Honeywell JOSI-DBC012-N11 User manual

Document 800-01605 – Rev A – 04/08
Installation Guide
ACUIX™
Fixed Dome

Revisions
Issue Date Revisions
A 04/08 New document

ACUIX TM Fixed Dome User Guide
Rev A Document 800-01605
04/08
3
Contents
1 Installing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Overview of the Installation Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing the Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
In-Ceiling (dropped) Housing Installation . . . . . . . . . . . . . . . . . . . . . . . 16
In-Ceiling Housing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Indoor Pendant Housing Installation . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing the Camera Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Installing the Inner Dome Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the Lower Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
In-Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Pendant Lower Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2 Adjusting the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the Focal Length and Focusing the Lens . . . . . . . . . . . . . . . . . . . . . . . 27
Vari-focal Auto Iris Configuration (Color Cameras) . . . . . . . . . . . . . . . . . . . . . . . 27
Color Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Wide Dynamic Range (WDR) Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Adjusting the Line Lock (Vertical Phase) For External Sync Reference . . . . . . . . . . . . . 31
Adjusting the Backlight Compensation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Appendix A Solving Common Technical Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Appendix B Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Rev A Document 800-01605
04/08
Contents
4

ACUIX TM Fixed Dome User Guide
Rev A Document 800-01605
04/08
5
Figures
Figure 1-1 Installation Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 1-2 Installing a Dropped Ceiling Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 1-3 In-Ceiling Hole Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 1-4 In-Ceiling Housing Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 1-5 Spacing Wing Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 1-6 Pendant Dome Housing Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 1-7 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 1-8 Power Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 1-9 Camera Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 1-10 Slide Inner Dome Liner into the Lower Dome . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 1-11 Slide Lanyard into Clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 1-12 In-Ceiling Lower Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 1-13 Pendant Lower Dome Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 2-1 Recommended Camera Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-2 Gimbal Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-3 Color Camera Switch Settings (Vari-focal Auto Iris Lens Shown). . . . . . . . . . . . . . . 28
Figure 2-4 WDR Camera Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Rev A Document 800-01605
04/08
Figures
6

ACUIX TM Fixed Dome User Guide
Rev A Document 800-01605
04/08
7
Tables
Table 1-1 ACUIX™Fixed Dome Housing Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 1-2 ACUIX™Fixed Dome Lower Dome Model Numbers . . . . . . . . . . . . . . . . . . . . . . 14
Table 1-3 ACUIX™Fixed Dome Cameras and Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 2-1 Color Camera DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 2-2 White Balance Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 2-3 Manual Shutter Speed Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 2-4 WDR Camera DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Rev A Document 800-01605
04/08
Tables
8

Document 800-01605 Rev A 9
04/08
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a Class B
digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference. For example, try
reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver,
or connecting the equipment to an outlet on a different circuit.
Caution Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
European Compliance Statement
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
Caution Users of the product are responsible for checking and complying with all federal, state and
local laws and statutes concerning the monitoring and recording of video and audio signals.
Honeywell Video Systems shall not be held responsible for the use of this product in violation
of current laws and statutes

10
Explanation of Graphical Objects
Important Safety Instructions
READ INSTRUCTIONS - All safety and operating instructions should be read before the unit is operated.
1. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference.
2. HEED WARNINGS - All warnings on the unit and in the operating instructions should be adhered to.
3. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed.
4. CLEANING - Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
5. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may result in
the risk of fire, electric shock, or injury to persons.
6. WATER AND MOISTURE - Do not use this unit near water or in an unprotected outdoor installation, or any area
classified as a wet location.
7. ACCESSORIES - Only use accessories specified by the manufacturer. Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult and serious
damage to the equipment. Use only with a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's
instructions and should use a mounting accessory recommended by the manufacturer. Wall or shelf mounting
should follow the manufacturer's instructions and should use a mounting kit approved by the manufacturer.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
9. POWER SOURCES - This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or
local power company.
10. OVERLOADING - Do not overload outlets and extension cords as this can result in a risk of fire or electric shock.
11. POWER-CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords, plugs, and convenience
receptacles.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the enclosure of the product that may be of sufficient
magnitude to constitute a risk of electric shock to the person.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance servicing instructions in the literature accompany the product.

