Honeywell Lyric LCP300-L Installation and operating manual

LyricTM Gateway Installation and Reference Guide
Ref: LCP300-L/LCP300-LC
800-21666 10/16Rev. A

Lyric Gateway Installation and Reference Guide
- 2 -
RECOMMENDATIONS FOR PROPER PROTECTION
The Following Recommendations for the location of fire and burglary detection devices help provide proper
coverage for the protected premises.
Recommendations for Smoke and Heat Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations
contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.
•Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and
areas of the household as follows: For minimum protection a smoke detector should be installed outside of
each separate sleeping area, and on each additional floor of a multi-floor family living unit, including
basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not
normally recommended.
•For additional protection the NFPA recommends that you install heat or smoke detectors in the living room,
dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and
attached garages.
In addition, we recommend the following:
•Install a smoke detector inside every bedroom where a smoker sleeps.
•Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely
closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up
the sleeper if the door is closed.
•Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air
conditioners or humidifiers) are used.
•Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.
•Install smoke detectors in any room where an alarm control is located, or in any room where alarm control
connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room
could prevent the control from reporting a fire or an intrusion.
THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE
SOUNDING OF FIRE NOTIFICATION APPLIANCES.
Recommendations for Proper Intrusion Protection
•For proper intrusion coverage, sensors should be located at every possible point of entry to a home or
premises. This would include any skylights that may be present, and the upper windows in a multi-level
building.
•In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals
can be sent to the alarm monitoring station in the event that the communications are out of order (if
connected to an alarm monitoring station).
This Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with the
system. The security system is not designed for use with any device that may be attached to the system's control or other
communicating bus if Honeywell has not approved such device for use with the system. Use of any such unauthorized device
may cause damage or compromise the performance of the security system and affect the validity of the end user’s Honeywell
limited warranty. When you install devices that have been manufactured or approved by Honeywell, you give the end user
the assurance that these devices have been thoroughly tested to ensure optimum performance when used with this
Honeywell security system.

Lyric Gateway Installation and Reference Guide
- 3 -
Table of Contents
System Features............................................................................................................................................................................................ 5
Installing the Control....................................................................................................................................................................................7
Battery Installation..........................................................................................................................................................................................7
Battery Selection .....................................................................................................................................................................................7
Installing the Rechargeable Backup Battery.................................................................................................................................7
Replacing the Rechargeable Backup Battery...............................................................................................................................7
Wall Mounting.................................................................................................................................................................................................. 8
Desktop Mounting .......................................................................................................................................................................................... 9
Replace the Back Plate......................................................................................................................................................................... 9
Install the Desk Stand ........................................................................................................................................................................... 9
AC Power..........................................................................................................................................................................................................10
Wiring Overview ............................................................................................................................................................................................10
Make Electrical Connections .............................................................................................................................................................10
Communications Modules ...........................................................................................................................................................................11
Communications Module 24-Hour Standby power ...................................................................................................................11
Install and Configure Communications Module ..................................................................................................................................11
Installing the Cellular Module.............................................................................................................................................................11
Checking Signal Strength...................................................................................................................................................................12
Wireless Zones..............................................................................................................................................................................................13
General Information......................................................................................................................................................................................13
Zones..........................................................................................................................................................................................................13
Range .........................................................................................................................................................................................................13
Transmitters.............................................................................................................................................................................................13
House Identification..............................................................................................................................................................................13
Transmitter Supervision......................................................................................................................................................................13
Transmitter Input Types......................................................................................................................................................................13
Transmitter Battery Life......................................................................................................................................................................13
RF Transmitter Loop Numbers.........................................................................................................................................................14
Mechanics of Programming ....................................................................................................................................................................15
Navigating Menus ..........................................................................................................................................................................................15
Touch-screen Display...........................................................................................................................................................................15
Navigation Keys .....................................................................................................................................................................................16
Home Screen...........................................................................................................................................................................................16
Security Screen ......................................................................................................................................................................................17
Master User Tools Screen...................................................................................................................................................................17
Programming ..................................................................................................................................................................................................18
Enter Installer Programming Mode.................................................................................................................................................18
Loading Factory Defaults...........................................................................................................................................................................19
Select a Default Configuration .........................................................................................................................................................19
Exit Programming Mode .............................................................................................................................................................................19
Zone Response Type Definitions.........................................................................................................................................................20
General Information.....................................................................................................................................................................................20
System Operation.......................................................................................................................................................................................22
Key/Touchscreen Operation....................................................................................................................................................................22
Panic Key/Icons.............................................................................................................................................................................................22
Security Codes...............................................................................................................................................................................................22
Installer Code .........................................................................................................................................................................................22
Master Code ...........................................................................................................................................................................................22
Enter/Change the Master Code by Installer...............................................................................................................................22
Secondary User Codes .......................................................................................................................................................................22
Reset Master Code...............................................................................................................................................................................23
Security Code Notes ...........................................................................................................................................................................23
System Displays ............................................................................................................................................................................................24
Zone Status Displays...................................................................................................................................................................................24
Audio Alarm Verification (Two-Way Voice Feature) .....................................................................................................................25
Activation ................................................................................................................................................................................................25
Operator Commands ..........................................................................................................................................................................25
Event Log ........................................................................................................................................................................................................26
Contact ID Event Log Codes............................................................................................................................................................26
Central Station Messages ..........................................................................................................................................................................27
Testing the System ....................................................................................................................................................................................28

