Honeywell Voyager 1602g User manual

Voyager 1602g
Wireless Area-Imaging Pocket Scanner
Quick Start Guide
5/15
Preliminary
Draft4/27/15
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Idźna stronę: www.honeywellaidc.com po quick start w języku polskim.
Перейти на русскоязычный сайт www.honeywellaidc.com.
Pro češtinu jdi na www.honeywellaidc.com.
Pre slovenčinu choďna www.honeywellaidc.com
Para Português, acesse www.honeywellaidc.com.br.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
查看繁体版请登陆 www.honeywellaidc.com
한글 www.honeywellaidc.com 로이동합니다 .
ʲʡʤʱʸʢʬʡʺʩʸˬʺʡʥʺʫʡʨʰʸʨʰʩʠʤʸʺʠʬʸʥʡʲwww.honeywellaidc.com.
Çäè´á Åàˆ moc.cdiallewyenoh.www ààú¬ ÇàõÑéí¬

Note: Refer to your User’s Guide for information about cleaning your
device.
Getting Started
The scanner’s battery must be fully charged before the first use. It
can be charged using a power supply or by connecting the USB
cable to a computer.
Charging via Power Supply:
Note: The power supply must be ordered separately, if needed.

Connecting the Scanner to a USB port:
Turn off the computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.

Battery Charge Indicator
When the battery is charging, the small LED at the top left of the
scanner flashes orange. When the battery is fully charged, this LED
is solid green.
Reading Techniques
The scanner projects an aiming
beam that should be centered over
the bar code, but it can be posi-
tioned in any direction for a good
read.
Hold the scanner over the bar code,
press the button, and center the
aiming beam on the bar code.
The aiming beam is smaller when
the scanner is closer to the code and larger when it is farther from
the code. Hold the scanner close to smaller bar codes, and farther
away from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.
Note: If the scanner beeps 3 times when scanning a bar code, the
link has not been established. If the scanner beeps once, the
link has been established.
Standard Product Defaults

Scan the following bar code to reset the scanner to all standard
product default settings.
Standard Product Defaults
Using the Scanner
with Bluetooth Devices
The scanner can be used either with a Honeywell Access Point
(AP01-XXXBT) or with other Bluetooth devices. Those devices
include personal computers, laptops, and tablets.
1. Scan the Bluetooth HID Keyboard Connect bar code below.
Bluetooth HID Keyboard Connect
2. Set your personal computer, laptop, or tablet so it searches for
other Bluetooth devices. (Refer to your device’s User’s Guide for
pairing instructions.)
3. Once your personal computer, laptop, or tablet has located the
scanner, select the scanner name. Some personal computers,
laptops, or tablets will automatically pair with the scanner. If your
device automatically pairs with the scanner, it displays a

successful pairing message and you do not need to continue to
the next step.
4. If your personal computer, laptop, or tablet does not
automatically pair with the scanner, a PIN is displayed. This PIN
must be scanned within 60 seconds. You must quickly scan
Bluetooth PIN Code below, then scan the numeric bar code(s) for
the PIN code from the Programming Chart, then scan the Save
bar code.
Bluetooth PIN Code
Your personal computer, laptop, or tablet should now be paired with
the scanner.
Disconnect from Host and Connect to an
Access Point
If your scanner has been connected directly to an iPad, smart
phone, or laptop, you must disconnect it in order to communicate
with an Access Point. Scan the Bluetooth HID Keyboard Discon-
nect bar code to unlink the scanner from the currently linked host.
Scan the linking bar code on the Access Point to relink the scanner.
Bluetooth HID Keyboard Disconnect

Keyboard Country
Your keyboard layout default is a US keyboard. To change this lay-
out, refer to the following chart for your keyboard country. Scan the
Program Keyboard Country bar code, then scan the numeric bar
code(s) for the appropriate Country Code from page 2, then scan
the Save bar code.
By default, national character replacements are used for the follow-
ing characters: #$@[\]^‘{|}~
Refer to the ISO 646 Character Replacements chart in your User’s
Guide to view the character replacements for each country.
Program Keyboard Country
Country Code Scan Country Code Scan
Belgium 1Italy 5
Denmark 8Norway 9
Finland 2Spain 10
France 3Switzerland 6
Germany/Austria 4USA (Default) 0
Great Britain 7
Save
Note: For a complete list of country codes, see the User’s Guide for
your product at our website, www.honeywellaidc.com.

Suffix
If you want a carriage return after the bar code, scan the Add CR
Suffix bar code. To add a tab after the bar code, scan the Add Tab
Suffix bar code. Otherwise, scan the Remove Suffix bar code to
remove the suffixes.
Add CR Suffix
Remove Suffix
Add Tab Suffix
For additional prefix and suffix settings, see the User’s Guide for
your product at our website, www.honeywellaidc.com.
Add Code ID Prefix to all Symbologies
Scan the following bar code if you wish to add a Code ID prefix to all
symbologies at once.
Add Code ID Prefix To All Symbologies
(Temporary)
Note: For a complete list of Code IDs, see the User’s Guide for your
product at our website, www.honeywellaidc.com.

Function Code Transmit
When this selection is enabled and function codes are contained
within the scanned data, the scanner transmits the function code to
the terminal. Charts of these function codes are provided in your
User’s Guide. When the scanner is in keyboard wedge mode, the
scan code is converted to a key code before it is transmitted.
Enable
(Default)
Disable

Data Format Editor Instructions
The following are abbreviated instructions for entering a data format.
For complete instructions refer to your User’s Guide, available at our
website, www.honeywellaidc.com.
1. Scan the Enter Data Format symbol.
2. Primary/Alternate Format: scan 0for Primary Format
3. Terminal Type: scan 099 for any terminal type
4. Code I.D.: scan 99 for any bar code type
5. Length: scan 9999for any length bar code.
6. Editor commands: use the Programming Chart that follows.
7. Scan Save to save your entries.
Enter Data Format
Clear All Data Formats
Save