Honeywell GW-1000-WE User manual

MOUNTING INSTRUCTIONS
Gateway
GW-1000-WE/GW-1000-NWE
SUPPORTED DOCUMENTS
• 31-00424 (Gateway Datasheet)
• 31-00426 (Gateway Installation Guide)
EKeep these instructions together with the
device or with the equipment
documentation! Only qualified personnel
may perform electrical connections for 230
VAC.
FCette instruction est à conserver avec le
contrôleur ou avec la documentation de
l'installation ! Le raccordement électrique
pour le 230 VAC ne peut être effectué
que par le personnel autorisé.
PGuarde estas instruςões junto do regulador
ou junto da documentaςão da instalaςão! A
ligaςão eléctrica a 230 VAC só deve ser
efectuada por pessoal especializado.
DDiese Anleitung ist beim Gerät oder in der
Anlagendokumentation aufzubewahren!
Elektrisches Anschließen von 230 VAC ist
nur durch autorisiertes Fachpersonal
gestattet.
IQueste istruzioni devono essere
conservate insieme al lettore o con la
documentazione dell´impianto! I
collegamenti a 230VCA devono essere
eseguiti da personale qualificato.
SDenna instruktion skall förvaras tillsammans
med regler eller
anläggningsdokumentationen! Elektrisk
anslutning med 230 VAC får endast utföras
av behörig personal.
DK Opbevar denne vejledning sammen med
regler eller med anlægsdokumentationen!
Elektrisk tilslutning for 230 VAC bør kun
foretages af autoriserede personer.
NDenne veiledningen skal oppbevares
sammen med regler eller
anleggsdokumentasjonen! Elektrisk
tilkopling med 230 VAC må kun utføres
av fagfolk.
FI Tätä ohjetta tulee säilyttää laitteen
läheisyydessä tai yhdessä muiden
dokumenttien kanssa! Vain asianmukaiset
oikeudet omaava henkilö saa suorittaa 230
VAC käyttöjännitteen liitäntätöitä.
ES Conserve estas instrucciones con el recalar
o con la documentación de la instalación.
La conexión eléctrica a 230 VCA debe
hacerse solamente por personal
qualificado.
NL Deze handleiding moet bij de regelaar, of
met de documentatie van de installatie
worden bewaard! De elektrische
aansluiting voor 230 VAC mag alleen door
geautoriseerd personeel worden
uitgevoerd.
PL Instrukcję obsługi należy przechowywać
przy urządzeniu albo w dokumentacji
technicznej. Tylko autoryzowany servis jest
upoważniony do podłączenia do 230 VAT.
SC 请将此装配说明书与设备或者与设备的其
他文档保存在一起！ 230 V 交流电的接线
操作仅允许由合格的专业人员执行
TC 請將此裝配說明書與設備或者與設備的
其他文件儲存在一起！
僅能由合格的專業人員進行230 V交流
電的接線作業。
K본 설치 설명서를 해당 장치 또는 관련
문서와 함께 보관하시기 바랍니다.
230VAC 전원 연결은 관련 작업 전문가에
의해 수행되어야 합니다.

GW-1000-WE / GW-1000-NWE GATEWAY
31-00425 | Rev.10-20
Part Number: 32348979-001 2
WARNING
Electrical Shock Hazard.
Can cause severe injury, death or property
damage.
Disconnect the power supply before beginning
installation to prevent electrical shock and
equipment damage. More than one power supply
may have to be disconnected.
When Installing This Product
1. Read these instructions carefully. Failure to follow
them could damage the product or cause a hazard-
ous condition.
2. Check the ratings given in the instructions and
marked on the product to make sure the product is
suitable for your application.
3. Installer must be a trained, experienced service tech-
nician.
4. After installation is complete, check the product
operation.
5. Be sure wiring complies with all applicable codes,
ordinances and regulations.
Regulation (EC) No 1907/2006
According to Article 33 of REACH Regulation, be informed
that this product may contain components with lead (CAS:
7439-92-1) content above the threshold level of 0.1% by
weight.
INTRODUCTION
This document contains mounting instructions for GW-
1000-WE and GW-1000-NWE Gateways and its
accessories. These Gateways can be mounted on the wall,
panel, and DIN rail.
Mounting the Gateway on a
Wall/Panel Using DIN Rail
1. Mount the DIN rail on the wall/panel by using screws.
2. Remove the bottom Terminal Cover from the Gate-
way. Use your fingers to push the cover upwards as
shown in the below figure.
3. Remove the top Terminal Cover as described in the
previous step.
4. Hold the Gateway in an orientation such that the red
clip is facing downwards and towards the DIN rail.
WEEE
WEEE Directive 2012/19/EC Waste
Electrical and Electronic Equipment
Directive
• At the end of the product life,
dispose of the packaging and
product in an appropriate recycling
center.
• Do not dispose of the device with
the usual domestic refuse.
• Do not burn the device.
Screw
Panel/Wall
DIN Rail
Terminal Cover
(Bottom side)
Up Arrow
GW-1000-NWE
Gateway
DIN Rail
Red Clip
POWER
RS485
CH2-
FGND
+