Lyric Gateway Installation and Reference Guide
- 4 -
Table of Contents (Continued)
Test Modes ......................................................................................................................................................................................................28
Testing the System.......................................................................................................................................................................................28
Armed System Test .....................................................................................................................................................................................28
Zone Discovery Mode .................................................................................................................................................................................29
Rebooting the System ................................................................................................................................................................................29
Programming Default Values ............................................................................................................................................................... 30
Zone Assignment/Alarm Response Type for Configuration 1 .....................................................................................................32
Zone Assignment/Alarm Response Type for Configuration 2 ....................................................................................................33
Zone Assignment/Alarm Response Type for Configuration 3 and 4 .......................................................................................34
Zone Response Type Matrix ..................................................................................................................................................................35
Regulatory Agency Statements...........................................................................................................................................................36
Limitations of this System Statement...............................................................................................................................................37
Agency Notices............................................................................................................................................................................................38
SIA Quick Reference Guide....................................................................................................................................................................39
Specifications................................................................................................................................................................................................39
Glossary ..........................................................................................................................................................................................................40
Contacting Technical Support...............................................................................................................................................................41
Index..................................................................................................................................................................................................................42
Summary of Connections Diagram.....................................................................................................................................................43
Warranty Information ............................................................................................................................................................ Rear Cover
Lyric™ Lock
This system supports Lyric Lock, an advanced feature designed to keep it functioning optimally. Lyric Lock
capabilities include: the ability to interact with Honeywell and your company’s network for the setup and
programming of system features, support for remote software updates and the ability (when enabled) to
enhance the end user’s security by preventing unauthorized takeover of the system by another monitoring
company.
In the event that the end user wishes to authorize another company to take over the system, the end user may
request that Honeywell remotely disable Lyric Lock. Honeywell will require documentation that the end user
has attempted to contact your company three times and that your company has failed to respond, or failed to
agree to the end user’s request.

Lyric Gateway Installation and Reference Guide
- 5 -
System Features
The Lyric Gateway is a self-contained, rechargeable wireless control/communicator that features easy
installation and usage. A built-in speaker provides voice annunciation of system status along with voice
descriptors of each zone. An internal module allows the controller to communicate with the Central Station via
the Internet or (if installed) Cellular Wireless.
ETL
Lyric Gateway is not intended for UL985 Household Fire applications unless a 24-hour backup
battery (p/n 300-03866-AIO) is installed.
System Features
• Message Center (for user recorded messages)
• Voice Announcement of System and Zone Status
• Ten User-selectable Chime Sounds
•Automatic Stay Arming
• Night Stay Arming
• 49 User Codes (Installer, Master, Guest, Duress)
• Panic Functions (Police, Fire, Medical)
• Programmable Reminders
•Video Camera Control (requires WiFi connection)
•Supports Mobile Devices (Tablet, iPAD, etc.) that duplicate functions of the Lyric Gateway (i.e.; Security,
Web Content Home Automation and Video Control)
Home Automation
• Integrated Z-Wave Support
• Control up to 72 Z-Wave Home Automation Devices including:
-
Thermostats (up to 8)
-
Door Locks (up to 6)
- Devices (outlets, switches, lamps/appliances) (up to 60)
-
Garage Doors (up to 4)
-
Water Valves (up to 4)
• Supports Z-Wave Network Wide Inclusion (NWI) Mode
• 100 programmable Smart Actions
•Up to 150 scheduled events
Zones and Devices
• 4 Panel Panic Zones
• 64 Wireless Zones (5800 and SiX™ Series transmitters)
• Four Garage Door Zones
•
32 Wireless Buttons (Wireless Key) Zones (5800 and SiX™ Series transmitters)
•
Eight (SiX™ Series) Wireless Keypad Zones
• 12 Temperature Zones
• Resident Monitor Zone Types
•Built-in Case Tamper
Communication
•ADEMCO Contact ID
•Integrated WiFi Support
• Cellular (GSM or CDMA) Central Station communication
• WiFi Central Station communication
• Ethernet Central Station communication
•Two-way Voice Communication
• Supports AlarmNet 360
TM
Remote Services

