Honeywell SmartLine STIW400 User manual

Honeywell Process Solutions
SmartLine Wireless
Temperature and Universal I/O
Transmitters
User’s manual
34-SW-25-04
Revision 1
December 2019

ii SmartLine Wireless Temperature and Universal I/O User's Manual Revision 1
Notices and Trademarks
Copyright 2019 by Honeywell International Inc.
Revisions 1, December 2019
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may be
stated in its written agreement with and for its customers.
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and
specifications in this document are subject to change without notice.
Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.
Other brand or product names are trademarks of their respective owners.
Honeywell Process Solutions
1250 W Sam Houston Pkwy S
Houston, TX 77042

Revision 1 SmartLine Wireless Temperature and Universal I/O User's Manual iii
About This Document
This document describes preparation, operation and maintenance of the SmartLineTM Wireless
Temperature Transmitters. Mounting, installation and wiring are covered in other documents.
Honeywell does not recommend using devices for critical control where there is a single point of failure
or where single points of failure result in unsafe conditions. OneWireless is targeted at open loop control,
supervisory control, and controls that do not have environmental or safety consequences. As with any
process control solution, the end-user must weigh the risks and benefits to determine if the products used
are the right match for the application based on security, safety, and performance. Additionally, it is up to
the end-user to ensure that the control strategy sheds to a safe operating condition if any crucial segment
of the control solution fails.
Revision Information
Document Name
SmartLine Wireless Temperature and
Universal I/O Trasnmitters User's
Manual, 34-SW-25-04
Revision
Number Publication Date
1st Release 1 December 2019
References
The following list of documents are sources of reference for material discussed in this publication.
Document Title Doc #
SmartLine Wireless Temperature and Universal IO
Transmitters
Quick Start Guide
34-SW-25-02
OneWireless R310 Release Notes OWDOC-X252-en-310A
OneWireless R310 Migration Users Guide OWDOC-X258-en-310
OneWireless R310 Field Device Access Point Users Guide OWDOC-X256-en-310
OneWireless R310 Wireless Device Manager Users Guide OWDOC-X254-en-310
OneWireless R300 Experion PKS Integration Guide OWDOC-X259-en-300
OneWireless R300 Wireless LAN Controller Configuration
Guide OWDOC-X255-en-300
OneWireless R300 Network Planning an Installation Guide OWDOC-X253-en-300
OneWireless Network Planning and Installation Guide OWDOC-X253-en-320A

iv SmartLine Wireless Temperature and Universal I/O User's Manual Revision 1
Support and Contact Information
For Europe, Asia Pacific, North and South America contact details, refer to the back page of this
manual or the appropriate Honeywell Support web site:
Honeywell Corporate www.honeywell.com
Honeywell Process Solutions https://www.honeywellprocess.com/*
Training Classes https://www.honeywellprocess.com/en-US/training
Telephone and Email Contacts
Area Organization Phone Number
United States
and Canada Honeywell Inc. 1-800-343-0228 Customer Service
1-800-423-9883 Global Technical Support
Global Email
Support Honeywell Process Solutions [e-mail]

Revision 1 SmartLine Wireless Temperature and Universal I/O User's Manual v
Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.
Symbol Definition
ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a task.
CAUTION
Indicates a situation which, if not avoided, may result in equipment or work (data) on
the system being damaged or lost, or may result in the inability to properly operate
the process.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.
CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could
result in serious injury or death.
WARNING symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS
LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.
ESD HAZARD: Danger of an electro-static discharge to which equipment may be
sensitive. Observe precautions for handling electrostatic sensitive devices.
Protective Earth (PE) terminal: Provided for connection of the protective earth
(green or green/yellow) supply system conductor.
Functional earth terminal: Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to Protective Earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground:Functional earth connection. NOTE: This connection shall be
bonded to Protective Earth at the source of supply in accordance with national and
local electrical code requirements.
Chassis Ground: Identifies a connection to the chassis or frame of the equipment
shall be bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.

