Honeywell 720P User manual

Document 800- 14746 Rev. A
Honeywell
720P&D1
IR Vandal Dome Camera
User’s Manual

Honeywell
i
Owner's Record
The model and serial numbers are located at the bottom of device. Record these numbers in
the spaces provided below. Refer to these numbers whenever you call upon your dealer
regarding this product.
Model No. ____________________
Serial No. ____________________
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
For AC Adaptor to avoid electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.
Notice: The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
For Customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
The shielded interface cable recommended in this manual must be used with this equipment
in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC
Rules.

Honeywell
ii
Declaration of Conformity
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority
to operate the device.
NOTICE TO USERS
© 2006~12 All rights reserved. This manual or the software described herein, in whole or in
part, may not be reproduced, translated or reduced to any machine readable form without
prior written approval.
WE PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL, THE SOFTWARE
OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
ANY PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE SOFTWARE OR
SUCH OTHER INFORMATION. IN NO EVENT SHALL WE BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS
MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE
USE THEREOF.
We reserve the right to make any modification to this manual or the information contained
herein at any time without notice. The software described herein may also be governed by
the terms of a separate user license agreement.

Honeywell
iii
Contents
1 Overview.................................................................................................................................... 1
Introduction ................................................................................................................................. 1
Features ..................................................................................................................................... 1
Minimum System Requirements.................................................................................................. 2
2 Package Contents ..................................................................................................................... 3
3 Connections .............................................................................................................................. 4
Connector Cable (Option) ........................................................................................................... 4
Connector board ......................................................................................................................... 6
4 Hardware Installation ................................................................................................................ 9
5 Install the Camera in LAN ....................................................................................................... 11
6 Preparation.............................................................................................................................. 12
Search and Set up by IP Wizard II............................................................................................. 12
Search................................................................................................................................ 12
View ................................................................................................................................... 13
LAN .................................................................................................................................... 14
Wireless ............................................................................................................................. 16
UPnP of Windows® XP, Vista or 7 ............................................................................................ 16
Install the Device behind a NAT Router ..................................................................................... 17
Access the device from the Internet Explorer for the first time.................................................... 17
Logging in as an Viewer ............................................................................................................ 19
Logging in as an Administrator .................................................................................................. 19
7 Operating the Network Camera .............................................................................................. 20
Monitor Image Section .............................................................................................................. 20
Video Profile ............................................................................................................................. 21
Streaming Protocol ................................................................................................................... 21
Language.................................................................................................................................. 21
2-Way Audio ............................................................................................................................. 21
Full Screen ............................................................................................................................... 21
PTZ Control .............................................................................................................................. 22
ActiveX Control ......................................................................................................................... 23
Digital Zoom ....................................................................................................................... 23
Snapshot ............................................................................................................................ 24
Record................................................................................................................................ 24
Volume ............................................................................................................................... 25
About.................................................................................................................................. 25

Honeywell
iv
8 Administrating the Device ...................................................................................................... 26
System Setting.......................................................................................................................... 26
Network: Configure Network settings .................................................................................. 26
Camera: Adjust Camera parameters ................................................................................... 37
System: Configure and maintain system ............................................................................. 43
Video: Configure OSD, Overlay, Profile, and ROI................................................................ 47
Audio: Audio parameters..................................................................................................... 52
User: Manage user name, password and login privilege...................................................... 52
E-Mail: Setup E-Mail configuration ...................................................................................... 55
Event Detection .................................................................................................................. 56
Storage: Status and configuration of SD card and SAMBA Server....................................... 58
Continuous Recording ........................................................................................................ 60
Recording List: Files list inside the SD card or SAMBA server ............................................. 61
Event Server: Setup FTP/TCP/HTTP/SAMBA server configuration...................................... 62
Event Schedule: Configure the event schedule ................................................................... 67
9 Appendix A: Alarm I/O Connector .......................................................................................... 72
Connector cable........................................................................................................................ 72
Connector board ....................................................................................................................... 72
10 Appendix B: Troubleshooting & Frequently Asked Questions ............................................. 75
11 Appendix C: PING IP Address ................................................................................................ 79
12 Appendix D: Bandwidth Estimation ....................................................................................... 80
13 Appendix E: Specifications .................................................................................................... 81
14 Appendix F: Configure Port Forwarding Manually ................................................................ 85
15 Appendix G: Power Line Frequency ...................................................................................... 88