Document 800-01605 Rev A 11
04/08
12. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
13. DAMAGE REQUIRING SERVICE - Unplug the unit from the outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or moisture.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the enclosure has been damaged.
f. When the unit exhibits a distinct change in performance - this indicates a need for service.
14. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
15. SAFETY CHECK - Upon completion of any service or repairs to this unit, ask the service technician to perform
safety checks to determine that the unit is in proper operating condition.
16. LIGHTNING AND POWER LINE SURGES - For added protection of this unit when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage
to the unit due to lightning and power-line surges.
17. HEAT - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
18. INSTALLATION - Install in accordance with the manufacturer’s instructions. Do not install the unit in an extremely
hot or humid location, or in a place subject to dust or mechanical vibration. The unit is not designed to be
waterproof. Exposure to rain or water may damage the unit.
Prior to installation and use of this product, please observe the following cautions and warnings.

12
Caution
Warnings
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLEPARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DONOT OPEN
WARNING: Installation and servicing must be performed by qualified personnel in accordance with
current IEE wiring regulations.
WARNING: The PSU must be wired to a double pole fuse spur with 3mm separation. The 3A fuse spur
must be located close to the PSU.
WARNING: Using replacement parts or accessories other than the original manufacturers may invalidate
the warranty.
WARNING: To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance
with the installation instructions.

Document 800-01605 Rev A 13
04/08
1
Installing the Camera
This guide covers how to install the ACUIX™fixed dome camera. It includes instructions
to install the housing mount, how to mount the camera in the housing, how to connect the
wiring, and how to adjust the image.
The ACUIX™ product line offers housings for indoor applications. The indoor application
features a pendant housing for wall mounting and an indoor in-ceiling housing. There are
also adapters available for corner and pole mounting.
This guide provides instructions for mounting the different types of housings. Each
housing contains an interface board that provides wiring for video on coax or unshielded
twisted pair, and control data on shielded or unshielded twisted pair (RS485) or over
coax.
Related Documents
For more information about topics that are relevant to the subject of this guide, see the
documents listed below:
Document title Part number
HDXWM1 Decorative Wall Mount Install Guide 900.0868
HDCM1 Indoor Pendant Mount Install Guide 900.0869

14
Installing the Camera
Models
Refer to the following table for the ACUIX™fixed dome model numbers.
Table 1-1 ACUIX™Fixed Dome Housing Model Numbers
Model Number Description
HDH1B FG, HSG, HDX FIXED, PNDT, COAX, BLACK
HDH1D FG, HSG, HDX FIXED, IN CEILING, COAX
HDH1P FG, HSG, HDX FIXED, PNDT, COAX, WHITE
HDH2B FG, HSG, HDX FIXED, PNDT, UTP (Unshielded Twisted Pair),
BLACK
HDH2D FG, HSG, HDX FIXED, IN CEILING, UTP
HDH2P FG, HSG, HDX FIXED, PNDT, UTP, WHITE
Table 1-2 ACUIX™Fixed Dome Lower Dome Model Numbers
Model Number Description
HDB00D0CB FG, LWR DOME, IN CEILING, CLEAR, BLACK TRIM
HDB00D0CW FG, LWR DOME, IN CEILING, CLEAR, WHITE TRIM
HDB00D0GB FG, LWR DOME, IN CEILING, GOLD, BLACK TRIM
HDB00D0GW FG, LWR DOME, IN CEILING, GOLD, WHITE TRIM
HDB00D0KB FG, LWR DOME, IN CEILING, CHROME, BLACK TRIM
HDB00D0KW FG, LWR DOME, IN CEILING, CHROME, WHITE TRIM
HDB00D0SB FG, LWR DOME, IN CEILING, SMOKED, BLACK TRIM
HDB00D0SW FG, LWR DOME, IN CEILING, SMOKED, WHITE TRIM
HDB00P0CB FG, LWR DOME, PNDT, CLEAR, BLACK TRIM
HDB00P0CW FG, LWR DOME, PNDT, CLEAR, WHITE TRIM
HDB00P0GB FG, LWR DOME, PNDT, GOLD, BLACK TRIM
HDB00P0GW FG, LWR DOME, PNDT, GOLD, WHITE TRIM
HDB00P0SB FG, LWR DOME, PNDT, SMOKED, BLACK TRIM
HDB00P0SW FG, LWR DOME, PNDT, SMOKED, WHITE TRIM

