Honeywell BW Ultra User manual

Honeywell BW™ Ultra
User Manual
| Gas Detection
Portable Five-gas Detector
with Internal Pump

BW Technologies by Honeywell LP (Honeywell) warrants
the product to be free from defects in material and
workmanship under normal use and service for a period
of three years, beginning on the date of shipment to the
buyer. This warranty extends only to the sale of new and
unused products to the original buyer. Honeywell’s warranty
obligation is limited, at Honeywell’s option, to refund of the
purchase price, repair, or replacement of a defective product
that is returned to a Honeywell authorized service center
within the warranty period. In no event shall Honeywell’s
liability here under exceed the purchase price actually paid
by the buyer for the product.
This warranty does not include:
•fuses,disposablebatteries,ortheroutinereplacement of partsduetothenormal
wear and tear of the product arising from use;
•any damage or defects attributable to repair of the product by any person other
thananauthorizeddealer, or the installationofunapprovedparts on theproduct
•any product which in Honeywell’s opinion has been misused, altered, neglected,
or damaged by accident or abnormal conditions of operation, handling, or use.
The obligations set forth in this warranty are conditional on:
•Properstorage,installation, calibration,use, maintenance, andcompliance with
the product manual instructions and any other applicable recommendations of
Honeywell.
•The buyer promptly notifying Honeywell of any defect and, if required, promptly
making the product available for correction. No goods shall be returned to
Honeywell until receipt by the buyer of shipping instructions from Honeywell.
•Theright of Honeywelltorequirethat the buyer provides proofof purchase such
as the original invoice, bill of sale, or packing slip to establish that the product is
within the warranty period.
THE BUYER AGREES THAT THIS WARRANTY IS THE
BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. HONEYWELL SHALL NOT BE
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING
LOSS OF DATA, WHETHER ARISING FROM BREACH OF
WARRANTY OR BASED ON CONTRACT, TORT, OR RELIANCE
OR ANY OTHER THEORY.
Since some countries and states do not allow limitation of
the term of an implied warranty, or exclusion or limitation
of incidental or consequential damages, the limitations
and exclusions of this warranty may not apply to every
buyer. If any provision of this warranty is held invalid or
unenforceable by a court of competent jurisdiction, such
holding will not affect the validity or enforceability of any
other provision.
Limited Warranty and Limitation of Liability
Warranty Registration
https://sps.honeywell.com/us/en/support/safety/hgas-product-
registration

Maintenance.................................................................................................... 12
Maintenance..............................................................................................................................12
Gas Cylinder Guidelines........................................................................................................12
Charge the Battery...................................................................................................................12
Maintain the Battery...............................................................................................................12
Real Time Clock Display........................................................................................................12
Languages...................................................................................................................................13
Clean the Detector...................................................................................................................13
Upgrade the Firmware...........................................................................................................13
Upgrade the Firmware...........................................................................................................13
Appendices....................................................................................................... 14
Auto detect gas .........................................................................................................................14
Gas Alarm Setpoints................................................................................................................14
Sample Factory Alarm Setpoints.......................................................................................14
Specifications ............................................................................................................................14
Standards and Certifications..............................................................................................15
Sensor T90 Ratings.................................................................................................................17
Label Information.....................................................................................................................18
BW Ultra Battery label.................................................................................................18
BW Ultra Instrument label........................................................................................20
Part Number Format...............................................................................................................22
Sensor Replacement...............................................................................................................23
Troubleshooting .......................................................................................................................24
Glossary........................................................................................................................................25
Contact Honeywell ..................................................................................................................26
Before You Begin ............................................................................................... 1
About this Publication...............................................................................................................1
Trademarks..........................................................................................................................1
Introduction...................................................................................................................................1
What’s in the Box.........................................................................................................................1
Monitored Gases..........................................................................................................................1
Safety Information...................................................................................................................... 2
Sensor Poisons and Contaminants..................................................................................... 3
International Symbols...............................................................................................................3
Getting Started................................................................................................... 4
Appearance....................................................................................................................................4
Main Screen..............................................................................................................................................................................................................................4
Screen Icons..................................................................................................................................4
Alarms............................................................................................................................................... 5
Alternate Display Background...............................................................................................6
Detector Operations ......................................................................................... 7
Activate the detector.................................................................................................................. 7
Activate the backlight................................................................................................................ 7
Deactivate the detector............................................................................................................7
Navigate the menu.....................................................................................................................7
View detector’s general information................................................................................... 7
Reset TWA or STEL readings..................................................................................................7
Reset Peak readings...................................................................................................................7
Reset TWA/STEL and Peak readings.................................................................................. 8
Zero sensors...................................................................................................................................8
Acknowledge alarms and messages...................................................................................8
Latching Alarms...........................................................................................................................8
Calibrate the detector ............................................................................................................... 8
Select PID Correction Factor..................................................................................................9
Start a Bump Test........................................................................................................................ 9
Perform a manual bump test.....................................................................................9
Set up IntelliFlash....................................................................................................................... 9
Set up Reverse IntelliFlash...................................................................................................10
Set up the Confidence and Compliance Beep interval...........................................10
Select an operation mode.....................................................................................................10
Essentials mode.............................................................................................................10
Hole Watch mode..........................................................................................................10
Inert mode.........................................................................................................................10
Configure the Detector..........................................................................................................11
Connect With IntelliDoX........................................................................................................11
Connect With an IR Link........................................................................................................11
Bluetooth Pairing.....................................................................................................................12
Replace a Sensor......................................................................................................................12
Review Logs................................................................................................................................12
Table of Contents

BW Ultra User Manual 1
Before You Begin
About this Publication
While this information is presented in good faith and
believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular
purpose and makes no express warranties except as may be
stated in its written agreement with and for its customers.
InnoeventisHoneywellliabletoanyoneforanyindirect,special,
orconsequentialdamages.Theinformationandspecifications
in this document are subject to change without notice.
Trademarks
Brand or product names are trademarks of their respective
owners. The following brand or product names are
trademarks of Honeywell:
•Honeywell BW™ Ultra •IntelliDoX
•IntelliFlash •Reverse IntelliFlash
Introduction
The Honeywell BW™ Ultra gas detector warns of hazardous
gas at levels above user-defined alarm setpoints.
The detector is a personal safety device. It is
your responsibility to respond properly to the alarm.
This publication is intended for people who understand
how to configure, maintain and use personal gas
detectors, docking systems, and accessories.
What’s in the Box
•Honeywell BW™ Ultra gas
detector
•1 Screen protector
•Battery (factory-installed) •Screwdrivertelescopewithdoubleend
•Charging adapter •Quick Reference Guide
•3m PVC tube •1 Dust porous filter 7/16”
•2 Fitting mini quick connector
to 1/8”
•2 Fitting male LuerLock to 1/8”
•5 Pump filters
Monitored Gases
The detector can monitor up to five gases at a time. Four
gases detected by default, and one optional gas selected
from the following list.
Monitored Gas Unit of Measure
Default detected gases
Hydrogen Sulfide (H2S) parts per million (ppm)
Carbon Monoxide (CO) parts per million (ppm)
Oxygen (O) % volume
Combustible gases (LEL)
Lower explosive limit
a) percent of lower explosive limit (%LEL)
b) percent by volume methane 05.0% v/v
Optional gases
IR Flammable (IR LEL) % volume
Hydrogen (H2) parts per million (ppm)
Sulfur Dioxide (SO2) parts per million (ppm)
IRCarbon Dioxide (CO2) parts per million (ppm) or % volume
Ammonia (NH3) parts per million (ppm)
Volatile Organic Compounds
(VOC)
parts per million (ppm)
Chlorine (Cl2) parts per million (ppm)
Nitrogen Dioxide (NO2) parts per million (ppm)
Hydrogen Cyanide (HCN) parts per million (ppm)
Nitric Oxide (NO) parts per million (ppm)
CO sensor with a Hydrogen
filter (COH)
parts per million (ppm)
NOTE:
CO is now available in %vol