Lyric Gateway Installation and Reference Guide
- 6 -
System Features (Continued)
System Power
•Primary Power: Plug-in Power Supply, 110VAC to 9VDC, 2.5A output p/n 300-04705V1 (300-4063V1 in
Canada)
•Backup Battery: Rechargeable Nickel-metal Hydride Battery Pack rated at 7.2Vdc. (p/n 300-03864-AIO
or 300-03866-AIO
Alarm Output
• Built-in Sounder
• Steady Output for burglary/panic
•Temporal (3) Pulse Output for fire alarms
•
Temporal (4) Pulse Output for carbon monoxide alarms
• Audio Alarm Verification (AAV)
Programming
• Options stored in EEROM
•Can be uploaded, downloaded or controlled via AlarmNet 360
TM
using capable Cellular or WiFi
Communications Module
• Flash Downloading
Other Features
•Exit Error feature (detects difference between an actual alarm and exit alarm caused by leaving a door
open after the exit delay expires)
•Event Log Storage (total 6,000 events)
• RF Jam Detection
•Advanced Protection Logic™ (APL) (Minimizes the likelihood of the system being disabled before
notification can be sent to the Central Station indicating that the premises have been compromised.)
• Lyric™ Lock (Customer Retention Logic) Dealer selectable Lockout (anti-takeover) feature
•Dealer/Central Station Messages (requires Total Connect Service)

Lyric Controller Installation and Reference Guide
- 7 -
Installing the Gateway
Battery Installation
The Lyric Gateway is equipped with an integral, replaceable, rechargeable battery pack rated at 7.2Vdc. In the
event of an AC power loss, the system is supported by the long life backup battery that is supervised for
connection and for low voltage conditions. If the battery is missing, or a low battery condition is detected, a
“low battery” message is displayed on the smart device and “Alert” will flash red on the Gateway. In addition, a
System Low Battery report is sent to the Central Station. In addition, the system will beep once every 45
seconds to audibly indicate a low battery condition (press any key to stop the beeping). Select the appropriate
battery pack, based on the installation’s requirement, and install the battery pack. Follow the steps and refer to
the figure below to install and connect the battery.
Battery Selection
Select the appropriate battery pack, based on the installation’s requirement, and install the battery pack.
Battery Part Number
Battery StandbyTime
Low Battery Notification
300-03864-AIO
4-hours (minimum)
Approximately 1-hour before battery depletion
300-03866-AIO 24-hours (minimum) At least 1-hour before battery depletion
Replacing the Rechargeable Backup Battery
1. Insert the battery pack into gateway.
2. Close the hinged battery retainer.
3. Connect the battery pack connector to the receptacle on the gateway.
4. Align the slots on the back of the controller with the hooks on the rear cover/wall mount as shown below.
5. Once attached, insert the screw to secure the rear cover/wall mount.
6. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-up, the LEDs will flash
alternately.
7. When the power-up sequence is complete, the green Disarmed LED and the green shield will be lit.
Rechargeable batteries may take up to 48-hours to fully charge. The “Low Battery” message
should clear within four hours or by entering Test Mode.
Replacing the Rechargeable Backup Battery
1. When battery replacement is required, at the Master User Tools Menu screen select the “Advanced” icon.
2. Select “Install Backup Battery” and follow the displayed steps to replace the battery or follow the steps
below.
Remove the battery
1. Remove the screw securing the gateway to the rear cover/wall mount (if used).
2. Remove the back case or remove the gateway from the rear cover/wall mount.

Lyric Gateway Installation and Reference Guide
- 8 -
Installing the Gateway (Continued)
3. Disconnect the battery pack connector from the receptacle on the back of the gateway.
4. Open the hinged battery retainer.
5. Remove the battery pack from the Gateway.
Install the replacement battery
1. Install a replacement battery pack (LCP500-4B [p/n 300-03864-AIO] OR LCP500-24B [p/n 300-03866-
AIO]) into the gateway.
2. Close the hinged battery retainer.
3. Connect the battery pack connector to the receptacle on the gateway.
4. Align the slots on the back of the controller with the hooks on the rear cover/wall mount as shown below.
5. Once attached, insert the screw to secure the rear cover/wall mount.
6. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-up, the LEDs will flash
alternately.
7. When the power-up sequence is complete, the green Disarmed LED and the green shield will be lit.
NOTE: If a Cellular Communication Module is being installed, verify the module’s signal strength before
selecting a final mounting location. Refer to Checking the Signal Strength in the Communications
Module section.
Wall Mounting
NOTE: When selecting a location for the Lyric Controller, be sure to provide a separation of at least 10 feet
between 2.4GHz devices such as Wi-Fi Routers/Access Points.
For wall mounting follow the steps and refer to the figure below.
1. Feed the field wiring through the appropriate openings in the wall mount.
2. Attach the wall mount to a sturdy wall using the four provided screws.
3. If required, install an additional mounting screw in the case tamper.
4. Align the slots on the back of the controller with the hooks on the wall mount as shown below.
5. Once attached, insert the screw to secure the Lyric to the wall mount.

Lyric Gateway Installation and Reference Guide
- 9 -
Installing the Gateway (Continued)
Desktop Mounting
NOTE: When selecting a location for the Lyric Gateway, be sure to provide a separation of at least 10 feet
between 2.4GHz devices such as Wi-Fi Routers/Access Points.
The desk Stand can be installed in two positions that provide a viewing angle of 30 degrees or 60 degrees.
Follow the steps and refer to the figures below.
Install Desk Stand
1. Align the slots on the back of the gateway with the hooks on the desk stand as shown below.
2. Insert the stand into the slots on the rear case to provide the desired viewing angle and slide up to lock in
place.

