Honeywell HISD-1181W User manual

© 2012 Honeywell International Inc. All rights reserved.
Honeywell
HD HS Dome Camera
Operation Manual
HISD-1181W/2201W

Honeywell
i
Contents
1Introduction ...................................................................................................................1
Performance Characteristics Features .....................................................................1
Features of IP Module..............................................................................................1
2Hardware Installation.....................................................................................................2
System Requirement................................................................................................2
Installation Environment...........................................................................................2
Installation environment requirements............................................................... 2
Recommended operating environment.............................................................. 2
Hardware installation steps................................................................................ 2
Network connection........................................................................................... 3
Connection Instruction .............................................................................................4
3Operating Guide for IP Camera.....................................................................................5
Search IP Camera....................................................................................................5
Download and Install ActiveX...................................................................................5
Liveview...................................................................................................................7
Record Playback......................................................................................................9
Set System Parameters(Configure)........................................................................12
Local config......................................................................................................12
Remote config..................................................................................................13
Audio........................................................................................................................13
Video Settings ..........................................................................................................14
Network Settings.......................................................................................................18
Storage Settings.......................................................................................................26
Alarm Settings ..........................................................................................................29
Dome Camera ..........................................................................................................33
System .....................................................................................................................39
4Appendix.....................................................................................................................43
Main Technical Parameters....................................................................................43
Network Interface of IP Camera.............................................................................45
Default Network Parameters ..................................................................................45
Apply for DDNS domain name service ...................................................................46
IP camera DDNS introduction...........................................................................46
DDNS function of IP camera.....................................................................................46
The DDNS process of IP camera is as follow:...........................................................46
Apply for DDNS domain name service..............................................................46

Honeywell
ii
Visit IP camera under different network environments............................................48
LAN..................................................................................................................48
Static IP....................................................................................................................48
Dynamic IP...............................................................................................................49
Internet.............................................................................................................50
FAQs .....................................................................................................................55

Honeywell
iii
CAUTION
•Non-technician should not try to operate this dome device before reading this
manual carefully.
•Cut the power supply off before operating the dome device to avoid damage
caused by mal-operation.
•Interior of the dome device are precision optical and electrical instruments. Heavy
pressure, shock and other incorrect operations should be prevented. Otherwise,
may cause damage to product.
•All the wiring of the dome device should be conducted strictly according to the
wiring instruction. When necessary, thunder-proof, surge-proof and other
protecting measures should be carried out.
•Please do not use the product under circumstances where the limits exceed the
maximum specified temperature, humidity or power supply specifications.
•Contents in this manual may be different from the edition that you are using.
Should any unsolved problem occur given that the product is used according to
this manual, please contact our technical support department or your product
suppliers.
•The default communication protocol for this dome device is PELCO-D, and baud
rate is 2400 BIT/s, dome address is No.1.

Honeywell
iv
Packing List
Check if the packing contents match the packing list on receiving the products. The packing
list is as below:
Part Quantity
IP HD Dome Camera 1
Wall bracket 1
Camera Shroud 1
Rubber Blanket 1
Foam-rubber cushion 1
Bag of screws 1
Certificate 1
Compact Disk 1
Power Supply 1
Contact your local retailer if anything is missing in your package.

Honeywell
1
1 Introduction
Performance Characteristics Features
•Pan 360°continuous rotation.\
•Tilt 0°～90° rotation
•Pan manual operation speed can be 0.1° /S to 300° /S
•Tilt manual operation speed can be 0.1° /S to 120° /S
•256 preshot positions.（A fixed position that aimed by the dome camera, which
can be set and revised by user arbitrarily）
•The maximum running speed when preshot is being called can reach 400°/S with
accuracy of ±0.1°
•Two groups of preset tours
•Vertical auto flip function with 10° automatic forward tracking
•Easy installation interface
•Power supply: AC 24V2A
•Pass environmental protection grade IP66
Features of IP Module
•With the built-in Web Server, it fully supports IE monitoring, configuration and
updating
•Support fixed bit rate and variable bit rate
•UPNP function.
•Support DDNS and PPPOE
•Support image capturing、remote video recording、play back function
•Support H.264 and JPEG video compression format
•Motion detect
•Linkage alarm output, image capturing and video recording functions based on
alarm event
•Transmitting images through FTP or Email as alarm event

