Honeywell Dolphin 70e Black User manual

Dolphin™ 70e Black
with Windows®Embedded Handheld 6.5
Quick Start Guide
70E-WEH-QS Rev B
6/13

Out of the Box
Verify that your carton contains the following items:
• Dolphin 70e Black mobile computer (terminal)
• Rechargeable 3.7V Li-ion Battery
• USB charge/communication cable
• Power adapter with regional plug adapters
• Quick Start Guide
• Compliance Regulatory Sheet
If you ordered accessories for your terminal, verify that they are also included
with the order. Be sure to keep the original packaging in case you need to
return the Dolphin terminal for service.
Note: Your Dolphin model may differ from the model illustrated in this guide;
however, the features noted are standard for all Dolphin 70e Black models
with Windows Embedded Handheld unless otherwise indicated.

Getting to Know the Dolphin 70e Black
Front
Microphone*
Scan Button
General Notification LED
Right Scan/
Image Button
USB Door/
Micro USB
Port
End Button
Home Button
Side
Microphone*
Send Button
Back Button
WAN Notification
LED
Front Speaker
Touch Panel
Display
Bottom Speaker
*Important - Do not cover the side microphone with your
hand when using the terminal for phone calls or audio
recordings. Both the front and side microphones must
be free from obstruction for the noise cancellation
feature to function.

Camera
Flash/
Flashlight
Color
Camera
Lens
I/O Connector
Battery Door
(standard model shown)
Volume Control Button
Left Scan/Image Button
Power Button
Audio Jack
Image Engine Window (LED aperture)
Battery Latch and Retention Strap
(battery and battery door not shown)
SIM Card Socket
Memory Card Socket
Memory Card Retention Flap
SIM Card
Retention Flap
SIM Card Socket

Installing the Battery
Dolphin 70e Black model terminals are designed for use with battery part
numbers BAT-STANDARD-01 (Li-ion 3.7 V, 6.179 watt hour) and
BAT-EXTENDED-01 (Li-ion 3.7 V, 12.358 watt hour) manufactured for
Honeywell International Inc.
The Dolphin 70e Black is shipped with the battery packaged separately from
the terminal. Perform the steps illustrated below to install the battery.
Ensure all components are dry prior to placing the battery in the
terminal. Mating wet components may cause damage not covered by
the warranty.
!
23
4
6
7
1
5
Note: Standard model battery
and battery door shown.
89

We recommend use of Honeywell Li-ion battery packs. Use of any non-
Honeywell battery may result in damage not covered by the warranty.
Once the battery is installed, connect the terminal to one of the Dolphin 70e
Black charging peripherals to charge the battery.
Charging the Dolphin 70e Black
Dolphin terminals ship with the battery significantly discharged of power.
Charge the battery with a Dolphin charging device for a minimum of 4 hours
for the standard battery and 6 hours for the extended battery. When using the
70e-USB Charge/Communication cable to charge from a 500mA USB port on
a host device, charge the battery for a minimum of 6 hours for the standard
battery and 8 hours for the extended battery.
Note: Using the terminal while charging the battery significantly increases the time
required to reach a full charge.
We recommend use of Honeywell peripherals, power cables, and power
adapters. Use of any non-Honeywell peripherals, cables, or power
adapters may cause damage not covered by the warranty.
Dolphin 70e Black model terminals are designed for use with the following
charging devices and cables: 70e-HB, 70e-CB, 70e-MB, 70e-MC, and the
70e-USB ADAPTERKIT.
Ensure all components are dry prior to mating terminals/batteries with
peripheral devices. Mating wet components may cause damage not
covered by the warranty.
HomeBase (Model 70e-HB)
The 70e-HB charger is designed for use with Dolphin 70e Black model
terminals, and battery part numbers BAT-STANDARD-01 (Li-ion 3.7V, 6.179
watt hour) and BAT-EXTENDED-01 (Li-ion 3.7V, 12.358 watt hour)
manufactured for Honeywell International Inc.
Use only a UL Listed power supply, which has been qualified by Honeywell
with output rated at 12VDC and 3 amps with the device.
!
!
!

HomeBase Parts
HomeBase LED Indicators
AUX battery LED
Orange The auxiliary battery is charging.
Green The auxiliary battery has completed charging and is ready
for use.
Dock LED
Blue The terminal is properly seated in the base.
COMM LED
Green A USB connection is established with the host workstation.
2
AUX Battery Well
AUX
Battery LED
COMM LED
Dock LED
AC Power Cord
USB Port
DC Power
Jack
Power Adapter
Power Cable

USB Charge/Communication Cable (70e-USB ADAPTERKIT)
The USB Charge/Communication cable provides two options for charging the
terminal. Use the cable in conjunction with the provided power supply adapter
and plug adapter to charge the terminal from a power outlet or connect the
cable to a high-power USB port to charge from a host device.
Option 1: Charging from a power outlet
Use only a UL Listed power supply, which has been qualified by Honeywell
with an output rated at 5VDC and 1A with the device.
Option 2: Charging from a high-power USB port on a host device
Note: Charging the battery through a USB port takes more time than direct AC
adapter charging. USB charging will not take place if the terminal is drawing
more current than supplied by the USB port.
Touch > Settings > System > Power to verify the battery is charging.
Power
Adapter
Micro
USB Port
USB Door
Plug Adapter
70e-USB Charge/
Communication Cable
Micro USB
Port
USB
Door
Host Device
USB Port
70e-USB Charge/
Communication Cable

Turning Power On/Off
To turn the terminal On, press and release the Power button .
To turn the terminal Off:
1. Press and hold the Power button for approximately 4 seconds until
the options menu displays.
2. Touch Power off.
Suspend Mode
Suspend mode automatically turns the touch screen off to save battery power
when the terminal is inactive for a programmed period of time. The automatic
timeout limits are adjustable from the Advance tab located under Settings >
System > Power.
Press and release the Power button to toggle the terminal in or out of
Suspend Mode.
Note: You should always place the terminal into Suspend mode before removing
the battery.
Removing the Battery
1. Place the terminal in Suspend mode.
2. Perform the steps illustrated below to remove the battery.
1
2
54
36

Installing the SIM Card and/or Memory Card
Honeywell recommends the use of Single Level Cell (SLC) industrial grade
microSD™ or microSDHC™ memory cards with Dolphin terminals for
maximum performance and durability. Contact a Honeywell sales
representative for additional information on qualified memory card options.
To install the SIM Card and/or Memory Card:
1. Place the terminal in Suspend mode.
2. Remove the battery door and battery.
3. Lift the card retention flap for the appropriate socket.
4. Slide the SIM or memory card (contacts facing down) into the socket,
then close the retention flap.
Note: Format microSD/SDHC card before initial use.
5. Install the battery and battery door. The terminal begins booting as soon
as power is applied.
Memory Card
Retention Flap
SIM Card
Retention Flap
Chamfered
Corner of
SIM Card