Lyric Gateway Installation and Reference Guide
- 10 -
Installing the Control (Continued)
AC Power
The Lyric Gateway is powered by a 110VAC, 60 Hz/9 Volt DC, 2.5 Amp Plug-in Power Supply, 300-04705V1
(300-04063V1 in Canada). Refer to the wiring table below for wire gauge and length.
Use only the 300-04705V1 (300-04063V1 Canada) Power Supply. Do not plug the power supply
into the AC outlet until after all wiring connections have been made.
Wiring Overview
The following summarizes the electrical connections associated with the Lyric Gateway. Follow the steps and
refer to the figure below when making connections. Refer to the Summary of Connections diagram for
additional information.
Make Electrical Connections
1. Temporarily hang the controller from the hook on the wall mount.
2. Connect the male end of the receptacle on the Gateway.
3. Align the slots on the back of the Gateway with the hooks on the rear cover/mounting bracket.
4. Once attached, insert the screw to secure the Gateway to the rear cover/mounting bracket .
5. Connect the flying leads of the provided power supply cable to the + and – terminals on the power supply
(p/n 300-04705V1 or 300-04063V1).
6. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-up, the “System Standby!”
screen will be displayed.
WIRING TABLE
Maximum Distance Between
Power Supply and Controller
Wire Gauge
Up to 8 feet (2.44 m)
# 22
Up to 13 feet (3.96 m)
# 20
Up to 20 feet (6.1 m)
# 18

Lyric Gateway Installation and Reference Guide
- 11 -
Installing the Gateway (Continued)
The LYRIC-CDMA Communications Module is only available in the continental United States,
Alaska and Hawaii.
Communication Modules
The Lyric Gateway supports Central Station reporting using wireless/cellular and WiFi communications devices.
They also support upload/download programming capability via the Internet. This allows site maintenance
independent of Central Station monitoring, and modification to sites globally via the Internet. Refer to the Quick
Installation Guide (p/n 800-21668) for information regarding programming and registration. Additionally, an
internal Z-Wave module allows the Lyric Gateway to support Home Automation functions. (refer to the Gateway
Guide (p/n 800-16078 for additional information.) The controllers are compatible with the following AlarmNet
Communication Modules:
Model
Description
LYRIC-3G
GSM Cellular Communications Module
LYRIC-CDMA
CDMA Cellular Communications Module
Communications Module 24-Hour Standby Power
If 24-hour standby is required, the Super High Capacity battery (p/n 300-03866-AIO) must be installed.
RF Exposure
WARNING: The Lyric Gateway must be installed to provide a separation distance of at least 7.8
in (20 cm) from all persons and not co-located or operated in conjunction with any other
transmitter except in accordance with FCC multi-transmitter product procedures.
Install and Configure Communication Module
Follow the steps and refer to the figure below to install the Communications Module.
Installing the Cellular Communications Module
1. At the the Master User Tools Menu Programming screen select “Advanced”.
2. Select “Install Cellular Module” and follow the prompts displayed on the smart device or follow the steps
below.
3. Remove Gateway upper cover (bezel).
4. Remove the screw securing the module to the Gateway (if installed).
5. Remove the existing Cellular Communications Module (if installed).
6. Install the Cellular Communications Module into the Gateway.
7. Ensure that the Communications Module is properly seated into the Gateway and secure the module with
the provided screw (if required).
8. Insert the cover (bezel) into the Gateway
9. Slide the side cover (bezel) down to lock it in place and secure the Communications Module.
10. Select OK to complete the installation.
NOTE:The Communication Path will be dynamically adjusted when a Cellular Communication Module is
installed or removed.
11. Enable the Communications Module, configure alarm reporting and module supervision and register the
device. Refer to the “Program Communicator” and “Communications Diagnostics” sections in the
Programming Guide (p/n 800-18077). OR Log on to the AlarmNet 360TM website (http://alarmnet360.com).
The Communications Module must be registered with AlarmNet 360TM before downloading or
alarm reporting can take place.