Hardware Installation
2
2 Hardware Installation
System Requirement
•LAN or Internet serve
•Internet Explorer: 5.0 or higher version
•CPU: PⅢor higher
•Internal Memory：512M or bigger
•Display：17 inch
•Monitor Resolution: 1024×768
•Operating system：Windows NT、Windows2000、Windows XP
Installation Environment
Installation environment requirements
Far away from high-temperature resource and environment; improper place for ventilation;
avoid install on shaky place.
Recommended operating environment
Temperature：-10 ~ +60 C
Humidity：5% ~ 80% RH
Hardware installation steps
Please make sure LAN or Internet is in working order before installation of the IP camera.
Steps:
•Unpack the box to check the goods.
•Take out all goods which needed for installation from the box.
•Take out the black acrylic cover and insert SD card as figures shown below:

Honeywell
3
Figure 2-1
Figure 2-2
•Connect related cables according to actual need ( Power line, reticle, audio
frequency line etc.).
•Connect the power supply.
Network connection
•LAN connection
Using one network line to connect IP camera with concentrator or switchboard of
the LAN.
•WAN connection
Using one network line to connect IP camera with Router or XDSL Modem/Cable
Modem.
•See figs below
Micro SD card installation
site
Insert Micro SD card
following the direction
shown in Figure 2-2

Hardware Installation
4
•Connect the power supply.
The IP camera will automatic start once power is connected.
Connection Instruction
RESET+/GND
ALARM OUT NO+ / ALARM
Audio_ out (white)
Audio_ in (yellow)
NC+ / ALARM OUT_NC-
Power Line
ALARM_IN+ / GND-
Network terminal

Honeywell
5
3 Operating Guide for IP Camera
Search IP Camera
Use search engine to find camera IP address. After install NVS software, user can find
search tool. Its icon like . Once click that icon, user can get IP address and
other relevant parameters of all cameras.
Connected to the host machine. And all those information is changeable through double click
the IP address.
Figure 3-1
Download and Install ActiveX
You need to install ActiveX Control when you visit IP camera for the first time through IE
browser.
ActiveX installing method:
Download installation

Operating Guide for IP Camera
6
Input the IP address of IP camera in Internet Explorer to enter into login page (see Figure 3-
2), type in user name and password (default user name and password are : admin):
Figure 3-2
After enter into the live view interface, click the “File”.
Figure 3-3
File download dialogue box pops up, click Run or Save to download ActiveX, after download
it, double-click the downloaded file “xdview.exe” to install it. After installation completes, a
message “Register OCX success！” will appear (see Figure 3-4 ).
Figure 3-4

Honeywell
7
Liveview
See Figure 3-5 for the interface of “Liveview”
Figure 3-5
In the Liveview interface, users can do operations like Snap, Record, Replay, Call, Listen,
Alarm, Log, Local Zoom of Image, Full-screen Viewing, PTZ and Lens Control.
•Snap: click “Snap”, snap the current image and save it in .JPG format
automatically to the storage directory of snapped images. The default path is
C:\XDNVS.
•Record: Manual image recording, automatically record current images and save
them in .264 format to the storage directory of recorded images after the recording
function turned on. The status icon for Record shows as: .
•Replay: Click “Replay”, the play back page will pop up for searching and playback
of recorded files or snapped pictures.
•Call: After turn on the audio talkback switch, the talkback between PC and IP
camera can be performed given that audio talkback device is installed to the IP
camera. The status icon for Call shows as: .
•Listen: After switch on the monitoring switch, PC can monitor the sound at the
device end. The status icon for Listen shows as: .
•Alarm: When there is an alarm, double-click [Alarm] to cancel the alarm manually.
•Log: Allow users to search for operations and alarm log. The maximum capacity is
512 entries of message, when the number of entries exceeds 512, system will
delete records of the earliest date automatically.
•Zoom: This feature allows the manual drag and drop of video display area to
realize partial zoom in.

Operating Guide for IP Camera
8
•Full Screen: Display images in full-screen, right click to exit full screen mode.
•PTZ Control:Allows four-directional rotation, automatic adjustment of PTZ
rotation speed(see Figure 3-6).
•Lens Control: Allows PTZ operations like Zoom, Focus, Aperture, Light, Clip,
Preset set, and Preset Call(see Figure 7).
•Dome: See Figure 8 for the interface of “Dome”
•Preset No.: You can set, delete and call presets.
•Figure Scan: Support two groups of figure scan. If you enable this function, it can
record the operations of PTZ, but the operations don’t include PTZ rotate
automatically, preset tour, P&Z scan, PTZ reset, mostly special presets or call by
menu.
•PAN Flip: Rotate horizontally 180°.
•Zero Detection: If you set azimuth zero, the device will be rotated to thereafter
power on and tests by itself when click this button. If you delete the azimuth zero,
it will be rotated to the machine zero. You can set it in Dome CameraPTZ
Setting.
•Left/Right/Up/Down Limit: The dome can be only rotated in the range as you set
when it is scanning.
•Preset Tour 1/2: Call preset tour 1 or 2, you can set preset tour in Dome
CameraPTZ Setting.
•P&T SCAN: Call P&T scan, you can set preset tour in Dome CameraPTZ
Setting.
•Stop: Stop the PTZ’s operation.
Figure 3-6
Figure 3-7

