Honeywell Xenon 1902h User manual

Enhanced Xenon™ 1902H
Cordless Area-Imaging Scanner for Healthcare
Quick Start Guide
Rev D
8/16
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
日本語 : www.honeywellaidc.com をご覧ください。
한글 www.honeywellaidc.com 로이동합니다 .

Note: Refer to your User’s Guide for information about cleaning your
device.
For localized language versions of this document, go to
www.honeywellaidc.com.
Get Started
Turn off the computer’s power before connecting the base, then
power up the computer once the base is fully connected. Once the
base is connected and powered up, follow the Link the Scanner
instructions (below) to link the scanner to the base.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

Connect the Scanner
USB:

Keyboard Wedge:
RS232 Serial Port:

Link the Scanner
Use the following procedure to configure all scanners so they auto-
matically connect to the base.
1. Scan the bar code on the base.
2. Place the scanner into the base.
3. Power cycle the base to complete the link and establish
communication between the base and scanner.
When the scanner is in the base, the green LED on the base flashes
to indicate the scanner’s battery is charging.
Unlink the Scanner
If the base has a scanner linked to it, that scanner must be unlinked
before a new scanner can be linked. Once the previous scanner is
unlinked, it will no longer communicate with the base. Scan the
Unlink Scanner bar code to unlink a scanner.
Reading Techniques
The view finder projects an aiming
beam that should be centered over
the bar code, but it can be posi-
tioned in any direction for a good
read.
Hold the scanner over the bar code,
pull the trigger, and center the aim-
ing beam on the bar code.
Unlink Scanner

The aiming beam is smaller when the scanner is closer to the code
and larger when it is farther from the code. Hold the scanner close
to smaller bar codes, and farther away from large bar codes to get a
proper read.
If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.
Note: If the scanner beeps 3 times when scanning a bar code, the
link has not been established. If the scanner beeps once, the
link has been established.
Standard Product Defaults
The following bar code resets all standard product default settings.
USB Serial
Scan the following code to program the scanner to emulate a regular
RS232-based COM Port. If you are using a Microsoft® Windows®
PC, you will need to download a driver from the Honeywell website
(www.honeywellaidc.com). The driver will use the next available
COM Port number. Apple® Macintosh computers recognize the
scanner as a USB CDC class device and automatically use a class
driver.
Note: No extra configuration (e.g., baud rate) is necessary.
Standard Product Defaults
USB Serial

USB PC Keyboard
Scan the following code to program the scanner for a USB PC Key-
board.
Epic
Scan the following bar code to configure your device to communi-
cate with an Epic software application.
After scanning this code, you must put the scanner into the base or
scan the linking bar code on the base or Access Point to relink your
scanner.
USB PC Keyboard
EMR Application

Meditech®
Scan the following bar code to configure your device to communi-
cate with a Meditech software application.
After scanning this code, you must put the scanner into the base or
scan the linking bar code on the base or Access Point to relink your
scanner.
Quiet Operations
The following codes configure the scanner and base to quiet modes
for scanning that does not disturb resting patients.
Meditech Application

Silent Mode with Flashing LED
Scan the following bar code to completely silence the base and
scanner. When a bar code is scanned, the LED and aimer flash
5 times. Green indicates a good scan, red indicates a bad
scan.
Silent Mode with Long LED
Scan the following bar code to completely silence the base and
scanner. When a bar code is scanned, the LED and aimer
remain solidly lit for 1 second. Green indicates a good scan,
red indicates a bad scan.
Silent Mode with Flashing LED
Silent Mode with Long LED

Very Low Beeper (Nighttime Mode)
The following bar code silences the base, and sets the scanner
for a very low beep when reading bar codes. After scanning
this code, the base beep, base and scanner power up beep,
and scanner linking sounds are all silenced. When a bar code
is scanned, the scanner emits a very soft beep.
Low Beeper (Daytime Mode)
Scan the following bar code to set all sounds to on, but at a low
volume. The scanner beep, base beep, base and scanner
power up beep, and scanner linking sounds are all set to low
volume.
Nighttime Mode
Daytime Mode