Honeywell Voyager XP 1472g Series User manual

Voyager™ XP 1472g Series
Cordless Area-Imaging Scanner
Quick Start Guide
VG1472-EN-QS-01 Rev A
6/19
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Honeywell Voyager XP 1472G o
cerca il tuo prodotto tra le migliori offerte di Palmari e Barcode Scanner

Note: Refer to your user’s guide for information about cleaning
your device.
For localized language versions of this document, go to
www.honeywellaidc.com.
Getting Started
Turn off the computer’s power before connecting the base, then
power up the computer once the base is fully connected. When
the base is connected and powered up, put the scanner in the
base to establish a link. The green LED on the base flashes to
indicate the scanner’s battery is charging.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

USB Connection:
Keyboard Wedge Connection:

RS232 Serial Port Connection:
RS485 Connection:

Reading Techniques
The view finder projects an aim-
ing dot that should be centered
over the bar code, but it can be
positioned in any direction for a
good read.
Hold the scanner over the bar
code, pull the trigger, and center
the aiming dot on the bar code.
The aiming dot is smaller when
the scanner is closer to the code
and larger when it is farther from the code. Hold the scanner
close to smaller bar codes, and farther away from large bar
codes to get a proper read.
If the bar code is highly reflective (e.g., laminated), you may need
to tilt the scanner at an angle so the bar code can be scanned.
Note: If the scanner razzes when scanning a bar code, the link
has not been established. If the scanner beeps once, the
link has been established.
Standard Product Defaults
The following bar code resets all standard product default set-
tings.
Note: PDF and 2D bar codes can only be read by Voyager model
1472g2D and cannot be read by model 1472g1D.
Standard Product

RS485 Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to pro-
gram the terminal, then power cycle the cash register.
Note: For additional RS485 interface selections, see the User’s
Guide for your product.
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Hon-
eywell website (www.honeywellaidc.com). The driver will use the
next available COM Port number. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Interface
USB Serial

USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Keyboard Country
Scan the appropriate country code that follows to program the
keyboard layout for your country or language. By default,
national character replacements are used for the following
characters: #$@[\]^‘{|}~ Refer to the ISO 646 Character
Replacements chart in your User Guide to view the character
replacements for each country.
USB PC Keyboard
USA (Default)
Belgium
Denmark
Finland
France

Note: For a complete list of country codes, see the User’s Guide
for your product.
Germany/Austria
Great Britain
Italy
Norway
Spain
Switzerland

Locked Link
If you link a scanner to a base using the Locked Link Mode,
other scanners are blocked from being linked if they are inad-
vertently placed into the base. If you do place a different scan-
ner into the base, it will charge the scanner, but the scanner will
not be linked.
To use a different scanner, you need to unlink the original scan-
ner by scanning the Unlink Scanner bar code.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner bar code with a new
scanner, and place that scanner in the base. The locked link will
be overridden; the broken or lost scanner’s link with the base will
be removed, and the new scanner will be linked.
Unlinking the Scanner
If the base has a scanner linked to it, that scanner must be
unlinked before a new scanner can be linked. Once the previous
scanner is unlinked, it will no longer communicate with the
base. Scan the Unlink Scanner bar code to unlink a scanner.
Locked Link Mode
(Single Scanner)
Override Locked Scanner
Unlink Scanner

Trigger
The following bar codes will allow you to use the scanner in
Manual Trigger - Normal Mode (need to press the trigger to
read) or Presentation mode (the scanner is activated when it
“sees” a bar code).
Suffix
If you want a carriage return after the bar code, scan the Add CR
Suffix bar code. To add a tab after the bar code, scan the Add
Tab Suffix bar code. Otherwise, scan the Remove Suffix bar
code to remove the suffixes.
Manual Trigger - Normal
(Default)
Presentation Mode
Add CR Suffix
Add Tab Suffix
Remove Suffix