Honeywell
9
Figure 3-8
Record Playback
Click enter into video playback page (see Figure 3-9).
Figure 3-9
Users can search for recorded image files or snapped pictures in local PC or storage device
according to date.

Operating Guide for IP Camera
10
•Date: Users can select certain date to perform recorded image file or snapped
picture searching, click “date” button , data selection page will pop up(see
Figure 3-10):
Figure 3-10
•PC: Users can select certain date to perform recorded image file or snapped
picture (stored in local PC) searching.
•SD Card: Users can select certain date to perform recorded image file or snapped
picture (stored in device SD card) searching.
•File List: Shows the recorded image files or snapped pictures searched in the File
List.
The way to search for recorded image files or snapped pictures of a specific period (see
Figure 3-11):
Click “《” icon to turn to previous year
Click “ 》” icon to turn to next year
Click “〈” icon to turn to previous month
Click “ 〉” icon to turn to next month

Honeywell
11
Figure 3-11
•Play: Choose the recorded image or snapped picture in file list, right click the file
or picture or click “play” button to play. The contents will be displayed in the
right window, users can view the playing information and control the process(see
Figure 3-12).
Figure 3-12
•Download: Select the recorded files or snapped pictures searched from SD card
in the file list, click “download” button to download the files to PC.
•Download information: Users can view the information downloaded after clicking
“Download”(see Figure 3-13).
Select to search for record files or snapped
pictures in PC or device SD card
The record file list searched is displayed on the left
The picture list searched is displayed on the right
The left side stands for hour, each grid means one hour
The right side stands for minute, each grid means 2
minutes
Yellow indicates the selected search period
Blue indicates there are files and pictures searched
of the selected period
Display the files and pictures searched of the
selected period

Operating Guide for IP Camera
12
Figure 3-13
Click Pause to pause download manually，click Start to continue to download the
unfinished files，click Delete to delete the downloaded files，click Close to close the
download information interface. If you close the Download Information window and click
, you can continue to view the information about download.
Set System Parameters(Configure)
Local config
See Figure 3-14 for the interface of “Local config”.
Figure 3-14
PC live view parameter setting

Honeywell
13
•Code stream: set video stream for PC live preview, preferred stream and
alternate stream are selectable. The parameters of preferred and alternate stream
can be set up in “Video Settings”.
•Preview mode: users can choose Real time priority or Fluency priority mode
according to their needs.
•Reset Mosaic: select this option to make image quality better, but CPU usage rate
will be higher at the same time.
PC storage Parameter
•Record file packing time: set packing time of record files for local PC when it is
recording.
•Record file path: set the storage directory for local records and snapped files.
The default path is C:\XDNVS.
After you set these parameters, please click Save to make them valid.
Remote config
Audio
See Figure 3-15 for the interface of “Audio setting”.
Figure 3-15
•Enable audio: turn on or turn off the audio of IP camera, When there is no need
for audio, close audio input to save DSP resource and network resource. Audio is
disabled by default.
•Input type: You can choose MIC or Line In input.
•Type: Support three types of audio compressed format:G.726,G.711A,G.711U.
•Sampling: HISD-1181W supports audio sample rates of 8k and 32; HISD-2201W
supports 8k, 16k and 32k.

Operating Guide for IP Camera
14
•Input Volume: Adjust the device’s input volume to control the volume of Listen.
•Output Volume: Adjust the device’s output volume to control the volume of Call.
After you set these parameters, please click Save to make them valid.
Video Settings
Text Overlay
See Figure 3-16 for the interface of “Text Overlay”:
Figure 3-16
•Title: the name of video channel, displayed at the bottom left of image (movable),
maximum characters allowed: 32.
•Color: You can choose different colors for the text.
•OSD: Display or not to display Title, Date, Time, Week, Date Format and
Frame/Bitrate of channels.
•Position: Can adjust the display position of video title and Date, Time, Week.
After you set these parameters, please click Save to make them valid.
Video Coding
See Figure 3-17, 3-18 for the interface of “Video Coding”: