Honeywell FocusPRO User manual

FocusPRO®Wireless Thermostats
® U.S. Registered Trademark.
Copyright © 2008 Honeywell International Inc.
All rights reserved.
Wireless control for up to 3 Heat/2 Cool heat pump systems or up to
2 Heat/2 Cool conventional systems.
MERCURY NOTICE: If this product is replacing a control that contains mercury in a
sealed tube, do not place the old control in the trash. Contact your local waste
management authority for instructions regarding recycling and proper disposal.
Must be installed by a trained, experienced technician. Read these instructions
carefully. Failure to follow these instructions can damage the product or cause a
hazardous condition.
Español: vea la página 9 • Français : voir la page 17
Non-zoned systems
• Single thermostat with wireless
Equipment Interface Module
(EIM).
Zoned systems
• Up to 4 thermostats with
TrueZONE™panel & wireless
adapter.
Installation guide for:
Need Help?
For assistance with this product please visit http://customer.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
Installation
Guide

Install batteries
1
Press CONNECT button at EIM or wireless adapter and wait for green flashing
light, then follow steps below.
Install quick reference card
Install 2 fresh AA batteries
2
FocusPRO®Thermostat Installation Guide
Programmable models only
Link thermostat(s) to wireless network
2
Wireless Setup
01
NextBack
Wireless Setup
36 52
Back Next
Wireless SetupWireless Setup
Back
Installation with EIM: Press NEXT (leave
zone number set to zero).
Installation with TrueZONE panel: Press
▲or ▼to set a zone number for this
thermostat (1 to 4), then press NEXT.
Installation with EIM: Press NEXT.
Installation with TrueZONE panel: Press
▲or ▼to select a name for this zone, then
press NEXT (see list of names on page 6).
Press CONNECT to establish a link to the
wireless network.
After a brief pause, the confirmation
screen at left should be displayed, to
verify that the wireless connection has
been established.
Press DONE to display the home screen.
Wireless SetupWireless Setup
Connected
Done
Zone nameZone number
Connect
If E1 appears, see error codes on page 3.

3
Español: vea la página 9 • Français : voir la page 17
Customize thermostat (installer setup)
3
Function Setting
Press ▲or ▼to change setting
(see tables on pages 4-6)
Press NEXT to display next
function screen
Press DONE to save & exit.
Follow the steps below to begin installer setup. At each function screen,
press ▲or ▼to change the setting as desired, then press NEXT to advance to
the next function screen.
See tables on pages 4-6 for a description of options for each function.
10
Back NextDone
01
BackDone Next
To begin, press and hold the FAN and ▲buttons
until the display changes (about 3 seconds).
Thermostat error codes
If E1 appears during setup, check error code number (right side of screen):
29 You are attempting to connect a thermostat to an incompatible device.
30 Zone number must match zone panel number (must be zero for EIM systems).
31 Verify that this zone number is configured at the zone panel as an RF thermostat.
33 Faulty return air sensor. Check wiring or replace sensor as needed.
34 Low signal strength. Move wireless device to a different location and try again.
38 Make sure Connected light is flashing and you are 2+ feet away from EIM or
wireless adapter.
FAN

4
FocusPRO®Thermostat Installation Guide
Installer setup tables
0
1
2
3
5
6
7
8
9
10
12
13
14
Zone number
System type
Changeover valve
(O/B terminal)
Fan control
(conventional heat)
Stage 1 heat cycle
rate (CPH= cycles
per hour)
Stage 2 heat
cycle rate (CPH)
Stage 3 heat
cycle rate (CPH)
Emergency heat
cycle rate (CPH)
Stage 1 compres-
sor cycle rate
Stage 2 compres-
sor cycle rate
Manual/Auto
changeover
Adaptive Intelligent
Recovery
Temperature
display
0No zoning (single thermostat used with THM5320R EIM)
[Options: select zone 1, 2, 3 or 4]
0 1 heat/1 cool conventional
1 1 heat/1 cool heat pump (no aux. heat)
2 Heat only (includes Series 20)
3 Heat only with fan
4 Cool only
5 2 heat/1 cool heat pump
6 2 heat/2 cool conventional
7 2 heat/1 cool conventional
8 1 heat/2 cool conventional
9 2 heat/2 cool heat pump
10 3 heat/2 cool heat pump
0 O/B terminal controls valve in cooling
1 O/B terminal controls valve in heating
0 Gas/Oil heat (equipment controls fan)
1 Electric furnace (thermostat controls fan)
5 Gas or oil furnaces (less than 90% efficiency)
1 Steam or gravity systems
3 Hot water systems & furnaces of over 90% efficiency
9 Electric furnaces
[Cycle rate options: 1 to 12 CPH]
5 Gas or oil furnaces (less than 90% efficiency)
1 Steam or gravity systems
3 Hot water systems & furnaces of over 90% efficiency
9 Electric furnaces
[Cycle rate options: 1 to 12 CPH]
5 Gas or oil furnaces (less than 90% efficiency)
1 Steam or gravity systems
3 Hot water systems & furnaces of over 90% efficiency
9 Electric furnaces
[Cycle rate options: 1 to 12 CPH]
9 Electric furnace
[Cycle rate options: 1 to 12 CPH]
3 Recommended cycle rate
[Cycle rate options: 1 to 6 CPH]
3 Recommended cycle rate
[Cycle rate options: 1 to 6 CPH]
0 Manual (User options: Heat/Cool/Off)
1 Automatic (User options: Heat/Cool/Auto/Off)
Applies only to Model TH6320
0Off
1On
0 Fahrenheit
1 Celsius
Setup functions Settings & Options (factory default in bold)