Honeywell
1
1 Overview
The user’s guide explains how to operate this camera from a computer. User should read
this manual completely and carefully before you operate the device.
Introduction
This camera is an inexpensive and fully scalable surveillance device. Because the Network
Cameras can be plugged into your existing local area network (LAN), you will potentially
save thousands of dollars from unnecessary cabling.
The device is accessible via the LAN or Internet connection. Connect your device directly to
a local area network or xDSL modem, and with web browser you get instant, on demand
video streams. Within minutes you can set up the device to capture a video sequence to a
PC. The live video can be uploaded to a website for the world to see.
Features
• Sony Exmor™ image sensor
• 720P : 720p / 1.3 Mega mode ; SVGA/D1 : 800x600 / D1 mode
• 720P : 60fps in all resolutions ; SVGA/D1: 30fps in all resolution
• ONVIF compliant
• Camera tampering and audio detection
• Gigabit 1000Base-T Ethernet
• Vandal proof and IP66 enclosure
• 12pcs High-light IR LED, 10~15m IR distance
• Day and night function with ICR
• Easy installation with setup wizard (IP Wizard II)

Overview
2
• UPnP device discovery and NAT router transversal for easy installation
• Dynamic IP Service, DIPS®, to search your IP camera from Internet easily
• H.264, MPEG4 and MJPEG triple compression simultaneously
• 12-profile encoder simultaneously
• UDP / TCP / HTTP / HTTPS protocols selectable
• Event and Continuous recording to SD card or SAMBA server
• External microphone input
• Audio line out
• Two-way audio
• Composited video out
• Micro SD slot
• Intelligent motion detection up to 10 zones
• Voice alerting while event triggered
• Privacy masks
• 3D noise reduction to improve picture quality at low lux.
• Digital WDR to provide clear images even under back light circumstances
• Image transmission using an FTP or e-mail for event
• Digital sensor input and alarm output
• Multi-channel control software for surveillance application
• IEEE 802.3af PoE support
Minimum System Requirements
• Microsoft Internet Explorer 8.0 or later
• Microsoft Media Player 11.0 or later (to playback recorded file)
• VGA Monitor resolution 1280 x 1024 or higher
• Intel Core 2 Duo E8600(3.33GHz) or faster
• Memory Size: 2GB or more
• Windows XP, Vista, 7

Honeywell
3
2 Package Contents
User can find the following items in the package:
Item Descriptions
1. This camera is the main element of the product.
2. Accessories
3. User’s Manual CD provides important information and
instructions for operating the Network Camera...
If any of the above items are missing, please contact your dealer immediately.
Note: Using a power supply with a different voltage than the one included with the Network
Camera will cause damage and void the warranty for this product.

Connections
4
3 Connections
There are two types. One is cabling with built-in connector board and the other one is with
connector cable.
Note that user must choose only one of these two configurations. The camera does not
support both cabling at the same time.
Connector Cable (Option)
1. RJ45 LAN socket: Connect to PC or Hub/Switch.
It’s for connections to 10Base-T Ethernet, 100Base-TX, or 1000Base-TX Ethernet cabling.
This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the
network automatically. Please use Category 5 or better cable to connect the Network
Camera to an Ethernet network switch or hub.

Honeywell
5
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
Power LED (orange color)
This LED is used to indicate whether DC power is on or not.
2. RS-485: Connect to a local keyboard controller.
DI/ DO: Connect to sensor in and alarm out devices
Cable for I/O connectors:
Name Number Function
12VDC 1 DC 12V (50mA maximum)
DI 2 Digital signal input
GND 3 GND
DO 4 Digital signal output
485+ 5 RS485 data +
485- 6 RS485 data -
3. Factory Default Reset
This button is used to restore the all factory default settings. Sometimes restarting the device
will make the system back to a normal state. However, if the system still got problems after
restart, user can restore the factory default settings and install it again.
Restore the device:
a) While the Camera is ready and then press the button down continuously.
b) Hold the button at least 5 seconds and release it. Then the device has been
restored to default settings and reboot again.
Note: Restoring the factory default setting will lose the all previous settings included IP
address forever. User needs to run the IP Wizard II program to search the device and
configure it to let the device work properly again.
4. DC-in Jack
The input power is 12VDC. Note that supply the power to the Network Camera with the
power adapter included in package.
5. MIC in (audio in)
Connect a microphone to the network camera.
6. Line out (audio out)
Connect a loud speaker to the network camera. This function is for voice alerting and
two-way audio.
7. Video out (BNC connector)

Connections
6
The Network Camera also provides composite video output. The video output function is
only for easy installation to check view angle and focus. The output is not a Mega-pixel
resolution. Furthermore, the video output is off by default. To turn on video, please refer to
Setting\Camera\Picture chapter.
Connector board
Note that to cabling this camera by type of connector board, firstly, user must remove the
attached “connector cable” from wafer 1~ 6 shown as below:
1. RJ45 LAN socket:
The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet, 100Base-TX, or
1000Base-TX Ethernet cabling. This Ethernet port built N-Way protocol can detect or
negotiate the transmission speed of the network automatically. Please use Category 5 or
better cable to connect the Network Camera to an Ethernet network switch or hub.
In the LAN socket, there are two LEDs embedded:

Honeywell
7
LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
Power (orange color)
This LED is used to indicate whether DC power is on or not. In addition, this LED will be
flashing while the wireless accessing of the Camera.
2. Terminal block
Pin definition:
Pin Name Function
1 12VDC in DC 12V power input
2 MIC in- External MIC input-
3 MIC in+ External MIC input+
4 Audio out+
5 Audio out-
6 Video out Composited video output
7 12VDC out DC 12V output (50mA maximum)
8 DI Digital signal input
9 GND Digital ground
10 DO Digital signal output
11 RS485+ RS485 data +
12 RS485- RS485 data -
12VDC in
The input power is 12VDC. Note that supply the power to the Network Camera with the
power adapter included in package.
MIC in +/- (audio in)
Connect an external microphone to the camera.
Audio out +/-
Connect a loud speaker to the camera. This function is for voice alerting and two-way audio.
Video out
Connect a TV monitor to the camera. User can check the focus/zoom and view angle of the
camera.
12VDC out

Connections
8
The output power is 12VDC. This is used to support DI/DO devices. The output power is
12VDC/50mA maximum.
DI/GND/DO/RS485
Interface of Digital input/output and RS485
a) AC24V Block
b) Factory Default Reset
This button is used to restore the all factory default settings. Sometimes restarting the device
will make the system back to a normal state. However, if the system still got problems after
restart, user can restore the factory default settings and configure it again.
3. Restore the device
i) Press the button down continuously.
ii) Hold the button at least 5 seconds and release it. Then the device has been
restored to default settings and reboot again.
Note: Restoring the factory default setting will lose the all previous settings included IP
address forever. User needs to run the IP Wizard II program to search the device and
configure it to let the device work properly again.
4. Micro SD Card Slot
User can insert a micro SD card into this slot for recording.
In case, you want to use the attached cable to connect this camera again, please check and
plug the cable to wafer 1~6 properly and carefully.

Honeywell
9
4 Hardware Installation
1. Use the provided L-wrench, loosen the tamper-resistant housing cover (with
screws still attached on the cover). The unit has a factory installed side conduit
entry and one may adjust the cables to back conduit entry according to
installation requirement.
2. Set the mounting base onto the wall or ceiling and center it over the mounting
hole, using the supplied two retaining screws to secure the main body.
3. Set the proper image by moving the camera body (some model may be limited by
the PCB board to180°rotational adjustment) and set the focus by turning the lens
to the left or right direction.
4. Connect video output cable (BNC) to a TV monitor. Once the picture appears on
the monitor, adjust the lens wrench to “TELE←→WIDE” of the lens, get the view
zoom that you desire, and then adjust the focus wrench to “NEAR←→FAR” of
the lens to obtain the best clear picture. After adjustment, tighten both wrenches.

Hardware Installation
10
5. When the camera focus adjustment has been completed, use the provided
L-wrench to fasten the tamper-resistant housing to the main body.

Honeywell
11
5 Install the Camera in LAN
1. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket and attach it into the network.
2. Connect the external power supply to Camera, if not powering by PoE
Connect the attached power adapter to the DC power jack of the camera.
Note: Use the power adapter, 12VDC, included in the package and connect it to wall outlet
for AC power.
Once you have installed the camera well and powered it on, the Power LED (orange) will
turn on later. The Power LED turned on, it means the system is booting up successfully.
Furthermore, if you have a proper network connection, and access to the camera, the LAN
LED (green) will flash.

Preparation
12
6 Preparation
Search and Set up by IP Wizard II
Once you installed the Camera on a LAN environment, you have two easy ways to search
your Cameras by IP Wizard II or UPnP™ discovery. Here is the way to execute IP Wizard II
to discover Camera’s IP address and set up related parameter in a Camera.
Search
When launch the IP Wizard II, a searching window will pop up. IP Wizard II is starting to
search Network Cameras on the LAN. The existed devices will be listed as below.

Honeywell
13
View
If IP Wizard II finds network devices, View button will be available. Please select the device
you want to view and click the View button. Then you could see the video from camera
directly. Furthermore you could double click the left button of mouse to link to the network
device by web browser.

Preparation
14
LAN
In case you want to change the IP related parameters of wired interface, please select the
device you want to configure and click the LAN button. Relative settings will be carried out
as below.
You could modify the relative settings of the selected device. Click “<<” button will quit the
LAN setting procedure and click “>>” button will move to next page as below.