Lyric Gateway Installation and Reference Guide
- 12 -
Installing the Gateway (Continued)
Communication Modules
Checking Signal Strength
When choosing a suitable mounting location, check the communications module’s signal strength to
ensure proper operation. For most installations, using the module’s internal antenna, mounting the
Lyric Gateway as high as practical, and avoiding large metal components provides adequate signal
strength for proper operation. To check signal strength, perform the following test.
Check Signal Strength
1. With the System in the Installer Programming mode,
select the “Comm. Diagnostics” button and then select
the “Cellular Information” button. The Cellular
Information will be displayed. The signal strength is
displayed (in dBm) as RSCP if the Lyric-3G module is
operating on the 3G Network or RSSI if the module
Lyric-3G module is operating on the 2G Network and for
the Lyric-CDMA module.
2. Compare the displayed RSCP or RSSI number to the
correct Signal Strength Guide at right to ensure
adequate signal strength. If necessary, relocate the
Controller to obtain better signal strength (select
“Cellular Information” again to refresh the reading).
3. If adequate signal strength cannot be achieved, External
Antenna Kit model Cell-ANTST should be used.
Lyric -3G Signal Strength
RSCP (3G)
Good.......................................... -20 to -90 dBm
OK................................................-91 to -100 dBm
Marginal ................................... -101 to -106 dBm
Bad ........................................... -107 to -120 dBm
RSSI (2G)
Good........................................... -20 to -89 dBm
OK................................................ -90 to -98 dBm
Marginal .................................. -99 to -104 dBm
Bad .......................................... -105 to -120 dBm
Lyric -CDMA Signal Strength
RSSI
Good........................................... -20 to -90 dBm
OK................................................-91 to -100 dBm
Marginal ................................... -101 to -106 dBm
Bad .......................................... -107 to -120 dBm

Lyric Controller Installation and Reference Guide
- 13 -
Wireless Zones
General Information
Zones
The Lyric Gateway supports up to 64 total wireless zones using 5800 and SiX™ Series transmitters, and wireless
keys.
Range
The built-in RF receiver can detect signals from wireless transmitters within a nominal range of 200 feet.
Transmitters
5800 and SiX™ Series transmitters have built-in serial numbers that must be entered into the system via
AlarmNet 360TM.Each transmitter's zone number is also programmed into the system in the “Zones”
programming section. Some transmitters, such as the 5816 can support more than one "zone" (referred to as
loops or inputs). On the 5816, for example, the wire connection terminal block is loop 1; the reed contact is loop
2. Each loop must be assigned a different zone number.
For 5800 Series wireless keys such as the 5804E, 5834-4 and 5878, you must assign a unique zone number to
each individual button used on the transmitter. Each button on the transmitter also has a pre-designated loop
or input number, which is automatically displayed.
ETL
The 5816 Transmitters do not have EOL supervision of their loop wiring, which must not exceed 3
feet.
The 5800PIR-OD, 5800SS1, 5804E, 5814, 5821, 5877 and 5878 wireless transmitters have not been
evaluated by ETL.
House Identification
If a RF House ID (RF House Code) is required to establish proper communication, the same two-digit code (01–
31) must be programmed in the Lyric, and the device. Refer to the “System Type” programming section in the
Lyric Gateway Programming Guide (p/n 800-18077). An RF House ID is not necessary for 5800 Series
transmitters and the entry should be left at “0” (default) in those cases.
Transmitter Supervision
With the exception of some transmitters/keypads that may be carried off-premises (5804E, 5834-4 and
SiXFOB), each transmitter is supervised by a check-in signal that is sent to the receiver at 70–90 minute
intervals. If at least one check-in is not received from each supervised transmitter within a 12-hour period, the
"missing" transmitter zone number(s) and "Supervision" will be displayed. The supervision for a particular
transmitter in the system that may also be carried off the premises may be turned off by entering it as an
“Unsupervised” type. For additional information, refer to the “Zones” programming section in the Lyric
Gateway Quick Installation Guide (p/n 800-21668). 5800 and SiX™ Series transmitters have built-in tamper
protection and will annunciate as a fault condition if covers are removed. In Canada the RF supervision period
is 3-hours for Fire zones and 12 hours for all other zone types.
Transmitter Input Types
Each transmitter has one or more unique factory-assigned input (loop/5800 Series or service/SiX™ Series) ID
codes. Each of the inputs requires a programming zone (e.g., a 5804E's four inputs require four button zones).
Transmitters can be entered as one of the following types (see transmitter’s instructions for appropriate
Supervision type):
Type
Description
Supervised
Sends periodic check-in signals, as well as fault, restore, and low battery signals. The
transmitter must remain within the receiver's range.
Unsupervised
Sends all the signals that the Supervised type does, but the controller does not supervise the
check-in signals. The transmitter may therefore be carried off-premises.
Button
Sends only fault signals. Do not send low battery signals until being activated. The
transmitter is unsupervised and may be carried off-premises.
Transmitter Battery Life
•Batteries in the wireless transmitters may last from 4–7 years, depending on the environment, usage, and
the specific wireless device being used. Factors such as humidity, high or low temperatures, as well as large
swings in temperature may all reduce the actual battery life in a given installation. The wireless system can
identify a true low battery situation, thus allowing the dealer or user of the system time to arrange a change
of battery and maintain protection for that point within the system.
•Button-type transmitters should be periodically tested for battery life. The 5804E, 5834-4, 5878 and SiXFOB
button transmitters have replaceable batteries.

Lyric Gateway Installation and Reference Guide
- 14 -
Wireless Zones (Continued)
RF Transmitter Loop Numbers
(Refer to this information when programming 5800 Series transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop designations.
Notes: (1) The 5806W3 smoke detector must be used in SIA applications.
(2) Button type devices send only fault and low battery signals; no restore or check-in signals.
Supervised RF devices send periodic check-in signals, faults, restore and low battery signals.
(3) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in
Go/No-Go Test Mode. Refer to the transmitter’s Installation Instructions for complete details. The
system will confirm the enrollment of the encrypted device by beeping two times.
(4) The 5800PIR-OD, 5800SS1, 5804E, 5814, 5821, 5877, and 5878 wireless transmitters have not been
evaluated by ETL.