GW-1000-WE / GW-1000-NWE GATEWAY
3 31-00425 | Rev.10-20
Part Number: 32348979-001
5. Tilt the Gateway as shown in the below figure.
6. Mount the top side of the Gateway on the DIN rail and
then push the bottom side of the Gateway until the
red clip on the Gateway clamps with the DIN rail.
7. Connect the terminal wires, Ethernet cables, and
antenna (if applicable). For antenna installation, see
the “Antenna” section.
8. Re-mount the terminal covers.
Mounting the Gateway on a
Wall/Panel Using Screws
1. Remove the bottom Terminal Cover from the Gate-
way. Use your fingers to push the cover upwards as
shown in the below figure.
2. Remove the top Terminal Cover as described in the
previous step.
3. Extend all the screw clips on the Gateway by placing a
flat blade screwdriver on the slot as shown and slide
out.
4. Hold the Gateway along the wall and mark four drill-
ing locations through the higher point of the screw
clip slots as shown in the below figure.
5. Remove the Gateway from the wall and drill four
holes at the marked locations.
6. Insert anchors into the four mounting screw holes.
7. Hold the Gateway along with the wall/panel so that
the holes are aligned.
8. Insert the screws into the topside holes first and fas-
ten them with a screwdriver.
NOTE: It is recommended to use the 6-18 1” pan head
Phillips tapping screws.
9. Insert the screws into the bottom holes and fasten
them with a screwdriver.
10. Connect the terminal wires, Ethernet cables, and
antenna (if applicable). For antenna installation, see
the “Antenna” section.
11. Replace the Terminal Cover or install the Extended
Terminal Cover (for more information, see the
“Extended Terminal Cover” section).
Red Clip
DIN Rail
FGND
0
~
GND
-
+
FGND
0
~
GND
-
+
Terminal Cover
(Bottom side)
Up Arrow
GW-1000-NWE
Flat Blade
Screwdriver
Screw Clip
Insertion Point
Gateway
Marking Location
Screw
Panel/Wall
Controller
Anchor
POWER
RS485
GND2
CH3+
-

GW-1000-WE / GW-1000-NWE GATEWAY
31-00425 | Rev.10-20
Part Number: 32348979-001 4
Extended Terminal Cover
Extended Terminal Covers are used for protecting the
Gateway terminals from being tampered and avoid human
contact when the Gateway is mounted on a wall/door.
These covers must be purchased separately.
Mounting Extended Terminal Covers
NOTE: The Extended Terminal Covers must be installed
only after completing the terminal wiring and the
antenna installation.
1. Place the upper Extended Terminal Cover on the top
side of the Gateway so that the rectangular slots of
the Gateway and the rectangular clip of the Extended
Terminal Cover are aligned.
2. Push the Extended Terminal Cover using both hands
until the cover firmly attached to the Gateway.
3. Repeat the step above to mount the lower Extended
Terminal Cover.
NOTE: To remove the Extended Terminal Cover, a flat
blade screwdriver is required. See the “Removing
Extended Terminal Covers” section for details.
Antenna
The connected devices can communicate with the Gateway
via Wi-Fi or Bluetooth connections. The Gateway kit
contains a Remote antenna that must be installed
manually on the Gateway. The Remote antenna has a cable
that connects to the Gateway, and the antenna is mounted
outside the panel/cabinet.
The Local antenna can be purchased separately, and it
mounts directly on the Gateway. The Local Antenna is only
used when the Gateway is wall mounted or mounted
outside of a panel/cabinet.
Installing the Local Antenna
1. Insert the antenna terminal end into the SMA con-
nector.
2. Tighten the antenna terminal nut by turning the nut
clockwise. Do not over tighten.
Installing the Remote Antenna
1. Place the Remote antenna where the signal reception
is good.
2. Route the Remote antenna wire terminal to the Gate-
way.
3. Insert the wire terminal into the SMA connector.
4. Tighten the wire terminal nut by turning the nut
clockwise. Do not overtighten.
REMOTE ANTENNA PLACEMENT
• Place and align the antenna in a way that the Wi-Fi
signal does not interfere with many obstacles.
• Obstacles such as metal, steel-reinforced concrete wall
filter ~10-90% of the Wi-Fi signal. Other obstacles such
as drywall, wood, glass filter ~0-10% of the Wi-Fi signal.
• The antenna has a strong signal transmission/reception
from the side. See the figure below. Position the sides of
the antenna towards the device it is communicating
with (e.g Smart IO/WiFi Node).
Extended Terminal
Cover
RS485
GND2
CH3+
FGND
-
Local Antenna
SMA Connector
Antenna Terminal
-NWE
SMA Connector
Remote Antenna
Wire Terminal
Ferrite
Ring
Smart IO/Wi-Fi Node
Smart IO/Wi-Fi Node
Smart IO/Wi-Fi Node

