Honeywell PRO TH3210D User manual

Product Application
This thermostat provides electronic control of 24 VAC heat pump systems with aux-
iliary heat (2 heat/1 cool).
Power Type
• Battery power
• Collll]]on wire
• (-k)mmon wire with battery backup
System Settings
• Heat, Oft, Cool, Em Heat
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before
beginning installation.
MERCURY NOTICE
if this product is replacing a control that contains mercury in a sealed tube, do not
place the old control in the trash. Contact your local waste management authority for
instructions regarding recycling and proper disposal.
® U.S. Registered Trademark. Patents pending.
Copyright O 2005 Honeywell International Inc. All rights reserved.

PRO TH3210D Non-programmable Digital Thermostat
r,
Installation
Pre4nstallation checklist ............... .2
WMlplate installation ..................... .3
Wiring. ............................................ :4
Wiring diagrams .............................. 5
Installer Setup
Battery installation ......................... .6
Thermostat mounting ................... .6
Installer setup ................................. ./"7
Installer system test ....................... .7
Appendices
Quick reference to controls ............ 9
Quick reference m display .............. 9
Compressor protection ................. .9
In case of difficulty ...................... 10
Accessories. ................................... 11
Specifications ................................ 11
InstNI the thermostat about 5 feet (1.5m) above the floor in an area
wRh good air circulation at average temperature.
\
D
Do not instaR in locations where the thermostat can be affected by:
* Drafts or dead spots behind doors and in corners
. Hot or cold air from ducts
. Sunlight or radiant heat from appliances
* Concealed pipes or chimneys
* Unheated/uncooled areas such as an outside wall behind the thermostat

Installation Guide
Package contents
Check to make sure your package includes the lk)llowing items:
• PROTH3210D digital thermostat (wallplate attached to back)
• Operating manual
• wall anchors and mounting screws (2 each)
• AA alkaline batteries (2)
Required tools &supplies
• No. 2 Phillips screwdriver
• Small pocket screwdriver
• Drill
• Drill bit (3/16" for drywall, 7/32" for plaster)
• Hammer
• Pencil
• Electrical tape
• Level (optional)

PRO TH3210D Non-programmable Digital Thermostat
Grasp top and bottom of wallplate
and pull to remove from thermostat. Remove the wallplate from the ther-
mostat as shown at left, then fk_llow
directions below _k>rmounting.
1 Pull wires through wire hole.
2 Position wallplate on wall, level and
mark hole positions with pencil.
3 Drill holes at marked positions as
shown below, then tap in
supplied wall anchors.
4 Place wallplate over anchors, insert
and tighten mounting screws.
Drill 3/16" holes for drywall.
Drill 7/32" holes for plaster,

Installation Guide
CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage.
Disconnect power before wiring.
%,-- _ _ _, ,=, ,=, _ _, _ , _%
l,JE AuxY G 0 LR B
/
Terminal
block
NOTES
Cterrainal
The C (common wire) terminai is optional
when thermostat is powered by batteries.
Lterminal
Heat pump reset. L terminai is powered con-
tinuously when thermostat is set to Em Heat.
Wire specifications
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
Wiring
1Ix)osen screw terminals, insert
wires into terminal block, then re-
tighten screws.
2 Push excess wire back into the
wall opening. Keep wires in shaded
area as shown at left.
Plug the wall opening with non-
flammable insulation to prevent
drafts from affecting thermostat
opemtion.
Terminal Designations
E Emergency heat relay.
Aux Auxiliary heat relay.
Y Compressor contactor.
G Fan relay:
O Heat pump changeover valve
energized in cooling.
LHeat pump reset.
R Power wire [_om secondary
side of system transformer.
B Heat pump changeover valve
energized in heating.
CCommon wire fron3 seconda W
side of system transformer.

PRO TH3210D Non-programmable Digital Thermostat
M
1 Power supply. Provide disconnect means and overload protection as required.
2 Optional 24 VAC common connection.
3Use either O or B terminals for changeover valve.
4 L terminal is powered continuously when thermostat is set to Em Heat.
5 Install field jumper between E and Aux if there is no emergency heat relay.
L1
L2 (HOT)
I
HEAT CHANGEOVER VALVE
RELAY
COOL CHANGEOVER VALVE
FAN RELAY ]
--'[COMPRESSOR CONTACTOR_
AUXILIARY HEAT RELAY
4EMERGENCY HEAT RELAY_
m
/
Io e • ® o • • o ®1
E Aux Y G 0 L R B C
A AA A,&

Installation Guide
Connect common
side of transformer
to "C" terminal
AC Power
The thermostat can be powered by 24
VAC powel, or by batteries.
To wire the thermostat R)rAC power,
connect the common side of the
transfbrmer to the "C" terminal as
shown at left.
Battery Power
The thermostat (_;*,11be powered by
batteries alone or, if used with AC
power, can provide backup power to
the displ W during power interruptions.
Install batteries in back of thermostat
(optional if AC powered).
To Mount Thermostat
Align the 4 tabs on the wallplate with
corresponding slots on the back of the
thermostat, then push gently until the
thermostat snaps in place.

PRO TH3210D Non-programmable Digital Thermostat
Follow the procedure below to configure the thermostat to match the installed
heating/cooling system, and customize feature operation as desired.
Prose and hold both buttons
Function Setting
number
To begin, press and hold the A and Y
buttons until the display changes Press V to change settings
Press A to advance to next function
Press and hold T_, to exit and save settings
Setup Function
6Auxiliary heat
cycle rate (CPH)
8Emergency heat
cycle rate (CPH)
9 Compressor
cycle rate (CPH)
Settings & Options
5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
9 For electric furnaces
[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]
9 For electric furnaces
1For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
5 For gas or oil furnaces of less than 90% efficiency
[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]
Recommended for most compressors
[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]
14 Temperature 0Fahrenheit
display 1 Celsius
15 Compressor
protection 5Five-minute compressor off time **See page 9 [Other options: 0, 1, 2, 3 or 4-minute off time]
After completing the installer setup above, press the & button again to begin a
system test (see next page).

Installation Guide
Follow tile procedure below to test tile heating and cooling system.
System test System status
number
1System switch
1 Set SYSTEMswitch to Heat.
2 Press Wto turn on and check systems (see table, below).
3 Press V until systems turn off.
4 Set SYSTEMswitch to Em Heat and repeat steps 2-3 above.
5 Set SYSTEMswitch to Cool and repeat steps 2-3 above.
5 Press and hold _V'A to terminate test at any time.
System Test System Status
10 Heating system
20 Emergency heat
30 Cooling system
70 Thermostat
information
(for reference only)
0 Compressor and fan turn off.
1 Compressor and fan turn on.
2 Auxiliary heat turns on.
0 Heat and fan turn off.
1 Heat and fan turn on.
2 Auxiliary heat turns on.
0 Compressor and fan turn off.
1 Compressor and fan turn on.
71 Software revision number (major revisions)
72 Software revision number (minor revisions)
73 Configuration identification code (major)
74 Configuration identification code (minor)
75 Production configuration date code (week)
76 Production configuration date code (year)
CAUTION: EQUIPMENT DAMAGE HAZARD
Compressor protection (minimum off time) is bypassed during testing. To prevent
equipment damage, avoid cycling the compressor quickly.