BW Ultra User Manual2
Safety Information
aCAUTION
READ THIS FIRST
Use the detector only as specified in this manual, otherwise
the protection provided by the detector may be impaired.
•Onlytheinstrumentcapableofsoundingthealarms andshowingreadingsona
displayshouldbeusedforimmediatesafetycriticaluse.Wirelesscommunication
and infrastructure are only for informational monitoring.
•Use only Honeywell approved batteries (order number: HUBAT (P/N:
50122982130) with the Honeywell BW™ Ultra detector. Using any other
battery can cause an explosion or fire.
•Thelithiumbatteryinthisproductpresents a risk of fire,explosion,andchemical
burn if misused. Do not open, crush, disassemble, incinerate, or heat above
100°C (212°F). Batteries exposed to heat at 130°C (266°F) for 10 minutes
can cause fire and explosion. Follow the manufacturer’s instruction. Batteries
must only be charged and/or replaced in a hazardous free area.
•Deactivating the detector by removing the battery pack may cause improper
operation and harm the detector.
•Use only Honeywell approved battery charger, that is certified for SELV/LVLC
(isolated) with an output Um of 6.3 V.
•If using the detector near its upper or lower operating temperature, Honeywell
recommends zeroing or activating the detector in that environment.
•Chargethedetectorbeforefirst-timeuse.Honeywellrecommendsthedetector
also be charged after every workday.
•Calibrate the device on a regular schedule, depending on use and sensor
exposure to poisons and contaminants. Honeywell recommends calibrating at
least once every six months.
•For optimal performance, periodically zero the sensor in a normal atmosphere
(20.9% v/v O) that is free of hazardous gas.
•Thecombustiblesensorisfactorycalibratedto50% LEL methane.Ifmonitoring
a different combustible gas in the % LEL range, calibrate the sensor using the
appropriate gas.
•Only the combustible gas detection portion of this detector has been assessed
for performance by CSA standard.
•Honeywell recommends that the combustible sensor is checked with a known
concentration of calibration gas after any exposure to contaminants/poisons
such as sulfur compounds, silicone vapors, halogenated compounds, etc.
•Honeywell recommends that the sensors be bump tested before each day’s
use to confirm their ability to respond to gas. Manually verify that the audible,
visual, and vibratoralarms areactivated.Calibrateifthe readingsarenot within
the specified limits.
•The detector is designed for use only in potentially explosive atmospheres
where oxygen concentrations do not exceed 20.9% (v/v). Oxygen deficient
atmospheres (<10% v/v) may suppress some sensor outputs.
•Extended exposure of the detector to certain concentrations of combustible
gases and air may stress the detector element and seriously affect its
performance. If an alarm occurs due to a high concentration of combustible
gases,acalibrationshouldbeperformed.Ifnecessary,contactHoneywellservice
representative to replace the sensor.
•High concentrations of certain toxic gases, for example, HS, may hurt the LEL
sensor. This effect, known as inhibition, is usually temporary but in extreme
circumstancescanimpairthesensitivityoftheLELsensorafteranygasexposure
that causes alarm in the toxic gas sensors.
•The Honeywell BW™ Ultra is provided with an antistatic coating over the LCD
window to minimize the risk of ignition due to electrostatic discharge. Periodic
inspection of this coating is required to ensure no degradation, delamination,
abrasions or other deformities to this surface.
•Care must be taken to avoid exposure to excessive heat, harsh chemicals or
solvents, sharp edges and abrasive surfaces. Clean the exterior with a soft,
damp cloth.
•Portable safety gas detectors are life safety devices. The accuracy of ambient
gas reading(s) is dependent upon factors such as accuracy of the calibration
gas standard used for calibration and frequency of calibration.
•When Honeywell BW™ Ultra detector is equipped with Infrared (IR) sensor, do
NOT use BW Ultra at an atmospheric pressure exceeding 110 kPa (1.1 bar).
The IR sensor used in the detector is intended for use at atmospheric pressure
and shall not be used in pressures exceeding 110 kPa (1.1 bar).
•DONOTrelyontheBluetoothBWUltraoutputindicationforsecurity purposes.
aWARNINGS
•FOR SAFETY REASONS THIS EQUIPMENT MUST BE OPERATED AND
SERVICED BY QUALIFIED PERSONNEL ONLY. READ AND UNDERSTAND
INSTRUCTION MANUAL COMPLETELY BEFORE OPERATING OR SERVICING.
•Substitution of components may impair Intrinsic Safety.
•Protect the combustible sensor from exposure to lead compounds, silicones,
and chlorinated hydrocarbons. Although certain organic vapors (such as
leadedgasolineandhalogenatedhydrocarbons)cantemporarilyinhibitsensor
performance, in most cases the sensor will recover after calibration.
•TheCanadianStandardsAssociation(CSA)requirestheLELsensortobebump
tested before each day’s use with calibration gas containing between 25%
and 50% LEL. The instrument must be calibrated if the displayed LEL value
during a bump test fails to fall between 100% and 120% of the expected
value for the gas.
•High off-scale LEL readings may indicate an explosive concentration.
•Anyrapidupscalingreadingfollowedbyadecliningorerraticreadingmayindicate
a gas concentration beyond the upper scale limit, which can be hazardous.
•Products may contain materials that are regulated for transportation under
domestic and international dangerous goods regulations. Return product in
compliance with appropriate dangerous goods regulations. Contact freight
carrier for further instructions.
•Dispose of used lithium cells immediately. Do not disassemble and do not
disposeofinfire.Donotmixbatterieswiththesolidwastestream.Spentbatteries
should be disposed of by a qualified recycler or hazardous materials handler.
Keep children away from the lithium cells.
•The pellistors used in the Catalytic flammable gas sensor can suffer from a
loss of sensitivity when in the presence of poisons or inhibitors, e.g. silicones,
sulphides, chlorine, lead or halogenated hydrocarbons.
•DONOTrelyontheBluetoothBWUltraoutputindicationforsecurity purposes.
•DONOTusethescreenprotectorinthehazardouslocation.The screenprotector
must be removed in the explosive atmospheres.
•Theaccessories(e.g.,fittingminiquick-connectorto1/8”,fittingmaleLuer-lock
to 1/8” etc.) are not the scope of intrinsic safe certification
•Do not install or remove any components when an explosive gas atmosphere
is present.

BW Ultra User Manual 3
a MISES EN GARDE
•POUR DES RAISONS DESECURITE, CET EQUIPEMENT DOlT ETRE UTILISE,
ENTRETENU ET REPARE UNIQUEMENT PAR UN PERSONNEL QUALIFIE.
ETUDIER LE MANUEL D’INSTRUCTIONS EN ENTIER AVANT D’UTILISER,
‘ENTRETENIR OU DE REPARER L’EQUIPEMENT.
•Avertissement : Le remplacement d’un composant de l’appareil peut altérer
sa sécurité intrinsèque.
•Pour éviter l’inflammation d’atmosphères inflammables ou combustibles,
couper l’alimentation électrique avant tout entretien.
•Avertissement: Pour réduire le risque d’ignition dans les atmosphères
inflammables, les piles doivent êtrechargéesinadansunezonesûre,exempte
de gaz dangereux.
•Protégezlecapteurdegazcombustiblescontretouteexpositionauxcomposés
de plomb, aux silicones et aux hydrocarbures chlorés. Bien que certaines
vapeurs organiques (comme l’essence au plomb ou les hydrocarbures
halogénés)puissentneutraliserprovisoirementlesperformances du capteur,
dans la plupart des cas, le capteur retrouvera son fonctionnement normal
après l’étalonnage.
•Attention : Des valeurs LIE hors échelle élevées peuvent indiquer la présence
d’une concentration explosive.
•Toute mesure en rapide augmentation suivie d’une diminution ou d’une
mesurefantaisistepeutindiqueruneconcentrationdegazau-delàdela limite
d’échelle supérieure, risquant donc d’être dangereuse.
•Les produits peuvent contenir des matériaux qui sont réglementés pour
le transport en vertu des règlements nationaux et internationaux de
marchandises
•dangereuses. Retourner le produit conformément à la réglementation sur
les marchandises dangereuses appropriées. Contactez transporteur pour
plus d’instructions.
•Avertissement: La batterie au lithium peut présenter un risque d’incendie ou
de brûlure chimique en cas de mauvaise utilisation. Elle ne doit jamais être
démontée, incinérée ni chauffée au-delà de 100 °C.
•Avertissement: Les piles au lithium polymère exposées à une température
supérieure à 130 °C pendant plus de 10 minutes peuvent provoquer un
incendie et/ou une explosion.
•Mettez immédiatement au rebut les batteries au lithium usagées. Ne pas
démonter et ne pas jeter au feu. Ne pas les mélanger aux autres déchets
solides. Les piles usagées doivent être éliminées par un centre de recyclage
agréé ou un centre de traitement des matières dangereuses. Éloignez les
enfants des piles au lithium.
•Ne comptez PAS sur l’indication de sortie Bluetooth BW Ultra à des fins de
sécurité.
•N’utilisez PASle protecteur d’écran dansun endroit dangereux.Leprotecteur
d’écran doit être retiré dans les atmosphères explosives
Sensor Poisons and
Contaminants
Many chemicals can contaminate and permanently
damage sensors. Follow these guidelines when using
cleaners, solvents, or lubricants near the detector:
•Use water-based (not alcohol-based) cleaners
•Clean the exterior only with a soft, damp, cloth
These products can damage the sensors. Do not use them
around the detector:
•Soaps •Tissues containing silicone
•Solvents •Aerosols
•Alcohol-based cleaners •Anionic detergents
•Brake cleaners •Citrus-based cleaners
•Dishsoaps •Hand sanitizers
•Insect repellents •Lubricants
•Methanol (fuel or antifreeze) •Mold release agents
•Polishes •Rust inhibitors
•Window and glass cleaners •Silicone-based adhesives,
sealants, or gels
•Silicone-based cleaners or
protectants
•Hand/body/medicinal creams
containing silicone
International Symbols
Symbol Meaning
Approved to both United States and Canada
standards by UL LLC.
IECEx
International Electrotechnical Commission
Scheme for Certification to Standards for
Electrical Equipment for Explosive Atmospheres
Natural Institute of Metrology, Quality, and
Technology. Conforms to Brazilian
INMETRO Certification.
ATEX Conforms to European ATEX Directives
JPEx Examination for Electrical Equipment used in
Potentially Explosive Atmospheres
Japanese Certificate Scheme.
UK Conformity Assessed marking indicates
conformity with the applicable requirements for
products sold within Great Britain.
NCC Warning Statement :
「取得審驗證明之低功率射頻器材，非經核准，公司、商號或
使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通
信；經發現有干擾現象時，應立即停用，並改善至無干擾時方
得繼續使用。前述合法通信，指依電信管理法規定作業之無線
電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療
用電波輻射性電機設備之干擾。」”

BW Ultra User Manual4
Screen Icons
The detector’s screen, shown here with typical icons, will
display those shown in the following table as conditions
dictate.
BW ULTRA
Screen Icons
BLE Pump/header
BLE Pairing Error Pump passed
Paired Pump critical fail
Pairing failed Warning/failure/error/
low battery
Stealth mode Press button
Battery -three levels Press & hold button
Low battery Hole watch mode high
IR LINK connection Hole watch mode low
Calibration passed Hole watch Oxygen
bar
Calibration failed Target gas
Calibrationcancelled Inert mode
Bump test cancelled Sensor failure
Bump test passed STEL alarm
Bump test failed TWA alarm
Correction factor Peak gas exposure
Over limit alarm Firmware update in
progress
High alarm Sensor disabled
Low alarm
This icon flashes
to indicate regular
operation without
any gas alarms or
functional errors
Getting Started
Appearance
1
1
1
2
4
3
5
6
8
7
9
1. Visual alarm indicator
2. Exhaust port
3. Screen
4. Button
5. Beeper Aperture
6. Pump inlet
7. Alligator clip
8. Pump assembly
9. Charging connector and IR Interface
Main Screen.
The start-up main screen is displayed as follows:

BW Ultra User Manual 5
Alarms
When the detector goes into alarm, it flashes, vibrates,
and produces a loud siren noise. Depending on the type of
alarm, these flashes, vibrations, and noises will be different.
NOTE: In Stealth mode the Honeywell BW™ Ultra only
vibrates.
IMPORTANT: Regardless, when a detector goes into alarm,
always take appropriate action. Never ignore or dismiss an
alarm.
Refer to this information about the different alarm types
and their corresponding screens.
Alarm Type Description Screen
Low Alarm
Slow siren (upward tone)
Slow flash
Black box around gas
flashes
Vibrator alarm activates
High Alarm
Fast siren (downward
tone)
Fast flash
Black box around gas
flashes
Vibrator alarm flashes
Time
Weighted
Average
(TWA) Alarm
Fast siren (downward
tone)
Fast flash
Black box around gas
flashes
Vibrator alarm activates
Short Term
Exposure
Limit (STEL)
Alarm
Fast siren (downward
tone)
Fast flash
Black box around gas
flashes
Vibrator alarm activates
Multi Alarm
Alternating low and high
alarm
Black box around gas
flashes
Type of alarm alternates
Vibrator alarm alternates
Sensor
Failure
Alarm Îis displayed
Alarm Type Description Screen
Over Limit
(OL) Alarm
Fast siren (downward
tone)
Fast flash
Black box around gas
flashes
Vibrator alarm activates
Sequence of alternating
beeps and alternating
flashes
Normal
Deactivation
Vibrator alarm activates
Countdown initiates
“OFF” is displayed
Sequence of 10 rapid
sirens and alternating
flashes followed by
7 seconds of silence
(continues for 15
minutes)
Low Battery
Alarm
flashes
Vibrator alarm pulses
After 15 minutes of
the low battery alarm
sequence, the detector
will enter critical alarm
Critical
Battery
Alarm
Fifteen minutes after low
battery alarm activates,
sequence of 10 rapid
sirens and alternating
flashes with 1 second
of silence in between
(sequence reactivates
seven times)
Vibrator alarm pulses
“Low Battery Powering
Off” is displayed and the
detector deactivates
Pump Alarm Detector is in pump alarm when gas is turned off
during calibration.