5
Español: vea la página 9 • Français : voir la page 17
15
16
26
27
28
32
33
35
Compressor off
time (minimum)
Schedule format
Auxiliary heat
control
Maximum heat
setpoint
Minimum cool
setpoint
Temp. display
offset (indoor)
Temp. display
offset (outdoor)
Humidity display
offset (outdoor)
5 5 minutes (Heat On/Cool On flashes during off time)
[Options: 0 to 4 minutes]
Applies only to Model TH6320
0 Weekday/weekend program schedule
1 Weekday/Saturday/Sunday program schedule
Applies only to Model TH5320
0 Comfort **
1 Economy
90 Max. heat temperature setting is 90°F (32°C)
[Options: 40 to 90°F (4.5 to 32°C)]
50 Min. cool temperature setting is 50°F (10°C)
[Options: 50 to 99°F (10 to 37°C)]
0 Thermostat displays actual temperature
[Options: -3 to +3°F offset (-1.5 to +1.5°C)]
0 Thermostat displays actual temperature
[Options: -5 to +5°F offset (-2.5 to +2.5°C)]
3 Thermostat displays actual humidity
[Other options: 0 = -15%, 1 = -10%, 2 = -5%,
4 = 5%, 5 = 10%, 6 = 15% offset]
** See page 6
Installer setup tables
Setup functions Settings & Options (factory default in bold)

36
39
90
Zone name
Wireless setup
RESET
52 Thermostat
Installer setup tables
Setup functions Settings & Options (factory default in bold)
0 Disconnect thermostat from wireless system
1 Thermostat is connected to wireless system
0Noreset
1 Reset installer options & program schedule to factory
default settings
1 Basement
2 Bathroom
3 Bathroom 1
4 Bathroom 2
5 Bathroom 3
6 Bedroom
7 Bedroom 1
8 Bedroom 2
9 Bedroom 3
10 Bedroom 4
11 Boat House
12 Bonus Room
13 Computer Room
14 Den
15 Dining Room
16 Exercise Room
17 Family Room
18 Fireplace
19 Foyer
20 Game Room
21 Garage
22 Great Room
23 Guest Room
24 Gym
25 Kid’s Room
26 Kitchen
27 Kitchen 1
28 Kitchen 2
29 Laundry Room
30 Library
31 Living Room
32 Lower Level
33 Master Bath
34 Master Bed
35 Media Room
36 Music Room
37 Nursery
38 Office
39 Office 1
40 Office 2
41 Pantry
42 Play Room
43 Pool Room
44 Porch
45 Rec Room
46 Sewing Room
47 Spa
48 Storage Room
49 Studio
50 Sun Room
51 Theater
52 Thermostat
53 Upper Level
54 Utility Room
55 Walk-in Closet
56 Wine Cellar
57 Workshop
Special functions
Comfort/Economy (Setup Function 26):
If you choose Comfort, auxiliary heat will respond quickly to meet the temperature setpoint. If
you choose Economy, the system will wait longer. Auxiliary heat will be activated only if the
setpoint is not reached within a reasonable time.
6
FocusPRO®Thermostat Installation Guide