ACUIX TM Fixed Dome User Guide
Document 800-01605 Rev A 15
04/08
Table 1-3 ACUIX™Fixed Dome Cameras and Lenses
Overview of the Installation Process
Model Number Description
HDC1AN Color, 480TVL, NTSC with 5-50mm MI (Manual Iris) lens
HDC1BN WDR, 480TVL, NTSC with 5-50mm MI lens
HDC2AN Color, 480TVL, NTSC with 5-50mm AI (Automatic Iris) lens
HDC2BN WDR, 480TVL, NTSC with 5-50mm AI lens
Task See section
1. Install the housing in a ceiling or wall. See “Installing the Housing” on page 16.
2. Mount the ACUIX™to a ceiling or wall. See “Connecting the Cables” on page 20.
3. Connect the cable to the camera board. See “Connecting the Cables” on page 20.
4. Secure the gimbal into the
ACUIX™base.
See “Installing the Camera Assembly” on
page 21.
5. Adjust the camera settings. See “Adjusting the Camera” on page 25.
6. Secure the cover. See “Installing the Lower Dome” on
page 23.

16
Installing the Camera
Figure 1-1 Installation Components
Installing the Housing
In-Ceiling (dropped) Housing Installation
WARNING! Installation must be performed by qualified technical
personnel and must be in accordance with all national and
local mechanical and electrical codes.
Perform the following steps to install a dropped ceiling housing (see Figure 1-2):
Figure 1-2 Installing a Dropped Ceiling Housing
Base
Gimbal
Inner Dome Liner
Dome Cover
In-Ceiling Pendant
Dropped Ceiling Plate
Field wiring access hole
Drywall
ceiling
Housing
Lower dome mounting
posts (3 places) Attach lanyard to
lower dome

ACUIX TM Fixed Dome User Guide
Document 800-01605 Rev A 17
04/08
1. Select the location of the housing. Each ACUIX™ Fixed requires either a 17 to 28
VAC or an 11 to 16 VDC power source measured at the housing. Each ACUIX™
Fixed has a power consumption of 3.5W for the color cameras or 4.5W for the WDR
cameras. Ensure a 24 VAC/12 VDC @ 0.2A power source is available. See
Appendix B, Cable Guidelines on page 35 for maximum wiring distances to the
dome.
2. Remove the ceiling panel at the dome location.
3. Place the ceiling tile on the dropped ceiling plate. Trim the ceiling tile so you can
press the ceiling tile into the dropped ceiling plate.
4. Cut a hole in the ceiling tile flush with the hole in the center of the plate.
5. If necessary, secure a safety cable (supplied by the installer) to a building support
structure. Honeywell recommends using a 3/32” plastic coated aircraft cable.
6. Insert the housing in the ceiling
a. Adjust the turning screws on the wing tabs to ensure the space between the
wing tabs and housing flange is greater than the thickness of the ceiling.
b. Position the wing tabs flat against the housing. Insert the housing through the
hole in the ceiling tile. Using a Phillips screwdriver, turn the two screws in the
housing clockwise to rotate the tabs out and tighten the tabs against the ceiling
tile. The recommended maximum torque is 1–1.25 N-m or 0.74–0.92 lbf-ft or
8.85–11.06 lbf-in.
c. Insert the housing through the hole in the ceiling, ensuring the wing tabs are flat
against the housing. The recommended maximum torque is 1–1.25 N-m
7. See Connecting the Cables on page 20 for information on connecting the field
wiring to the interface board in the housing.
8. See Installing the Camera Assembly on page 21 for information on installing the
camera assembly and Installing the Lower Dome on page 23 for information on
installing the lower dome.
In-Ceiling Housing Installation
WARNING! Installation must be performed by qualified technical
personnel and must be in accordance with all national and
local mechanical and electrical codes.
Perform the following steps to install an ACUIX™in-ceiling housing:
1. Select the location of the housing. Each ACUIX™ Fixed requires either a 17 to 28
VAC or an 11 to 16 VDC power source measured at the housing. Each ACUIX™
Fixed has a power consumption of 3.5W for the color cameras or 4.5W for the WDR
cameras. Ensure a 24 VAC/12 VDC @ 0.2A power source is available. See
Appendix B, Cable Guidelines on page 35 for maximum wiring distances to the
dome.
2. Cut a 7/15-16” (201.2 mm) diameter hole in the ceiling.