BW Ultra User Manual6
Alternate Display Background
To activate its functionality:
1. Go to Instrument Operation Tab.
2. Check or uncheck the Normal Display box to activate or
deactivate the White Background.

BW Ultra User Manual 7
Detector Operations
Activate the detector
Turn-on the detector in a safe area with an atmosphere of
20.9% oxygen and free of hazardous gas.
1. For first time use, charge the battery for up to 8 hours
or until LED light turns green using the charging
adapter provided. Refer to Charge the battery for more
information.
2. Press and hold the button for three seconds.
3. For first time use, a Warming sensors message is
displayed and a 30 minutes countdown is displayed.
In most cases, this countdown only lasts a couple of
minutes.
4. When the detector displays Pump test Block inlet,
block the pump inlet with a finger, and then after a
couple of seconds unblock the pump inlet.
The detector performs a quick pump test. A Pump Test
passed message is displayed.
If you do not block the pump inlet, the detector will turn
off after two minutes.
The detector will then perform a self-test, including
testing the sensors. This process could take several
minutes.
If necessary, you will be instructed by screen prompts to
calibrate newly-installed sensors.
5. When the self-test is complete, press and hold the
button to zero sensors. After the autozero is complete,
the detector then checks the sensors for calibration and
bump test.
If the detector identifies sensors requiring calibration or
bump testing, press the button and follow the on-screen
instructions.
Activate the backlight
To activate the backlight on the screen, press the button.
Deactivate the detector
1. Press and hold the button during the powering-off
countdown.
2. Release the button when OFF is displayed.
Navigate the menu
There are four main menu items.
•See Information
•Start Bump Test
•Zero Sensors
•Start Calibration
1. Double pressing the button displays all four options on
the screen. See Information is selected and highlighted
by default.
2. Press the button to transition the selection to the next
choice.
3. Press and hold for three seconds to enter the selected
option.
4. Follow on-screen instructions for your selected
operation. Most of the detector’s procedures are
described in this guide.
View detector’s general information
1. Double-press the button to enter the main menu.
2. Select See information and press the button to scroll
through the following information:
Peak readings
STEL readings
TWA readings
Bump test intervals
Calibration
BLE information (BLE should be enabled)
LEL Correction Factor
Low Alam setpoint
Pairing Code
Hi Alam setpoints
STEL setpoints
TWA setpoints
Reset TWA or STEL readings
Before you begin.
You need to enable TWA/STEL Reset in Safety Suite Device
Configurator to reset readings in the detector.
1. Go to the main menu and select > See Information >
TWA readings or STEL readings.
2. Press and hold for 3 seconds to reset readings.
A reset message is displayed.
Reset Peak readings
Before you begin.
You need to enable Peak Reset in Safety Suite Device
Configurator to reset readings in the detector.
1. Go to the main menu and select > See Information >
Peak readings.
2. Select Hold to reset peak readings. Press and hold for 3
seconds to reset readings.

BW Ultra User Manual8
Reset TWA/STEL and Peak readings
Before you begin.
You need to enable TWA/STEL Reset and Peak Reset in
Safety Suite Device Configurator to reset readings in the
detector.
1. Go to the main menu and select > See Information >
Peak readings.
2. Select Hold to reset all readings. Press and hold for 3
seconds to reset readings.
Zero sensors
Before you begin.
Connect the Nitrogen if this is a CO unit.
1. Go to the main menu and select Zero Sensors.
2. Press and hold for 3 seconds.
A Zeroing process starts automatically.
The screen displays all current gas measurements,
highlighting entries above zero.
Ambient air is applied to zero all sensors that are not CO.
The screen displays all current gas measurements,
highlighting entries being reset to zero.
3. If you are not zeroing O, Click NO in the prompted
message: Is this a CO unit?.
Zero results are displayed.
Press the button or wait for six seconds to end the
Zeroing process.
4. Click Yes if this is a CO unit and you want to apply
Nitrogen to zero CO.
A two minutes gas measure process starts automatically.
All current gas measurements and entries reset to zero
are displayed.
5. Turn off the gas following on-screen instructions.
Zero results are displayed.
6. Press the button or wait for six seconds to end the
Zeroing process.
Zero results are displayed as follows:
•A check mark for sensors that passed Zero
•A cross mark for sensors that failed Zero
•An exclamation mark for sensors that skipped Zero
Acknowledge alarms and messages
Press and release the button to perform any of the following:
•To acknowledge a latching alarm
•To acknowledge a low alarm
•To acknowledge due today message (for example, calibration and bump test
reminders). Note that the force calibration and force bump test features cannot
be bypassed.
Latching Alarms
If enabled, during an alarm condition the Latching Alarms
option causes the low and high gas alarms (audible, visual,
and vibrator) to persist until the alarm is acknowledged and
the gas concentration is below the low alarm setpoint. The
LCD displays the peak concentration until the alarm no
longer exists. Local regulations in your region may require
the Latching Alarms option be enabled.
The detector is shipped with the Latching Alarms option
disabled.
Calibrate the detector
Perform a calibration to adjust the sensitivity levels of
sensors and ensure accurate responses to gases.
The detector can be calibrated in two ways:
•Apply gas from a cylinder to the sensors manually through the pump inlet.
•Use an IntelliDoX module.
Before you begin. Move to a normal atmosphere (20.9%
v/v O) that is free of hazardous gas.
1. Go to the main menu and select > Start Calibration.
2. Press and hold the button for three seconds to display
the Powering Off countdown and continue to hold for
the Starting Calibration countdown.
The detector will enter the zero function. The Zeroing
process starts automatically and lasts for five minutes.
Current gas measurements are displayed, and entries
above zero are highlighted.
3. Connect the calibration hose to the pump inlet. Make
sure to use a demand flow regulator.
4. Confirm that you want to apply Nitrogen to zero CO.
5. When Apply calibration gas now is displayed,
apply the gas and wait for a maximum of five minutes.
The detector first tests for a specific type of gas. When
it detects enough of that gas for sensor calibration, a
check box will be displayed next to that gas. Calibration
then begins. Gas values will adjust on the screen during
the calibration.
6. When Turn gas o is displayed, disconnect the device
from gas. Check marks will be displayed next to the
calibrated sensors. These sensors reset to the number
of days until the next calibration is due (for example,
180 days).
The calibration cycle will take about two minutes after
which the user will be prompted to Press button to
continue.
7. If the calibration was successful, Calibration
Passed will be displayed. Press the button to exit
calibration.
If the calibration failed for some or all of the gases,
either a Cal Error All gases applied mixed
results message (if the detector was not successfully