vi SmartLine Wireless Temperature and Universal I/O User's Manual Revision 1
Symbol Description
The Factory Mutual®Approval mark means the equipment has been rigorously tested and
certified to FM standards for safety and/or performance.
The Canadian Standards mark means the equipment has been tested and meets applicable
standards for safety and/or performance.
The Ex mark means the equipment complies with the requirements of the European
standards that are harmonized with the 94/9/EC Directive (ATEX Directive, named after the
French "ATmosphere EXplosible").
For equipment declared to meet the CE marking requirements of the European Economic
Area (EEA).
The ISA100 Wireless Compliant logo indicates the device has received ISA100.11a
conformance certification and is registered with the Wireless Compliance Institute, assuring
device interoperability.
CRN Canadian Registration Number

vii SmartLine Wireless Temperature and Universal I/O User's Manual Revision 1
Contents
1. INTRODUCTION................................................................................................... 1
1.1 Purpose.........................................................................................................................................1
1.2 Scope.............................................................................................................................................1
1.3 OneWireless network overview ..................................................................................................1
1.4 Security Considerations..............................................................................................................1
1.5 About the transmitter...................................................................................................................3
1.6 Physical Characteristics..............................................................................................................5
2. PREPARATION AND QUICK START .................................................................. 7
2.1 Introduction ..................................................................................................................................7
2.2 Set up the Network.......................................................................................................................7
2.3 Transmitter Quick Start ...............................................................................................................7
3. INSTALLATION.................................................................................................... 9
3.1 Installation Site Evaluation .........................................................................................................9
3.2 Environmental Conditions: .........................................................................................................9
3.3 Transmitter Weights and Dimensions......................................................................................10
3.4 Installation drawing number tables..........................................................................................13
3.5 Conduit / Cable Entries..............................................................................................................14
Summary.............................................................................................................................................................14
3.6 Mounting Summary....................................................................................................................15
3.7 Rotate transmitter housing .......................................................................................................18
3.8 Rotate display.............................................................................................................................19
Tools required .....................................................................................................................................................19
Procedure............................................................................................................................................................19
Display adjustment..............................................................................................................................................19
3.9 Antenna adjustment and mounting..........................................................................................21
Requirements......................................................................................................................................................21
Integral antenna ..................................................................................................................................................21
3.10 Remote antenna......................................................................................................................23
Outdoor installation warnings..............................................................................................................................23
Choosing a Mounting Location............................................................................................................................24
Site Selection ......................................................................................................................................................24
Mounting the Antenna.........................................................................................................................................25
Directional mounting procedure...........................................................................................................................26
Omnidirectional mounting procedure...................................................................................................................27
Grounding the antenna........................................................................................................................................28
4. SENSOR AND ELECTRICAL CONNECTIONS.................................................. 30
4.1 Introduction ................................................................................................................................30

Contents
Symbol Definitions
viii SmartLine Wireless Temperature and Universal I/O User's Manual Revision 1
4.2 I/O Types .....................................................................................................................................30
4.3 STIW400 Terminal Connections ...............................................................................................31
4.1 STUW750 Terminal Connections..............................................................................................32
4.2 STUW751 Terminal Connections..............................................................................................33
5. POWER AND START UP ................................................................................... 34
5.1 Battery Power Option.................................................................................................................34
Install/Replace batteries......................................................................................................................................34
Battery Pack installation and replacement procedure.........................................................................................36
Battery Pack Test Terminals...............................................................................................................................36
5.2 24V Power Supply Option .........................................................................................................37
24V Power Supply ..............................................................................................................................................38
24V Power Supply Connection/Replacement Procedure....................................................................................39
5.3 Grounding...................................................................................................................................40
24V dc Power Supply Option (DC) System Diagram..........................................................................................40
5.4 Display sequence.......................................................................................................................41
5.5 Provisioning................................................................................................................................41
6. FUNCTION BLOCKS.......................................................................................... 42
6.1 Introduction ................................................................................................................................42
6.2 Block description.......................................................................................................................42
Block types..........................................................................................................................................................42
7. OPERATION....................................................................................................... 43
7.1 Transmitter connection status..................................................................................................43
7.2 Transmitter PV display ..............................................................................................................45
PV status.............................................................................................................................................................46
7.3 Transmitter Channel Configuration..........................................................................................50
Channel Status ...................................................................................................................................................50
Channel Configuration ........................................................................................................................................50
Cold Junction......................................................................................................................................................51
Digital Inputs.......................................................................................................................................................51
7.4 Provisioning Device menus ......................................................................................................52
Overview.............................................................................................................................................................52
Main menu..........................................................................................................................................................52
Security and Node Deployment ..........................................................................................................................52
De-provisioning...................................................................................................................................................54
Read Device Information.....................................................................................................................................54
Advanced Options...............................................................................................................................................56
7.5 Calibrating the transmitter ........................................................................................................57
Overview.............................................................................................................................................................57
Zero Calibration ..................................................................................................................................................57
Two Point Calibration..........................................................................................................................................58
Clearing Calibration ............................................................................................................................................58
8. MAINTENANCE/REPAIR ................................................................................... 59