Lyric Controller Installation and Reference Guide
- 15 -
Mechanics of Programming
Navigating
Gateway Keypad
Gateway’s keypad can be used for Basic Security Functions. The keypad provides a number of functions and
indicators. The System Status Shield is lit Green when the system is ready or flashes Red when it is not. When
the system is armed the System Status Shield is lit Red. Refer to the table below for additional indications and
functions. Additional functions are available via the My Home or Total Connect App or the associated websites.
LYRICTM Gateway
Key
Description
System Status Shield – System status is
displayed when the shield is lit as follows:
Green (steady) – Ready to Arm
Red (steady) – System is Armed
Red (slow flash) – Entry/Exit delay countdown
Red (rapid flash) – System is in Alarm
White (steady) – Waiting for User Code entry
ARMED
Away
Arm gateway in Away mode (LED steady red
when selected)
ARMED
Home
Arm gateway in Home mode (LED steady red
when selected)
Disarmed Disarm Gateway (LED flashes green until code
is entered, then turns steady green)
Alert Flashes red when an alert condition exists.
Select to hear condition
Cancel
Cancel User Code entry or Emergency
(Flashes white during an emergency)
Emergency Activates Emergency keys
Fire key -
Initiates panic fire alarm within 5
seconds of activation.
Police key -
Initiates panic police alarm within
5 seconds of activation
Medical key -
Initiates panic medical alarm
within 5 seconds of activation
Gateway Menu Mode
Entering the Master User Code or Installer Code on the Gateway keypad will provide access to Menu Mode.
Enter Menu Mode: Enter Master User or Installer Code + 1 1. The system will announce the menu options based
on the code that was entered.
Code Entered
Menu Option (System Annoucement)
Master User (1234)
Press 20 to delete all enrolled MyHome apps
Press 21 to enter MyMome app Enroll Mode
Press 31 to enter Access Aoint mode
Installer (4112)
Press 31 to enter Access Point mode
Press 51 to enter Go/No-Go Test mode

Lyric Gateway Installation and Reference Guide
- 16 -
Mechanics of Programming (Continued)
Touch-screen Display
The MyHome Gateway App is used to display screens on the smart device touch-screen. Variable
icons and text are displayed on “screens”. The screen displays status icons and associated text, the
current time and date, system status information and menu choices. The Menu area includes a list of
commands, or choices that apply to the current selection. The status area provides information
about various system events and colored text also provides an indication of system status. A “Home
Screen” is displayed whenever the App is opened.
Navigation Keys
Navigating through the screens is accomplished by lightly touching the icons or menu items on the smart device
touch-screen. Once activated, the Gateway advances to the next screen. Selecting the “” key or the “Home”
(cancel) key will return you to the previous screen or the home screen (as applicable) at any time. By touching
(selecting) an icon or key the system, depending on the function, advances to another screen, toggles between
options or scrolls through multiple options that can be selected. The system provides a prompt when a specific
input is required.
Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow
you to clearly hear the feedback announcements or system beeps from the system’s built-in speaker. To
adjust the volume, select “Settings” icon on the Home screen. Adjust the volume using the slide displayed
on the Settings screen and then select “Save” to accept.
Home Screen
System Status is displayed at the top of screen. In addition to the system status, the Home Screen displays the
current date and time and Security, Automation, TC Video, Smart Scenes and Settings icons. When Total
Connect Services are connected and web content is enabled the current weather forecast and a 5-Day Forecast
button.
Gateway Home Screen with Total Connect Services
Icon
Function
Security
Provides access to Security Screen
Automation
Provides access to Automation Screen
TC Video
Provides access to Video Screen
Smart Scenes
Provides access to Smart Scenes Programming Screen
Settings
Provides access to System Settings Screen
5-Day Forecast
Provides access to local 5-Day Weather Forecast Screen
Weather
Provides local forecast and severe weather alerts

Lyric Controller Installation and Reference Guide
- 17 -
Mechanics of Programming (Continued)
Navigating Menus
Security Screen
System Status is displayed at the top of each screen and
the time and date are displayed at the top left side of
the Security Screen. The Security Screen displays the
system status and selection “icons”. The displayed pages
and options
may vary slightly depending upon the
devices and services that are installed in or connected
to the system.
Security Screen
Selection
Function
Arm Away
Used to Arm the system in Away mode.
Arm Home
Used to Arm the system in Home mode.
Arm Custom
Used to Arm the system in Custom mode.
System Provides information about system status.
Tools
Provides access to Installer and User Programming Menus (Master User Code required for
access).
Message
Provides access to Message Center.
Zones
Provides access to Zone information and options.
Master User Menu Screen
The Master User Menu screen
provides access to the
User configurable features
. Entering the Master User
Code is required to access the User Tools Menu.
Master User Menu Screen