BW Ultra User Manual 9
calibrated for all gases) or a Fail all gases message
will be displayed. After the button is pressed, a Cal
overdue message will be displayed.
NOTE 1: After a Chlorine (Cl ) Sensor is installed in the BW Ultra
and it is configured in the device, a manual calibration for Clmust
be performed in order to complete the set-up process in the gas
detector. Further calibration cycles of Clcan be done using IntelliDox.
For BW Ultra sticky gases CL, NO, and HCN calibration is available
in all bays. For Ammonia (NH) the calibration is available. However,
it requires a wait period of 15 minutes between calibrations and all
the nests used in gang should be for BW Ultra. If it is not the case, it
is highly recommended to perform calibration for NHonly on the
first bay. For this reason, when NH, Ammonia is set on bays 2 to 5 a
warning will be displayed as . Other sticky gases not mentioned
here are not available to be calibrated for BW Ultra using IntelliDox.
NOTE 2: In 1.024 Firmware Version the COir can be caligrated along
with the quad gas mixtire using a 5 gas combination. If calibration
is skipped once, all gases will be skipped, and calibration failure will
be flagged.
NOTE 3: SOCalibration and / or quad gas cannot be individually
skipped.
Select PID Correction Factor
1. Once the instrument is connected to Safety Suite
Device Configurator (SSDC),select the instrument.
2. Choose the Sensor Tab.
3. Use the dropdown menu to select the correction factor.
4. Select Save.
5. Once Safety Suite Device Configurator (SSDC) has sent
the correction factor to the instrument, unplug instrument
from computer.
Start a Bump Test
Perform a bump test regularly to test sensors and alarms.
To bump test, expose the sensors to a gas concentration
that exceeds alarm setpoints and confirm that the sensors
and alarms work correctly.
The detector can be bump tested in two ways:
•Apply gas from a cylinder to the sensors manually through the pump inlet.
•Use an IntelliDoX module.
Perform a manual bump test
Before you begin.
Connect the calibration hose to a demand flow regulator on
the gas cylinder.Double-press the button and select > Start
Bump test.
8. Press and Hold the button for three seconds.
The detector displays Starting Bump test.
Bump test started is displayed, and then the
detector makes noise, flash, and vibrate.
9. The detector will prompt you Did you see and hear
the alarms?, select Pass, and Press and hold for
three seconds to confirm that the visual, audible, and
vibrator alarms work correctly.
An Audio-Visual test passed message is
displayed.
Skip to Step 5.
10. If the visual, audible, and vibrator alarms failed, select
Fail, and press and hold the button. An Audio-Visual
test failed message is displayed.
Then you can:
a) Apply gas, Skip to Step 5
b) Press the button to skip gas application and follow
on-screen instructions to end the Bump Test.
Bump test results are displayed, and the test ends.
11. If you want to apply gas, follow on-screen instructions.
Wait for about 30 seconds; gas measurements are
displayed for each pertinent gas sensor.
A Bump Test pass confirmation is displayed.
12. After the Turn gas o message is displayed, remove
the hose from the pump inlet. The detector will remain
in alarm until the gas clears from the sensors.
Bump test results are displayed showing check marks
next to the tested sensors. These sensors reset to the
number of days until the next Bump Test is due.
13. Press the button to finish the procedure.
aCAUTION
Honeywell recommends to bump test the sensors before each day’s
use to confirm their ability to respond to gas by exposing the sensors
to a gas concentration that exceeds the alarm setpoints.
Set up IntelliFlash
The IntelliFlash®feature causes the detector, if it is in
compliance (for example, bump tested and calibrated),
to flash a green light every second (the factory setting
default) from the top visual alarm indicator. In Safety Suite
Device Configurator, use the IntelliFlash Interval option to
change how often the detector flashes.

BW Ultra User Manual10
Set up Reverse IntelliFlash
IntelliFlash flashes a green light when the detector is in
compliance, but Reverse IntelliFlash®flashes an amber
light when the detector is not in compliance (a bump test
or calibration is overdue, or a sensor is not working and has
been overridden).
Use Safety Suite Device Configurator to change how often
the detector flashes for Reverse IntelliFlash.
IntelliFlash and Reverse IntelliFlash can be configured in
one of four scenarios:
Scenario 1
When both IntelliFlash and Reverse IntelliFlash are
enabled, the detector’s green LED will flash until it goes
out of compliance, then its amber LED will flash instead.
Scenario 2
If IntelliFlash is enabled and Reverse IntelliFlash is
disabled, the detector’s green LED flashes until it goes out
of compliance, then it stops flashing.
Scenario 3
If IntelliFlash is disabled and Reverse IntelliFlash is
enabled, neither LED will flash while the detector is in
compliance. The amber LED will flash if it goes out of
compliance.
Scenario 4
When both IntelliFlash and Reverse IntelliFlash are
disabled, neither LED will flash under any circumstances.
Set up the Confidence and Compli-
ance Beep interval
The Confidence Compliance Beep is a sound that tells
the user the detector is in compliance (for example, bump
tested and calibrated). In Safety Suite Device Configurator
use the Confidence/Compliance Beep option to change
how often the detector beeps for Confidence Compliance
Beep.
Select an operation mode
The detector can be used in one of three modes: Essentials
mode, Hole Watch mode, and Inert mode.
Note: Honeywell BW™ Ultra always monitors gas levels, regardless of
the operating mode. If the detector detects a sudden gas exposure,
it will flash, vibrate, and produce a loud siren noise. A gas level alarm
takes precedence over all of the detector’s other functions.
Essentials mode
The detector only shows the gas readings.
Hole Watch mode
The Hole Watch mode is the default operating mode. It is
used for confined space monitoring. Use Hole Watch mode
to monitor all gas levels in the same screen view. Hole
Watch mode uses bar graphs that fill when the detector
detects rising gas concentrations.
•Whenthedetectordetectsnormalgaslevels,HoleWatchmodedisplaysempty
bargraphs.Whenthedetectordetectsnon-criticalgaslevels,HoleWatchmode
displays filling bar graphs.
•When the detector activates a single gas alarm, Hole Watch mode highlights
the detected gas level for that gas in a solid bar.
•Whenthedetectoractivatesamultiplegasalarm,HoleWatchmodecontinues
to display the first detected gas level, as well as highlight other detected gas
levels in a solid bar.
•For oxygen, Hole Watch mode displays low and high levels in a bar graph. As
the detector detects a low oxygen level, the bar graph fills toward LO.
•As the detector detects a high oxygen level, the bar graph fills toward HI.
Inert mode
You can configure Inert Mode in Safety Suite Device
Configurator. The threshold for operation is 5%. If oxygen
readingsfallbelow5%,thedetectorpromptstheusertoenter
the Inert mode. The detector does not start automatically in
Inert Mode.
WhenthedetectorgoesintoInertMode, thealarmssetpoint
getactivated.IfthedetectordoesnotenterinInertmode,The
O readings are considered normal.
The inert mode operation:
1. Inert mode should be enabled in the configuration
2. When the Oconcentration becomes < 5 %vol for more
than 20 sec, a message will pop up on LCD to activate inert
mode, user has to press and hold for 3 secs.
3. Now inert mode is activated. and default inert mode low
alarm set point is 5%vol and high alarm set point is 5%vol.
4.To come backtonormalmode, when theOconcentration
becomes>18%volformorethan20sec,a messagewill pop
up on LCD to activate normal mode, user has to press and
hold for 3 secs.
5. Then normal mode is activated.

BW Ultra User Manual 11
one location.
Connect With IntelliDoX
If a detector’s calibration is overdue and the forced
calibration feature is enabled, the calibration can be
performed with an IntelliDoX docking station or through
the calibration option from the detector’s main menu.
Connect With an IR Link
The detector can be paired with an IR link, aka dongle.
There is an IR connection at the bottom of the detector that
allows Safety Suite Device Configurator configurations to
be efficiently transferred to multiple detectors. The IR link
will also allownew firmware to be transferred to detectors
or data/event logs to be transferred to Safety Suite Device
Configurator.
Note: You should have the IR Connectivity Kit (sold separately) to
transfer the data from a computer to the detector.
Configure the Detector
You can configure the Honeywell BW™ Ultra detector’s
device and sensor using Safety Suite Device Configurator.
Necessary to configure detector settings:
•Honeywell BW™ Ultra detector
•IR Link adapter or IntelliDoX docking station
•Computer with Safety Suite Device Configurator software installed.
For device settings, a startup message can be added;
Confidence Compliance Beep can be activated, bump tests
can be forced, stealth mode can be enabled, etc.
For sensor settings, the calibration gas type and frequency
can be changed, the bump test interval and alarm setpoints
can be set, STEL and TWA can be selected, etc.
You can perform some other calibrations with Safety Suite
Device Configurator.
• Latching Alarms
• IntelliFlash Mode
• IntelliFlash Interval (seconds)
• Confidence/Compliance Beep
• Confidence/Compliance Beep Interval (seconds)
• Datalog Interval (seconds)
• Language
• Hole Watch Mode
• Disable Button Power Off
• Time Zone/Time Settings. (Time Zone and UTC offset in
minutes)
• LEL over span ( as it is used by both whittle LEL & IR LEL)
• STEL / TWA back up
• Clear Peaks Type
• BLE enable
• Normal display
• Pairing Code
General Sensor Settings (for all sensors)
• Sensor Enable/Disable
• Calibration Gas Concentration
Note: When the operator configures the Honeywell BW™ Ultra using
Safety Suite Device Configurator, Honeywell strongly recommends
reviewing the detector’s settings before the operation to ensure that
settings were applied successfully and comply with performance
requirements.
Custom configuration created in Safety Suite Device
Configurator can be used to configure detector settings.
Example: Five detectors must have the same bump test
reminders and alarm setpoints. Each detector could be
configured separately or Safety Suite Device Configurator
can be utilized to create a custom settings configuration.
This configuration can then be loaded on each detector.
This saves time and allows settings to be managed from

BW Ultra User Manual12
Bluetooth Pairing
The user can pair the Honeywell BW™ Ultra to a mobile
device via built in Bluetooth Low Energy (BLE). The
Honeywell Safety Communicator app, installed on the
mobile phone, can then show gas readings and alarms from
the Honeywell BW™ Ultra unit that is connected. Readings
and alarms can then be sent to Honeywell’s remote
monitoring software.
1. Open de Device Configurator APP.
2. Select Device List.
3. Scan for Instruments.
4. Select the detector and then enter the detector's 100000
pairing code used by default by the BW Ultra.
Note: Pairing is not allowed at start up, during calibration, or bump test.
Warning: Wireless communication and infrastructure
should be used as informational monitoring only.
Replace a Sensor
Use only sensors designed by Honeywell for the
Honeywell BW™ Ultra detectors. Replace the sensors in a
non-hazardous location.
The Honeywell BW™ Ultra detector can be configured for a
maximum of 5 gases and may contain dummy sensors.
If an HCN is set up on the 5th, after cal/bump, the device
enters to high alarm (HCN) this is due to high cross
sensitivity. The type of sensor can only be configured at
factory during assembly process.
Due to above, the user request a BW Ultra with a dummy
sensor in the Analog sensor position, then this dummy
position will not be able to configure and install an analog
sensor. This will prevent that a wrong sensor type can be
installed in the device
Review Logs
Many of the detector events are logged and can be reviewed
via IntelliDoX or BLE. Typical logged events would be:
•bump test failed •self-test failed
•last calibration failed •calibration overdue
•calibration forced •calibration canceled
•calibration error •calibration passed
•sensors in alarm •system reset
•sensors zeroed • event logs vs. data logs
•“Turn cal gas off...” message is displayed
Maintenance
Maintenance
Perform the following tasks to maintain the detector in
good operating condition:
•Calibrate, bump test, and inspect the detector on a regular schedule.
•Maintain an operations log of all maintenance, bump tests, calibrations, and
alarm events.
•Keep the exterior of the detector clean.
Gas Cylinder Guidelines
•Usea premium-grade calibration gas thatis approved by theNational Institute
of Standards and Technology.
•Verify the expiration date on the cylinder before use.
•Do not use an expired gas cylinder.
•Contact Honeywell if a certified calibration of the detector is required.
Charge the Battery
You can charge the battery using the provided charging
adapter, that is certified for SELV/LVLC (isolated) with an
output Um of 6.3 V.
It can take up to 8 hours to get the battery fully charged in
a temperature range from 5 °C to 35 °C.
Note: If you charge with the power on, charging may not be completed
within 8 hours.
Maintain the Battery
Lithium-ion batteries do not respond well to cycles of full
discharge followed by a full charging cycle. Recharge the
battery before it is exhausted.
Do not charge the battery at low or elevated temperatures.
30°C (86ºF) is considered an elevated temperature and
should be avoided whenever possible.
A rechargeable battery’s runtime decreases approximately
20% over a two-year period of typical use.
Real Time Clock Display
The real time clock is displayed in the upper left corner
of the detector’s screen. It is configurable through Safety
Suite Device Configurator in 12 or 24-hour formats.
The date display can also be configured in several formats
through Safety Suite Device Configurator.
The time/date information is retained even when the
detector’s battery is being changed.

BW Ultra User Manual 13
Languages
Honeywell BW™ Ultra supports six languages: English,
French, German, Portuguese, Spanish, Simplified Chinese.
These are configurable through Safety Suite Device
Configurator.
Custom startup text can be entered in all languages
except Simplified Chinese through Safety Suite Device
Configurator.
Clean the Detector
Clean the exterior of the detector with a soft, damp cloth.
Use only water-based (non-alcohol) cleaners. Do not use
soaps, solvents, or polishes.
Upgrade the Firmware
Upgrade the Firmware via IR Link using the Safety Suite
Device Configurator.
Before you begin.
• Youshouldhave the IR Connectivity Kit (soldseparately)totransferthedata
from a computer to the detector.
Note: If connected to the Internet, Safety Suite DC or Safety Suite
DM provides the latest firmware automatically. If not connected to
the internet, click on Update and manually add the latest firmware
from Honeywell official website: sps.honeywell.com/us/en/software
• Download Safety Suite Device Confirator from the website here: https://
sps.honeywell.com/us/en/software/safety/connected-safety/safety-
suite/safety-suite-device-configurator#download and install.
• For more information refer to the Safety Suite User Guide
Safety Suite Device Configurator - Online upgrade (Having Internet service)
Option 1
1. Turn on the detector.
2. Go to the Device Inventory/List and click on the Refresh
button to see the connected devices.
3. Enable the checkbox next to the device serial number
and above a blue toolbar will appear.
4. Select the Update firmware button.
5. Follow the status of the process on the Notifications
queue.
6. Once the message 'Firmware Updated' appears on
the top, click on the Refresh button again to see the new
firmware version on the devices list.
Option 2
1. Turn on the detector.
2. Go to the Device Inventory/List and click on the Refresh
button to see the connected devices.
3. Click over the device serial number.
4. Click the Update button on the Device Details screen
below the Firmware Version section.
5. Follow the status of the process on the Notifications
queue.
6. The page is refreshed and the new firmware version is
listed.
Safety Suite Device Configurator - Offline upgrade
(use this option if you wish to refresh the firmware or
downgrade the firmware)
This option can be activated in two ways:
1. Having a computer with no internet access or
2. Enabling the Firmware updates using local file option
(Settings -> System Settings -> Local Settings) Settings.
pngimage.png
Firmware should be gotten under RFP format (this format
belongs to Safety Suite Device Configurator), you can get
the file by clicking on the following link:
Gas Detection Software and Firmware site
For the units:
1. Go to the Device Inventory/List and click on the
Refresh button to see the connected devices.
2. There are two ways to select the firmware file:
a. Enable the checkbox next to the device serial number
and above a blue toolbar will appear, select the Update
firmware button
b. Click on the device serial number to open the Device
Details.
3. Click the Update button below the Firmware Version
section,
4. Select the RFP file to use and click on the Update
button.
5. Follow the status of the process on the Notifications
queue.
6. Once the message Firmware updated appears on the
top, click on the Refresh button again to see the new
firmware version on the devices list.
Firmware Downgrade
For equipment having whittle SO2 sensor with Firmware
version 1.024.
It is not possible to downgrade to Version 1.018, since
this version is not capable to handle the SO2 sensor.

BW Ultra User Manual14
Appendices
Auto detect gas
While the gas is applied during calibration, the detector will
wait for up to 300 seconds to allow the gas to stabilize. If
the gas has not stabilized by then, the detector will display
a Gas unstable message. If the gas stabilizes within
300 seconds, it will be automatically detected and will not
have to be selected from a menu. The name of the gas and
a Span calibration in progress message will be
displayed. If a quad gas mixture was used, the detector will
display the names of all four gases.
Gas Alarm Setpoints
Gas alarms are activated when detected gas
concentrations are above or below the user-defined
setpoints. The gas alarms are described as follows.
Alarm Condition
Low Toxics and combustibles: Ambient gas level
above low alarm setpoint.
Oxygen: Ambient gas level may be set above or
below 20.9% (or 20.8%).
High Toxics and combustibles: Ambient gas level
above high alarm setpoint.
Oxygen: Ambient gas level may be set above or
below 20.9% (or 20.8%).
TWA Toxics only: Accumulated value above the TWA
alarm setpoint.
STEL Toxics only: Accumulated value above the STEL
alarm setpoint.
Multi-gas Two or more gas alarm conditions
simultaneously.
Over Limit (OL) OL or OL displays when readings are above or
below the sensor detection range, respectively.
Sample Factory Alarm Setpoints
Following table lists alarm setpoints as defined by the US
Occupational Safety and Health Association (OSHA).
Gas TWA STEL Low High
HS 10 ppm 15 ppm 10 ppm 15 ppm
CO 35 ppm 50 ppm 35 ppm 200 ppm
O N/A N/A 19.5% vol. 23.5% vol.
LEL N/A N/A 10% LEL 20% LEL
Note: To disable an alarm, set the alarm setpoint to 0 (zero) in Safety
Suite Device Configurator..
Specifications
Detector dimensions: 8.1 x 14.6 x 5.1cm
Mass: 444.2 g
Operating temperatures: 4°F to +122°F (20°C to +50°C)
Battery operating times: 18 hours (14 hours with PID or
IR sensor) @ 4 °F / 20 °C
Rechargeable battery: 8 hours in a temperature range
from 5 °C to 35 °C.
Storage temperature: 40°F to +122°F (40°C to +50°C)
Operating humidity: 0% to 95% relative humidity
(non-condensing)
Detection range:
HS: 0 – 100 ppm (1 / 0.1 ppm increments)
CO: 0 – 2000 ppm (1 ppm increments)
O: 0 – 25% vol. (0.1% vol. increments)
SO: 0 - 100 ppm (0.1 ppm increments)
Combustible (LEL): 0% to 100% LEL (1% LEL
increments) or 0.0% to 5.0% v/v methane
Sensor type:
Alarm conditions: STEALTH, TWA alarm, STEL alarm, low
alarm, high alarm, multi-gas alarm, low battery alarm,
confidence beep, automatic deactivation alarm
Audible alarm: 95 dB at 30 cm (1 ft.) (100 dB typical)
variable pulsed beeper
Visual alarm: Red light-emitting diodes (LED)
Display: Alphanumeric liquid crystal display (LCD)
Screen resolution: 160X240 pixels.
Backlight: Activates when the pushbutton is pressed and
deactivates after 5 seconds; also activates during an alarm
condition
Self-test: Initiated upon activation.
Calibration: Automatic zero and automatic span.

BW Ultra User Manual 15
Standards and Certifications
The Honeywell BW™ Ultra gas detector is in conformity with
the following standards and certifications:
Approvals:
Approved by UL to both U.S. and Canadian Standards
UL 913, 8th Edition
UL 600790, 7th Edition
UL 600791, 7th Edition.
UL 6007911, 6th Edition
ANSI/ISA 60079291 (12.13.01) - 2013
CSA C22.2 No.152M1984 (R2016)
CSA C22.2 No. 600790:19
CSA C22.2 No. 6007911:14
CSA C22.2 No. 600791:16
UL: E480011
Class I, Division I, Group A, B, C and D, Temperature code
T4, 40 ≤ Tamb ≤ +50°C
Class I, Zone 0, AEx ia IIC T4 Ga, 40 ≤ Tamb ≤ +50°C
(without LEL and IR sensor installed)
Class I, Zone 0, AEx da ia IIC T4 Ga, 40 ≤ Tamb ≤ +50°C
(with LEL sensor installed and without IR sensor installed)
Class I, Zone 0, AEx ia IIC T4 Ga, 20°C ≤ Tamb ≤ +50°C
(with IR sensor installed and without LEL sensor installed)
Class I, Zone 0, AEx da ia IIC T4 Ga, 20°C ≤ Tamb ≤ +50°C
(with LEL and IR sensor installed)
CSA: E480011
Class I, Division I, Group A, B, C and D, Temperature code
T4, 40 ≤ Tamb ≤ +50°C
Ex ia IIC T4 Ga, 40 ≤ Tamb ≤ +50°C
(without LEL and IR sensor installed)
Ex da ia IIC T4 Ga, 40 ≤ Tamb ≤ +50°C
(with LEL sensor installed and without IR sensor installed)
Ex ia IIC T4 Ga, 20°C ≤ Tamb ≤ +50°C (with IR sensor
installed and without LEL sensor installed)
Ex da ia IIC T4 Ga, 20°C ≤ Tamb ≤ +50°C (with LEL and IR
sensor installed)
ATEX:DEMKO 18 ATEX 1833X
UKCA: UL21UKEX2006X
EN IEC 600790:2018
EN 6007911:2012
EN 600791:2014
EN 6007926:2015
I M1 Ex ia I Ma, 20°C ≤ Tamb ≤ +50°C
II 1 G Ex ia IIC T4 Ga, 40°C ≤ Tamb ≤ +50°C
(without LEL and IR sensor installed)
I M1 Ex da ia I Ma, 20°C ≤ Tamb ≤ +50°C
II 1 G Ex da ia IIC T4 Ga, 40°C ≤ Tamb ≤ +50°C
(with LEL sensor installed and without IR sensor installed)
I M1 Ex db ia I Ma, 20°C ≤ Tamb ≤ +50°C
II 2 G Ex db ia IIC T4 Gb, 20°C ≤ Tamb ≤ +50°C
(with IR sensor installed)
IECEx: UL 18.0061X
IEC 600790:2017
IEC 6007911:2011
IEC 600791:2014
IEC 6007926:2014
Ex ia I Ma, 20°C ≤ Tamb ≤ +50°C
Ex ia IIC T4 Ga, 40°C ≤ Tamb ≤ +50°C
(without LEL and IR sensor installed)
Ex da ia I Ma, 20°C ≤ Tamb ≤ +50°C
Ex da ia IIC T4 Ga, 40°C ≤ Tamb ≤ +50°C
(with LEL sensor installed and without IR sensor installed)
Ex db ia I Ma, 20°C ≤ Tamb ≤ +50°C
Ex db ia IIC T4 Gb, 20°C ≤ Tamb ≤ +50°C
(with IR sensor installed)
The following additional previous editions of Standards
noted under the “Standards” section of this Certificate were
applied to integral Components as itemized below. There are
no significant safety related changes between these previous
editions and the editions noted under the “Standards” section.
Product Certificate Num Standards
Dynament Ltd.
Gas Sensors Type
MSH2ia***
IECEx FTZU
15.0002U IEC 600790 Edition 2011
City Technology
Limited, Miniature
Combustible Gas
Sensor - 1 LEL 75
IECEx ULD
16.0016U IEC 600790 Edition 2011
JPEx
DEK21.0013X
JNIOSHTR461: 2015
JNIOSHTR466: 2015
Ex ia IIC T4 Ga, 40°C ≤ Tamb ≤ +50°C
(without LEL and IR sensor installed)
DEK21.0014X
JNIOSHTR461: 2015
JNIOSHTR462: 2018
JNIOSHTR466: 2015

BW Ultra User Manual
16
Ex da ia IIC T4 Ga, 40°C ≤ Tamb ≤ +50°C
(with LEL sensor installed and without IR sensor installed)
DEK21.0015X
JNIOSHTR461: 2015
JNIOSHTR462: 2018
JNIOSHTR466: 2015
Ex db ia IIC T4 Gb, 20°C ≤ Tamb ≤ +50°C
(with IR sensor installed)
FCC Compliance
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter. This
equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying RF
exposure compliance.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required
to correct the interference at his own expense.
CAUTION
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with FCC radiation exposure limits
set forth for an uncontrolled environment and meets the
FCC radio frequency (RF) Exposure Guidelines. This device
has very low levels of RF energy that it is deemed to comply
without maximum permissive exposure evaluation (MPE).
RED Compliance
Honeywell Analytics Asia Pacific Co., Ltd. hereby declares
that this gas detector, Honeywell BW™ Ultra, is in
compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada license-exempt
RSS. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
This device complies with FCC/ISED radiation exposure
limits set forth for an uncontrolled environment and meets
the FCC/ISED radio frequency (RF) Exposure Guidelines.
This device has very low levels of RF energy that it is
deemed to comply without maximum permissive exposure
evaluation (MPE).
Canada, avis d’Industrie Canada (IC)
Cet appareil est conforme aux normes RSS exemptes de
licence d’Industrie Canada. Son utilisation est soumise aux
deux conditions suivantes :
(1) cet appareil n’engendre pas d’interférences, et
(2) cet appareil doit tolérer tout type d’interférences,
notamment les interférences pouvant provoquer une
utilisation non désirée de l’appareil.
Cet équipement est conforme aux limites établies par FCC/
Industrie Canada en matière d’exposition aux radiations
dans un environnement non contrôlé. Cet équipement ne
doivent pas être colocalisés ou fonctionner en conjonction
avec tout autre antenne ou émetteur.
In terms of North America flammable gas performance
approval:
Honeywell BW™ Ultra is approved for ISA 60079291 and
CSA C22.2 No.152.
Only Honeywell BW™ Ultra catalytic bead flammable sensor
was evaluated for CSA C22.2 No.152 and ISA 60079291.
The evaluation is valid only with the pumping flow rate 300
ml/min, 3 m length tube and CH (Methane) gas.
The other options are not the scope of CSA C22.2 No.152
and ISA 60079291.
For the compliance of CSA C22.2 No.152 and ISA 60079
291, the adjustable alarm point shall not exceed 60 %
LEL and the highest alarm shall be configured as latching
alarm.
In ISA 60079291, Honeywell BW™ Ultra was tested only
for IP54. Other IP ratings are not the scope of ISA 60079
291. Honeywell BW™ Ultra was pressure tested for 80, 100
and 120 kPa in ISA 60079291. Outside of 80 - 120 kPa is
NOT the scope of ISA 60079291.

Sensor T90 Ratings
Please be advised of the following T90 ratings for the BW
Ultra sensors stated below:
Sensor Type T90 Ratings
LEL Sensor (1LEL75C) for Methane is < 20 sec @
20°C
Oxygen (O) Sensor: 1O2 for O is typically <15 sec
Carbon Monoxide (CO) Sensor: CO 4R+ for CO is < 30 sec
Hydrogen Sulfide (HS) Sensor: 1HS for HS is typically <30 sec
Nitric Oxide (NO) Sensor: NO 4R+ for NO is < 60 sec
Nitrogen Dioxide (NO) Sensor: NO 4R+ for NO is < 60 sec
Carbon Dioxide (CO) Sensor: NDIR 4R+ for CO is < 30 sec
Response Time (t90): The time for a sensor to reach 90% of
its final stable reading. Typically, an exposure of twice the
t90 time is required to get a stable reading. Response times
of sensors and instruments may be different. The response
timeofinstrumentisdependentonsensorresponsetimeand
testconditionslikecalibrationgasflowrate,temperatureetc.
Specifications are valid at 20°C, 50% RH, and 1013
mBar, using Honeywell recommended circuitry.
Performance characteristics outline the performance
of sensors supplied within the first three months.
Output signal can drift below the lower limit over time.