Contents
Symbol Definitions
Revision 1 SmartLine Wireless Temperature and Universal I/O User's Manual ix
8.1 Introduction ................................................................................................................................59
8.2 Transmitter Firmware upgrade .................................................................................................59
8.3 Preventive maintenance............................................................................................................59
8.4 Replacing Electronics Module..................................................................................................60
Tools required .....................................................................................................................................................60
Procedure............................................................................................................................................................60
8.5 Replacing batteries....................................................................................................................61
When to replace ..................................................................................................................................................61
8.6 Replacing 24V external power module ....................................................................................61
When to replace ..................................................................................................................................................61
8.7 Replacing antenna .....................................................................................................................62
Tools required .....................................................................................................................................................62
Procedure............................................................................................................................................................62
Antenna replacement procedure.........................................................................................................................63
9. PARTS ................................................................................................................ 65
8.8 Transmitter body........................................................................................................................65
Mounting Brackets...............................................................................................................................................66
APPENDIX A - MODBUS ............................................................................................ 68
APPENDIX B - CERTIFICATIONS AND APPROVALS .............................................. 73
Hazardous location certifications.........................................................................................................................74
Battery.................................................................................................................................................................76
24V DC Supply....................................................................................................................................................76
B3. Conditions of Certification ...........................................................................................................77
FM Approval Specific Conditions of Use .............................................................................................................77
CSA, IECEx and ATEX Conditions of Certification..............................................................................................77
Apparatus Marked with Multiple Types of Protection...........................................................................................77
B4. Radio Compliance Information........................................................................................................78
Radio Frequency (RF) statement........................................................................................................................78
European Union restriction..................................................................................................................................78
FCC compliance statements ...............................................................................................................................79
IC compliance statements...................................................................................................................................79

Contents
Tables
x SmartLine Wireless Temperature and Universal I/O User's Manual Revision 1
Tables
Table 3-1: Weights...................................................................................................................10
Table 3-2: Drawing numbers for temperature/UIO transmitters.................................................13
Table 3-3: Conduit entry plugs and cable glands for your transmitter. ......................................14
Table 6-1: Blocks......................................................................................................................42
Table 7-1: Transmitter connection status..................................................................................43
Table 7-2: Transmitter PV display ............................................................................................45
Table 7-3: PV Status................................................................................................................46
Table 7-4: Device status...........................................................................................................47
Table 7-5: SmartLine TEMP-UIO units.....................................................................................49
Table 7-6: Radio menu.............................................................................................................49
Table 7-7: Read Device Information.........................................................................................55
Table 7-8: Advanced Options...................................................................................................57
Table 8-1: Electronics module replacement..............................................................................60
Table 9-1: Transmitter Body Parts............................................................................................65
Table 9-2: Angle and Flat Bracket Parts (Refer to Figure 9-1)..................................................67
Table 9-3: Transmitter Enclosure O-Ring Kit............................................................................67