Honeywell Granit XP 1990i User manual

Granit™ XP 1990i
Industrial Area-Imaging Scanner
Quick Start Guide
1990-EN-QS-01 Rev A
5/20

1
Agency Model: 1990i, 1990iSR, 1990iXR
Note: Refer to your User Guide for information about cleaning
your device.
Get Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

2
Connect the Scanner
When connecting the scanner, make sure the cable is pushed
tightly into the scanner. Loosen the locking plate and slide it
over the base of the cable connector to lock the cable in place.
Tighten the screw.
USB:
IP65/67
2
3
1

3
Keyboard Wedge:
RS232 Serial Port:

4
Reading Techniques
The view finder projects an aiming beam that should be cen-
tered over the barcode, but it can be positioned in any direction
for a good read.
Standard Product Defaults
The following barcode resets all standard product default set-
tings.
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Hon-
eywell website (www.honeywellaidc.com). The driver will use the
next available COM Port number. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
SR Models: XR Models:
Standard Product Defaults
USB Serial

5
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Keyboard Country
Scan the appropriate country code below to program the key-
board layout for your country or language. By default, national
character replacements are used for the following characters:
#$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart
in your User Guide to view the character replacements for each
country.
USB PC Keyboard
USA (Default)
Belgium
Denmark
Finland
France

6
Note: For a complete list of country codes, see the User Guide for
your product.
Germany/Austria
Great Britain
Italy
Norway
Spain
Switzerland

7
Trigger
The following barcodes will allow you to use the scanner in
Manual Trigger - Normal Mode (need to press the trigger to
read) or Presentation mode (the scanner is activated when it
“sees” a barcode).
Streaming Presentation™
When in Streaming Presentation mode, the scanner leaves the
scan illumination on all the time and continuously searches for
barcodes.
Suffix
If you want a carriage return after the barcode, scan the Add CR
Suffix barcode. To add a tab after the barcode, scan the Add Tab
Suffix barcode. Otherwise, scan the Remove Suffix barcode to
remove the suffixes.
Manual Trigger - Normal
(Default)
Presentation Mode
Streaming Presentation Mode
Add CR Suffix

8
Add Code ID Prefix to all Symbologies
Scan the following barcode if you wish to add a Code ID prefix to
all symbologies at once.
Note: For a complete list of Code IDs, see the User Guide for your
product.
Function Code Transmit
When this selection is enabled and function codes are con-
tained within the scanned data, the scanner transmits the func-
tion code to the terminal. Charts of these function codes are
provided in your User Guide. When the scanner is in keyboard
wedge mode, the scan code is converted to a key code before it
is transmitted.
Add Tab Suffix
Remove Suffix
Add Code ID Prefix To All Symbologies
(Temporary)
Enable
(Default)
Disable

9
Support
To search our knowledge base for a solution or to log into the
Technical Support portal and report a problem, go to
www.hsmcontactsupport.com.
User Documentation
For the user guide and other documentation, go to
www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and
click Resources > Product Warranty.
Patents
For patent information, see www.hsmpats.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not repre-
sent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omis-
sions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.