Honeywell H34S-IC User manual

Document 800-16667 – Rev A – 01/2014
H34S-IC In-Ceiling Mount
Quick Installation Guide
This document describes how to install an equIP®Series H3D S Series indoor or H4D S Series
rugged IP minidome camera in a suspended ceiling using the H34S-IC in-ceiling mount.
CAUTION Installation and servicing should be performed only by
qualified and experienced technicians to conform to all local codes and
to maintain your warranty.
Package Contents
Before you begin, check that you have received all of the parts listed below. If any parts are
missing or damaged, contact your dealer immediately.
You will also need drilling tools and a Phillips screwdriver (not supplied).
In-Ceiling Mount Dimensions
• In-ceiling mount
• Trim ring
•Template
• Security Torx key
• Quick Installation Guide
3.23 in.
(82.1 mm)
Ø 7.87 in.
(200 mm)
Ø 4.53 in.
(115 mm)
Ø 1.73 in.
(44 mm)
Ø 5.91 in.
(150 mm)
60°
1.34 in.
(34 mm)

2 | H34S-IC In-Ceiling Mount Quick Installation Guide
www.honeywell.com/security
Preparing the Camera
1. Loosen the two captive security screws on the dome cover using the supplied Torx key
and remove the dome cover from the camera base.
2. Remove the inner cover from the camera assembly. Press both sides of the inner cover to
release it from the camera assembly.
3. Remove the screw securing the camera assembly to the camera base using a Phillips
screwdriver (not supplied).
4. Remove the camera assembly from the camera base by pressing the tabs on the sides of
the camera assembly. Store the camera assembly in the product box while you attach the
camera base to the in-ceiling mount.
Note For rugged cameras only: There are two cable entry holes on the camera base. Install
the conduit plug in the hole you are not using.
Indoor Dome Rugged Dome
Indoor Dome Rugged Dome
Indoor Dome Rugged Dome

800-16667 - A - 01/2014
| 3
Attaching the Camera to the In-Ceiling Mount
1. Align the three captive M3 screws on the in-ceiling mount with the mating screw holes on
the camera base. Make sure the cable entry hole on the in-ceiling mount is lined up with
the cable entry hole on the camera base.
2. Tighten the screws on the in-ceiling mount to secure it to the camera base.
Preparing the Ceiling
1. Select the location where you want to install the camera. The installation area must be able
to safely support the weight of the camera.
2. Place the adhesive-backed template on the ceiling at the selected location and then cut
around it (176 mm diameter).
Installing the Camera in the Ceiling
1. Run the camera wiring (power, network, video,
audio, alarm) through the camera base.
2. Insert the in-ceiling mount and attached camera
base into the ceiling hole, and then tighten the
screws on the in-ceiling mount until the camera
base is flush against the ceiling tile.
CAUTION Do not overtighten the
screws. Overtightening can damage the
in-ceiling mount. If using a power tool, set the
slip clutch to the lowest setting.
3. Retrieve the camera assembly from the product box, line up the tabs on the camera
assembly with the guides on the camera base, and then slide the camera assembly onto
the camera base until the tabs lock securely in place.
4. If you want, insert a microSDHC memory card (up to 32 GB, Class 10) into the
microSDHC card slot on the camera assembly.
Top View Side View
Bottom View (Indoor Dome)

www.honeywell.com/security
[phone] (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
© 2014 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Document 800-16667 – Rev A – 01/2014
5. Connect the camera wiring. Refer to the quick installation guide that came with the camera
for details.
6. Access the camera’s browser-based viewer (Honeywell Viewer) to view images, or,
alternatively, connect a coaxial cable from a portable service monitor to the BNC
connector on the camera control board.
7. Adjust the pan and tilt setting of the camera as desired. Loosen the locking screw on
the camera assembly gimbal to adjust the tilt angle and then retighten it. The tilt angle
is adjustable between –10° and 90°. The pan adjustment range is nearly 360° and the
rotation angle range is nearly 270°.
8. If you connected a coaxial cable to the camera in
step 5, remove it.
9. Replace the inner cover on the camera assembly.
10. Reinstall the screw securing the camera
assembly to the camera base.
11. Replace the dome cover on the camera base.
12. Tighten the two captive security screws on the
dome cover using the supplied Torx key.
13. Align the three holes in the trim ring with the
retaining nut on the in-ceiling mount, and then
snap the trim ring in place to complete the
installation.