Honeywell Silent Knight 6860 Technical manual

6860
Remote Annunciator
Product Installation Document
Document LS10174-001SK-E:B 2/15/2022 ECN: 151062
1 Description
The 6860 is an optional 4x40 remote annunciator that can be surface or
flush-mounted.
1.1 Compatibility
The 6860 is compatible with the Silent Knight Series FACPs. For more
information, refer to the FACP Manual.
1.2 Specifications
2 Installation
1. Ensure power is turned off at the panel.
2. Mount the 6860 in the desired location. See Section 2.1.
3. Connect the 6860 to the panel. See Figure 5.
4. Use the DIP switches on the back of the 6860 to assign an ID
number. Refer to the FACP manual.
5. The 6860 module must be added to the system through FACP
programming. JumpStart can be used to automatically add the
module or it may be added manually. Refer to the FACP Manual for
more information.
2.1 Mounting
2.1.1 Flush Mounting
Follow these steps to flush mount the 6860.
1. The backbox dimensions are 9.25” W x 8.375” H. The minimum
depth required is 2". Mount the backbox using the mounting holes
shown below.
2. Remove knockouts as needed for wires. There are 10 knockouts
available, two on each side and two in the back of the cabinet.
3. Wire the annunciator board to the main control panel as shown in
Figure 5.
Operating Voltage: 24VDC
Current Standby Current: 27mA
Alarm Current: 53mA
Operating Temperature: 32° to 120° F (0° to 49° C)
Dimensions Flush Mount: Overall:
12.25” W x 11.5” H x 0.875” D
(31.1 cm W x 29.2 cm H x 2.2 cm D)
Backbox: 9.25” W x 8.375”H
(23.5cm W x 21.27cm H)
Surface Mount: Including trim ring:
12.25” W x 11.5” H x 3.0” D
(31.1 cm W x 29.2 cm H x 7.6 cm D)
Table 1 Specifications
Model 6860
BACK BACK BACK
NEXT NEX T NEXT
Figure 1 6860 Remote Annunciator
mounting holes
mounting holes
Figure 2 6860 Backbox Mounting

Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472-1610
203.484.7161
www.silentknight.com
LS10174-001SK-E | B | 02-22
©2022 Honeywell International Inc.
4. Attach the annunciator and door assembly to back box as shown
below using the supplied screws.
2.1.2 Surface Mounting
The RA-100TR Red Trim Ring kit is available for use when surface
mounting the 6860.
1. Remove the desired knockout.
2. Mark and pre-drill hole in the wall for the center top keyhole
mounting bolt. Refer to Figure 2 for mounting hole locations.
3. Install center top fastener in the wall with the screw head
protruding.
4. Place backbox over the top screw, level and secure.
5. Mark and drill the left and right upper and lower mounting holes.
6. Install remaining fasteners and tighten.
7. Run wires to the control panel. Refer to Figure 5.
8. Place the trim ring over the back box as shown below.
9. Attach the door assembly to the backbox using the screws provided.
Refer to Figure 3.
3 Wiring Connections
Wire the 6860 to the FACP as shown in below.
Figure 3 Attaching Annunciator/Door Assembly
Figure 4 Installing Trim Ring
SBUS OUT
–+AB
S– S+ AB
ON
12345
6
DIP Switches
remote annunciator
(back view)
supervised,
power-limited,
Class B
Figure 5 SBUS Connections