grille and the bottom of the fan are tightly secured together.
• For storage, clean the fan carefully as instructed. Store the fan in the
original packaging or cover the product to protect it from dust.
OPERATION
• Be sure the fan is in the OFF position.
• Place your fan on a dry, level surface.
• Plug the power cord into a polarized 120 volt AC wall outlet.
• To operate, turn the control knob to the desired fan speed: HIGH (III),
MEDIUM (II) or LOW (I) (Fig. 4).
• Adjust the fan to the desired angular air output direction.
• To move the fan, turn the fan OFF and pick it up by the concealed handle
that is located on the outside rim of the fan (Fig. 5).
Fig. 4
Fig. 5

WALL MOUNTING (HT-900 Series Only)
• Locate and mark the position on the wall where the fan will be mounted (preferably at a wall stud).
• Insert two screws into the wall stud. (Screws are not included and can be purchased at a
hardware store)
• Use #8, 1” length screws, leave 3/8” below screw head (bolt) exposed from the wall.
• Line up the openings on the base of the fan with the screws (bolts) and hang the fan on the wall.
NOTE: HF-910 Series and HT-908 Series cannot be wall-mounted
CLEANING AND STORAGE
Unplug the fan before cleaning.
• Use only a soft, damp cloth to gently wipe the fan clean.
• DO NOT immerse the fan in water and never allow water to drip into
the motor housing.
• DO NOT use gasoline, paint thinner or other chemicals to clean the fan.
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
REMOVAL OF THE FRONT GRILLE FOR CLEANING
DO NOT remove the fan grille unless the power is turned off and
the power cord is unplugged.
• Gently lay the fan face down on a table (Fig. 6).
• Screws are located in the holes around the back grille of the fan (Fig. 7).
• After the screws in each hole are located, insert a standard Phillips Head
screw driver into one of the screw holes.
NOTE: Screwdriver head should fit comfortably in the hole without being
too tight or leaving too much room. A screwdriver with a head that is
too small will have trouble engaging the screw.
• Each screw should be engaged and loosened by unscrewing each head
to the left.
• Once all screws have been loosened, slowly lift the fan up off the surface
using the back carrying handle, and separate the front grille along the seam
where the screws were located (Fig. 8).
NOTE: Screws will sometimes fall out of the back of the unit
once loosened, so be sure not to stand the fan up or tip it
over too quickly.
• To reassemble the fan, collect all of the screws and lay the fan on its back
(Fig. 9).
• Place the front grille onto the unit, lining up the notch in the grille,
with the notch along the bottom of the fan (Fig. 10).
• Once the grille is aligned with the body of the fan, and each screw hole
matches up, flip the unit to lay it face down on a flat surface.
• Insert each screw into a hole and gently tighten each screw. Ensure that
the front grille and the bottom of the fan are tightly secured together.
• For storage, clean the fan carefully as instructed. Store the fan in the
original packaging or cover the product to protect it from dust.
OPERATION
• Be sure the fan is in the OFF position.
• Place your fan on a dry, level surface.
• Plug the power cord into a polarized 120 volt AC wall outlet.
• To operate, turn the control knob to the desired fan speed: HIGH (III),
MEDIUM (II) or LOW (I) (Fig. 4).
• Adjust the fan to the desired angular air output direction.
• To move the fan, turn the fan OFF and pick it up by the concealed handle
that is located on the outside rim of the fan (Fig. 5).
Fig. 4
Fig. 5