Honeywell HD3DSX User manual

Document 800-13600V1 – Rev A – 05/2013
HD3DS(X) HD3HRS(X) Indoor Minidome Camera Quick Installation Guide 1
This document describes how to install the HD3DS(X) and the HD3HRS(X) minidome
cameras. The camera can be installed to a wall or ceiling using one of the following
methods:
• surface mount
• flush (in-ceiling) mount
• pendant mount
Important Safety Instructions
•Read and keep these instructions.
• Please ensure that your installation area can safely support the weight of the camera.
• Do not install the camera in extreme temperature conditions. Only use the camera where
temperatures are within the limits shown in the specifications section of the user guide.
Be especially careful to provide ventilation when operating under high temperatures.
• Do not aim the camera towards an extreme light source to prevent damaging the CCD.
• This camera is rated for indoor operation; do not expose this camera to rain or moisture.
• Do not touch the camera lens, dome or bezel (front glass plate).
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
WARNING Installation and servicing should be performed only by
qualified and experienced technicians to conform to all local codes and to
maintain your warranty.
WARNING This device is configured for 12 V DC or 24 V AC
operation. Do not connect to a higher voltage. Use only with NRTL-approved
Class 2 power supplies.
Package Contents
Before you begin, check that you have the following items:
Camera Overview
Installing the Camera
Disassembling the Camera
1. Insert a coin into the notch on the camera base
and twist. Set the dome cover aside.
2. Grasp the gimbal base with one hand and the base
skirt with the other and twist the gimbal base
clockwise to remove it from the skirt.
3. Remove the main camera assembly from the base skirt.
Connecting the Cables
Connect the power and video cables.
Mounting the Camera
Surface Mount
1. Pre-drill the mounting holes using the
supplied mounting template as a guide.
2. Attach the base skirt to the mounting surface
using the supplied mounting screws and
anchors.
Note For added support, you can attach the base
skirt to a 2S junction box.
3. Re-attach the main camera assembly to the
base skirt. Twist the gimbal base counterclockwise to lock it in place.
4. Adjust the gimbal position, field of view, and focus as desired
(see Setting Up the Camera).
Flush Mount
1. Cut a hole in the mounting surface using the supplied mounting template as a guide.
2. Insert the main camera assembly through the hole.
• HD3DS(X) or HD3HRS(X) camera
• 2nd video cable
• DC power jack flying lead
• Hardware kit consisting of four (4)
mounting screws and anchors
• Mounting template
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
DO NOT OPEN
RISK OF ELECTRIC SHOCK
Power Cable
24 V AC
Base Skirt
Video Cable
Mounting Screws
Gimbal Base
Main Camera Assembly
Camera Control Board
Power Board
Gimbal
Lens
Dome Cover
1
Locked Unlocked
24 V AC
CCTV Monitor
Unlocked Locked

www.honeywellvideo.com
+1.800.323.4576 (North America only)
https://honeywellsystems.com/ss/techsupp/index.html
Document 800-13600V1 – Rev A – 05/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by
any means without written permission from Honeywell. The information in this publication is believed to
be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences
resulting from the use thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate such changes.
3. With a Phillips screwdriver, push and turn the three (3) spring-loaded screws
ninety degrees (90°) to rotate the wing tabs outward.
4. Adjust the gimbal position, field of view, and focus as desired
(see Setting Up the Camera).
Pendant Mount
1. Attach the pendant mount to the mounting surface using appropriate hardware
(not supplied).
2. Attach the base skirt to the pendant mount.
3. Attach the main camera assembly to the base skirt.
4. Adjust the gimbal position, field of view, and focus as desired
(see Setting Up the Camera).
Setting Up the Camera
Adjusting the Gimbal
Rotate and tilt the gimbal as desired.
Adjusting the Field of View
1. Loosen the zoom screw.
2. Move the screw right to zoom in
(tele) or left to zoom out (wide).
3. Tighten the zoom screw to lock
it in place.
Adjusting the Focus
1. Loosen the focus screw.
2. Move the screw right to focus near or left to focus far.
3. Tighten the focus screw to lock it in place.
Configuring the Camera Settings
Connect to a spot monitor.
Configure the camera settings using the OSD. Refer to the 3 Inch High Resolution Indoor
Minidome Camera Configuration Guide for detailed configuration instructions. Use the
controller joystick to navigate through the OSD menu structure.
Replacing the Dome Cover
Re-attach the dome cover to the camera base by lining up the yellow stickers and snapping
the dome cover into place.
Regulatory Statements
FCC Compliance
Information to the User: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the essential
protection requirements of the EMC directive 2004/108/EC, conforming to the requirements of
standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60065 for electrical equipment
safety.
WEEE (Waste Electrical and Electronic Equipment)
2
Rotation 360° Tilt 70°
Pan 355°Pan 360°
Zoom
Focus
OSD Joystick
2nd Video Out
Spot Monitor
1. EXPOSURE
LENS
BACKLIGHT
AGC
SENSE-UP
3D DNR
EXIT JUMP
2. COLOR
WB MODE
RED GAIN
BLUE GAIN
COLOR MODE
EXIT JUMP
3. DAY&NIGHT
D&N MODE
NIGHT C.
NIGHT A.
EXIT JUMP
4. FUNCTION
MIRROR
SHARPNESS
GAMMA
SLC
NIGHT-UP
EXIT JUMP
5. MOTION
AREA SET
SENSITIV.
SHOW INDI.
EXTER OUT
EXIT JUMP
6. PRIVACY
MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
MASK 7
MASK 8
EXIT JUMP
7. SETUP
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
COMMUNICA.
FACTORY SET
EXIT JUMP
8. EXIT
SAVE&EXIT
EXIT
Correct disposal of this product (applicable in the European Union and other
European countries with separate collection systems)
This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
3