18
Installing the Camera
Figure 1-3 In-Ceiling Hole Dimensions
3. If the ceiling is drywall or plaster, Honeywell Video Systems recommends sealing
the entire perimeter of the ceiling cut-out with tape or a plastic channel (provided by
the installer). This prevents dust and material from dropping from the ceiling.
4. If required, secure a safety cable (supplied by the
installer) to a building support structure. Honeywell
recommends using a 3/32” plastic coated aircraft cable.
Attach the safety cable (from the building support
structure) to the housing by:
a. Threading the safety cable through a looping
sleeve,
b. Through the lanyard clip (see Figure 1-4),
c. Back through the looping sleeve, and then
d. Crimping the looping sleeve to secure the safety
cable.
5. Insert the housing in the ceiling.
Figure 1-4 In-Ceiling Housing Installation
a. Ensure that the space between the wing tabs on the housing and the housing
flange is greater than the thickness of the ceiling tile. Adjustments are made by
turning the screws on the wing tabs; clockwise decreases the space between
the tab and the housing flange and counterclockwise increases the space
between the tab and the housing flange. Make sure the wing tabs on the
housing are staggered so the tabs are not at the same height.
7-15/16” (201.2 mm)
Looping
sleeves (2)
Attach to building
structure
Attach to lanyard
clip
Cable entry hole
Lanyard clip
Wing screws

ACUIX TM Fixed Dome User Guide
Document 800-01605 Rev A 19
04/08
Figure 1-5 Spacing Wing Tabs
b. Position the wing tabs flat against the housing. Insert the housing through the
hole in the ceiling (some jostling is required). Using a Phillips screwdriver, turn
the two screws in the housing clockwise to rotate the tabs out and tighten the
tabs against the ceiling. The recommended maximum torque is 1–1.25 N-m
(Newton meters) or 0.74–0.92 lbf-ft (pound-force-foot) or 8.85–11.06 lbf-in
(pound-force-inch).
6. Refer to Connecting the Cables on page 20 for information on connecting the field
wiring to the interface board in the housing.
7. See Installing the Camera Assembly on page 21 for information on installing the
camera assembly and Installing the Lower Dome on page 23 for information on
installing the lower dome.
Indoor Pendant Housing Installation
WARNING! Installation must be performed by qualified technical
personnel and must be in accordance with all national and
local mechanical and electrical codes.
Perform the following steps to install an ACUIX™pendant housing on a Honeywell Video
Systems indoor wall dome mount or ceiling dome mount. See Figure 1-6.
1. Select the location of the housing. Each ACUIX™ Fixed requires either a 17 to 28
VAC or an 11 to 16 VDC power source measured at the housing. Each ACUIX™
Fixed has a power consumption of 3.5W for the color cameras or 4.5W for the WDR
cameras. Ensure a 24 VAC/12 VDC @ 0.2A power source is available. See
Appendix B, Cable Guidelines on page 35 for maximum wiring distances to the
dome.
2. Install the mount using the instructions provided with your specific mount.
3. Run the field wiring (control data, video, power, and alarm) through the mount. The
wiring must extend at least one foot (0.3 m) past the pipe for wiring purposes. See
Cable Guidelines on page 35 for detailed wiring information.
4. Locate the pendant housing.

20
Installing the Camera
Figure 1-6 Pendant Dome Housing Installation
a. Insert the field wiring (data, power, video, and alarm) from the mount through
the threaded nipple on the pendant housing.
b. Carefully thread the housing into the mount.
5. See Power Cable Connection on page 21 for information on connecting the field
wiring to the terminal strips on the interface board in the housing.
6. See Installing the Camera Assembly on page 21 for information on installing the
camera assembly and Installing the Lower Dome on page 23 for information on
installing the lower dome.
Connecting the Cables
1. Follow Figure 1-7 for the wiring connection.
Figure 1-7 Wiring
2. Connect the power/video cable from the gimbal assembly to the camera board (see
Figure 1-8).
1.5” NPT threaded nipple Route field wiring
from mount
Coaxial Cables UTP Cables
Video: Unshielded
Twisted Pair wire
Video: female BNC
Power
red +
connect to red + black -
connect to ground Power: 2.1 mm
male jack center