GW-1000-WE / GW-1000-NWE GATEWAY
5 31-00425 | Rev.10-20
Part Number: 32348979-001
• Keep the antenna away from devices that cause wireless
interference such as other Wi-Fi network and
telecommunications equipment.
• Make sure that the antenna is installed perpendicular to
the surface for a good Wi-Fi signal.
• Do not install the antenna close to the floor.
• The Local antenna can be used when the Gateway is
installed in a plastic cabinet/enclosure.
Installing Ferrite Ring
Ferrite ring is supplied with the kit. It must be installed on
the antenna wire somewhere between 10 to 30 cm from the
Gateway.
1. Lift the two locking tabs to open the ferrite ring.
2. Wind the wire three times as shown in the below fig-
ure.
3. Lock the Ferrite ring.
Removing the Extended Terminal
Covers
1. Insert a flat blade screwdriver into the rectangular
slot as shown in the below figure.
2. Use the flat blade screwdriver as a leaver, pull out the
top Extended Terminal Cover.
3. Repeat the steps above to remove the bottom
Extended Terminal Cover.
Removing the Gateway from the
DIN Rail
1. Remove the Terminal Covers if applicable.
2. Disconnect all the communication and power supply
terminals from the Gateway.
3. Uninstall the antenna by turning the antenna termi-
nal nut anticlockwise.
4. Hold the Gateway with one hand and insert a flat
blade screwdriver into the red clip slot.
5. Pull the red clip downward by using the flat blade
screwdriver.
6. After the Gateway is released from the DIN rail,
slightly tilt the Gateway on the horizontal axis, lift and
detach the Gateway from the DIN rail.
Surface
Surface
Ferrite Ring
Antenna Wire
Insertion slot
Extended Terminal
Cover
Flat Blade Screwdriver
-
FGND
0
~
GND
-
+
Flat Blade Screwdriver

GW-1000-WE / GW-1000-NWE GATEWAY
® U.S. Registered Trademark
© 2020 Honeywell International Inc.
31-00425 | Rev.10-20
Part Number: 32348979-001
Honeywell Building Solutions
Honeywell
715 Peachtree Street NE
Atlanta, GA 30308
customer.honeywell.com
buildingcontrols.honeywell.com
Removing the Gateway from the Wall/Panel
1. Remove the Extended Terminal Covers if applicable (see the Removing the Extended Terminal Cover section).
2. Disconnect all the communication and power supply terminals from the Gateway.
3. Disconnect the antenna by turning the antenna terminal nut anticlockwise.
4. Unscrew the bottom side screws first by using a screwdriver.
5. Hold the Gateway with one hand and unscrew the top side screws by using a screwdriver.
DIMENSIONS
122.4 mm
4.819"
106.7 mm
4.207"
59 mm
(2.323")
110 mm
(4.331")
45 mm
(1.772")
52 mm
(2.047")
135 mm
(5.315")
145.8 mm
(5.744")