Lyric Gateway Installation and Reference Guide
- 18 -
Mechanics of Programming (Continued)
Programming
If the system is Armed or in Alarm, the Tools icon will not be functional. The system must first
be disarmed.
Master User Features
SCREEN
ACTION
Master User Menu Screen
1. Select the “Security” icon.
2. Select “Tools” icon.
3. Enter the Master User Code 1234 on the displayed
keypad.
4. Select one of the following options:
System Information
Install Cellular Module
Install Backup Battery
Update Sensor Firmware
Walk Test
Comm. Test
Reboot
Update Keypad Firmware
5. The system advances to the screen for the selected
option.
Exit Programming Mode
1. Select the “” key to exit the current screen OR select the Home key to return to the Home Screen.

Lyric Controller Installation and Reference Guide
- 19 -
Zone Response Type Definitions
General Information
During programming, you must assign a zone type to each zone, which defines the way in which the system
responds to faults in that zone. Zone types are defined below.
Type
Function
Characteristics
Not Used
Used to program a zone that is not used.
•None
Entry/Exit 1
(Burglary)
Usually assigned to sensors or contacts on
primary entry and exit doors.
•Entry delay #1 is programmable.
•Exit delay is independently programmable.
•Exit and entry delays when armed in Away, Stay or Night
Stay mode.
•No entry delay when armed in Stay or Away Instant modes.
•Exit delay regardless of the arming mode selected.
Entry/Exit 2
(Burglary)
Usually assigned to sensors or contacts on
secondary entry and exit doors that might
be further from the keypad (typically used
for a garage, loading dock, or basement
door).
•
Entry delay #2 is programmable.
•Exit delay is independently programmable.
•Secondary entry delay, if armed in the Away or Stay mode.
•No entry delay when armed in the Stay Instant or Away
Instant mode.
• Exit delay begins regardless of the arming mode selected.
Perimeter
(Burglary)
Usually assigned to all sensors or contacts
on exterior doors and windows
•Instant alarm, when armed in Away, Stay, Stay No Delay,
Night Stay or Away Instant mode.
Interior, Follower
Usually assigned to a zone covering an area
(i.e.: foyer, lobby, or hallway) that must be
passed upon entry (after faulting the
entry/exit zone) to reach the keypad.
Provides an instant alarm if the entry/exit
zone is not violated first, and protects an
area in the event an intruder has hidden on
the premises before the system is armed, or
gains access through an unprotected area.
• Delayed alarm (using the programmed entry/exit time) if
entry/exit or interior-with-delay zone is faulted first.
•Instant alarm in all other situations.
•Active when armed in Away or Away Instant mode.
•Bypassed automatically when armed in Stay, Night Stay or
Stay Instant mode.
Trouble by Day/
Alarm by Night
Usually assigned to a zone that covers a
sensitive area (i.e.: stock room, drug supply
room, etc.) It can also be used on a sensor or
contact in an area where immediate
notification of an entry is desired.
•Instant alarm, when armed in Away, Stay, Night Stay , Stay
Instant, or Away Instant (night) mode.
•Provides a latched trouble sounding from the keypad and, if
desired, a Central Station report when disarmed (day).
24-hour Silent
Alarm
Usually assigned to a zone containing an
Emergency button (silent emergency).
• Sends a report to the Central Station but provides no keypad
display or sounding.
•In disarmed state sends a report to the Central Station
displays "Not Ready to Arm" on the keypad and “Away”,
“Stay” and “Tools” buttons are disabled.
24-hour Audible
Alarm
Usually assigned to a zone containing an
Emergency button (audible emergency).
•Follows sounder timeout
•Sends a report to the Central Station, and provides alarm
sounds at the keypad.
24-hour
Auxiliary
Alarm
Usually assigned to a zone containing a
button for use in personal emergencies or
to a zone containing monitoring devices
(i.e.: water or temperature sensors, etc.).
•Sends a report to the Central Station and provides an alarm
sound at the keypad. (There is no keypad timeout.)
Silent Burglary
Usually assigned to sensors or contacts on
exterior doors and windows where sirens are
NOT desired.
•Instant alarm, with No audible indication when armed in the
Away, Stay, Stay No Delay, Night Stay, or Away Instant mode.
•Report sent to the Central Station.
Local Alarm Usually assigned to a zone containing an
Emergency button (audible emergency).
•Follows sounder timeout.
•Provides alarm sounds at the keypad.
•No reports to the Central Station.
Interior with Delay
Provides entry delay (using the programmed
entry time), if tripped when the controller is
armed in the Away mode. Bypassed when the
controller is armed in the Stay or Stay Instant
mode.
•Entry delay #1 (with programmed entry time) when armed in
the Away mode.
•Entry delay begins whenever sensors in this zone are
violated, regardless of whether an entry/exit delay zone was
tripped first.
•No entry delay when armed in the Away Instant mode.
• Exit delay regardless of the arming mode selected.
24-hour Carbon
Monoxide Monitor
Can be assigned to any wireless zone with a
carbon monoxide detector. This zone type is
always active and cannot be bypassed.
•Local keypad and detector will sound when this zone type is
alarmed. (Pulse Temporal 4).
Trouble
Used with Other response type.
•The system will provide a trouble sounding from the keypad
(and a Central Station report, if desired).
Fire No
Verification
Can be assigned to any wireless zone used
as a fire zone. This zone type is always
active and cannot be bypassed.
•Alarm sound will pulse (Temporal Fire) when this zone type is
alarmed.

Lyric Gateway Installation and Reference Guide
- 20 -
Zone Response Type Definitions (Continued)
Type
Function
Characteristics
Fire with
Verification
Can be assigned to any wireless zone used
as a fire zone. Fire with verification is
available with smoke detector device type. It
cannot be used with heat detectors,
combination heat/smoke detectors or fire
pull stations. This zone type is always active
and cannot be bypassed.
•
Alarm sound will pulse (Temporal Fire) when this zone type is
alarmed and the alarm has been verified.
•System verifies alarm by delaying reporting and alarm
sounding for 30 seconds after alarm is detected. If the zone
remains faulted after 30 seconds a fire alarm is provided. If
any other fire zone is faulted during the 30 second delay
window a fire alarm is immediately provided for that zone.
An alarm for original fire zone will also be provided, if that
zone is still faulted. If there are no fire alarms after the 30
second delay expires, the system will open a 60 second
window. If any fire zone is faulted during that window a fire
alarm will immediately be provided for that zone.
Arm–Stay
Special-purpose zone type used with 5800
and SiX™ Series wireless keys.
•Exit delay regardless of the arming mode selected.
•System is armed in the Stay mode when the zone is
activated.
Arm–Away
Special-purpose zone type used with 5800
and SiX™ Series wireless keys.
•System is armed in the Away mode when the zone is
activated.
Disarm
Special-purpose zone type used with 5800
and SiX™ Series wireless keys.
•Disarms the system when the zone is activated.
No Alarm
Response
Assigned when no-alarm response is required.
•No reports to the Central Station.
•No keypad sounding or chime and no display on screen.
• System can still be armed.
Monitor
Can be assigned to any wireless zone used
for asset protection. Works as a dynamic
monitor of a zone fault/trouble (not alarm).
•Reports to the Central Station, if enabled.
•Fault/restore events are logged by the system.
•Activity Zone No. and Zone Descriptor displayed on LCD.
•Restore will be stored in event log.
•No keypad sounding or chime.
• System can still be armed.
General Monitor
Assigned sensors or contacts on doors and
windows or asset protection within the
premises. Used to track activity of the
occupant and alert occupant of the activity
of others.
•No reports to the Central Station.
•Fault/restore events are logged by the system.
•Monitors entry into a monitored area. Activates a one-time
announcement when faulted.
•
Activity Zone No. and Zone Descriptor displayed on LCD.
General
Response
Assigned sensors or contacts on doors and
windows or asset protection within the
premises. Used to track activity of the
occupant and alert occupant of the activity
of others.
•No reports to the Central Station.
•Fault/restore events are logged by the system.
•Monitors entry into a monitored area. Activates a zone
announcement when faulted.
•Activity Zone No. and Zone Descriptor displayed on LCD.
•System re-triggers audible sounding every ten seconds until
acknowledged.
Resident Monitor
Used to monitor a resident in an area
deemed to be dangerous by a caregiver.
•No reports to the Central Station.
•Monitors entry into a monitored area. Activates a zone
announcement when faulted.
•Activity Zone No. and Zone Descriptor displayed on LCD.
• Fault/Restore events are not logged by the system.
Resident
Response
Used to monitor a resident in an area
deemed to be dangerous by a caregiver.
Requires acknowledgement by caregiver.
•
No reports to the Central Station.
•Monitors entry into a monitored area. Activates a zone
announcement when faulted.
•Activity Zone No. and Zone Descriptor displayed on LCD.
•System re-triggers audible sounding every ten seconds until
acknowledged (Off sequence or wireless key).
• Fault/Restore events are not logged by the system.
Garage
(Burglary)
Assigned to Automatic Garage Door
applications. Provides a status of the garage
door close/open real time state.
•Associated With Entry Delay #2 Programmed Time.
•Exit delays when armed in Away, Stay or Night Stay mode.
•No Entry Delay when armed in Away or Stay Instant modes.
•System can be armed with zone in the faulted state. When the
zone is closed it will automatically be inclusive within
protection points. If the point is subsequently violated, it will
initiate an alarm.
Garage Monitor
Assigned to Automatic Garage Door
applications. Provides a status of the garage
door close/open real time state.
•Can be assigned to any wireless zone used for automatic
“Garage Door” Open/Close status.
•Will not initiate an alarm condition on the controller.
•When zone is in the open state will display “FAULT.”
•Does not report alarms to Central Station.
•Zone will chime if enabled.
• System can be armed if this zone type is in fault.