7
Español: vea la página 9 • Français : voir la page 17
System test
02 0
BackDone Next
To begin, press and hold the ▲and ▼buttons
until the display changes (about 3 seconds)
Press ▲or ▼ to check system status
Press NEXT to advance to next test
Press DONE to terminate system test
02
04
10
20
30
40
70
Wireless test
Return air sensor
Heating system
Emergency
heating system
Cooling system
Fan system
Thermostat
information
(for reference only)
0Off
1 Test radio signal (after a brief pause, screen displays 1-10
to show signal strength; 5 or higher recommended)
Screen displays return air temperature if device is installed
and working properly (EIM only)
0 Heat and fan turn off
1 Heat turns on
2 Stage 2 heat turns on
3 Stage 3 heat turns on
0 Heat and fan turn off
1 Heat and fan turn on
0 Compressor and fan turn off
1 Compressor and fan turn on
2 Stage 2 compressor turns on
0 Fan turns off
1 Fan turns on
71 Software revision number (major revisions)
72 Software revision number (minor revisions)
73 Configuration identification code (major)
74 Configuration identification code (minor)
75 Production configuration date code (week)
76 Production configuration date code (year)
System Test System Status
Follow the procedure below to test for proper operation.
System test
number
System
status
CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection (minimum off time)
is bypassed during testing. To prevent equipment damage, avoid cycling the compressor
quickly.

8
FocusPRO®Thermostat Installation Guide
Detach wallplate Mount wallplate and thermostat
Mount thermostat
4
Replacing system components
To replace a thermostat, install batteries and follow the procedures on page
2 to link it to the wireless network. If necessary, modify settings as needed
(see tables on pages 4-6).
After installing a new EIM or zone panel, you must re-set the thermostat to
communicate with the new equipment, as described below:
1 Press and hold the thermostat FAN and ▲buttons for 3 seconds.
2 Press BACK twice to display Function 39 (wireless setup).
3 Press ▼to change Function 39 setting to 0 (disconnect from system).
4 Follow the procedures on page 2 to relink to system.
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
http://yourhome.honeywell.com
Automation and Control Solutions
69-2092EFS-01
06-2008
© 2008 Honeywell International Inc.
® U.S. Registered Trademark.
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Scarborough, Ontario M1V 4Z9
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.

Termostatos inalámbricos FocusPRO®
® Marca registrada de los EE. UU.
Copyright © 2008 Honeywell International Inc.
Todos los derechos reservados.
Control inalámbrico para sistemas de bomba de calor de hasta 3 calentadores/2
refrigeradores o sistemas convencionales de hasta 2 calentadores/2 refrigeradores.
AVISO SOBRE MERCURIO: si este producto reemplaza un control que contiene mer-
curio en un tubo sellado, no coloque el control anterior en la basura. Comuníquese
con la oficina de gestión de residuos de su localidad para obtener instrucciones sobre
cómo reciclar o desechar el producto de manera adecuada.
La instalación debe ser realizada por un técnico capacitado y experimentado.
Lea detenidamente estas instrucciones. Si no sigue estas instrucciones, corre el riesgo
de dañar el producto o de provocar una situación peligrosa.
Guía de
instalación
del sistema
Español: vea la página 9 • Français : voir la page 17
Guía de instalación para:
Sistemas no zonificados
• Un solo termostato con módulo
de interfaz inalámbrico del
equipo (EIM).
Sistemas zonificados
• Hasta 4 termostatos con panel
TrueZONE™y adaptador
inalámbrico.
¿Necesita ayuda?
Consulte sobre este producto en http://customer.honeywell.com
o llamando sin cargo a atención al cliente de Honeywell 1-800-468-1502

10
FocusPRO®Thermostat Installation Guide
Instalación de las baterías
1
Instale la tarjeta de referencia
rápida
Instale 2 baterías
AA nuevas
Solo en modelos programables
Presione el botón CONNECT en el EIM o en el adaptador inalámbrico y espere a
que la luz verde destelle, luego siga los pasos que se detallan a continuación.
Conexión del o de los termostatos a la red inalámbrica
2
Wireless Setup
01
NextBack
Wireless Setup
36 52
Back Next
Wireless SetupWireless Setup
Back
Instalación con el EIM: presione NEXT (deje
configurado el número de zona en cero).
Instalación con el panel TrueZONE:
presione ▲o ▼para configurar un número
de zona para este termostato (de 1 a 4),
luego presione NEXT.
Instalación con el EIM: presione NEXT.
Instalación con el panel TrueZONE:
presione ▲o ▼para elegir un nombre
para esta zona, luego presione NEXT (vea la
lista de nombres en la pág. 14).
Presione CONNECT para establecer una
conexión a la red inalámbrica.
Después de una pausa breve, debe apare-
cer la pantalla de confirmación a la
izquierda, para verificar que se estableció
la conexión inalámbrica.
Presione DONE para mostrar la pantalla
principal.
Wireless SetupWireless Setup
Connected
Done
Nombre de la zonaNúmero de la zona
Connect
Si aparece E1, vea los códigos de error en la
pág. 11.