Honeywell OW-FDAP31 User manual

OneWireless
Field Device Access Point Gen3 User's Guide
OWDOC-X256-en-322A
November 2020
Release 322.1

2
www.honeywell.com
Revision
Supported Release
Date
Description
A
322
November 2020
Initial release of the document
Disclaimer
This document contains Honeywell proprietary information. Information contained herein is to be used solely
for the purpose submitted, and no part of this document or its contents shall be reproduced, published, or
disclosed to a third party without the express permission of Honeywell International Sàrl.
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a purpose and makes no express warranties except as may be stated
in its written agreement with and for its customer.
In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information
and specifications in this document are subject to change without notice.
Copyright 2020 - Honeywell International Sàrl.

3
Contents
1About this guide........................................................................................................................................5
2Introduction to FDAP................................................................................................................................7
2.1 FDAP description..................................................................................................................................................8
2.2 Types of FDAPs ..................................................................................................................................................10
2.3 Physical description of FDAP Gen3.......................................................................................................................11
2.4 Physical description of FDAP1/FDAP2..............................................................................................................12
2.5 Features of FDAP................................................................................................................................................14
2.6 FDAP security.....................................................................................................................................................15
2.7 FDAP compliance information ...........................................................................................................................16
3FDAP Installation .................................................................................................................................... 18
3.1 Prerequisites for installation................................................................................................................................19
3.2 Inspect FDAP and associated hardware ..............................................................................................................20
3.3 Identify FDAP site locations...............................................................................................................................21
3.4 Connect antennas for FDAP Gen3......................................................................................................................22
3.5 Connect antennas for FDAP1/FDAP2 ................................................................................................................23
3.6 Recommendations for remote antenna connections............................................................................................23
3.7 Ground the FDAP Gen3......................................................................................................................................24
3.8 Ground the FDAP1/FDAP2 ................................................................................................................................24
3.9 Mount the FDAP Gen3 .......................................................................................................................................26
3.9.1 Pole mounting ......................................................................................................................................26
3.9.2 Wall or flat surface mounting...............................................................................................................27
3.10 Mount the FDAP1/FDAP2..................................................................................................................28
3.10.1 Pole mounting..................................................................................................................................28
3.10.2 Wall or flat surface mounting ..........................................................................................................29
3.11 Connect power cables and Ethernet cables for FDAP Gen3 ................................................................30
3.11.1 DC power wiring .............................................................................................................................30
3.11.2 Ethernet wiring ................................................................................................................................31
3.12 Connect power cables and Ethernet cables for FDAP1/FDAP2...........................................................32
3.12.1 DC power wiring .............................................................................................................................32
3.12.2 AC power wiring .............................................................................................................................33
3.12.3 Ethernet wiring ................................................................................................................................34
3.13 Power on and startup for FDAP Gen3..................................................................................................36
3.14 Power on and startup for FDAP1/FDAP2 ............................................................................................38
4FDAP Configuration................................................................................................................................31
4.1 Establish connection between WDM and FDAP ................................................................................................32
4.2 Provision an FDAP .............................................................................................................................................33
4.3 Description of FDAP parameters ........................................................................................................................34
5Field Expandable Wireless IO ................................................................................................................41
5.1 Overview.............................................................................................................................................................42
5.2 FEWIO Solution .................................................................................................................................................42
5.3 Converting FDAP Router to FEWIO device.......................................................................................................43
5.4 Connecting Modbus TCP devices to FEWIO device ..........................................................................................47
5.5 Connecting Modbus RTU devices to FEWIO device .........................................................................................48
5.6 Configure FEWIO device in WDM ....................................................................................................................49
5.7 Configuring and Viewing the Modbus Registers................................................................................................51
5.8 Converting FEWIO device to FDAP Router.......................................................................................................54

4
www.honeywell.com
5.9 Experion Integration............................................................................................................................................55
6FDAP Monitoring..................................................................................................................................... 61
6.1 Overview about monitoring ................................................................................................................................62
6.2 Verify connectivity using maps...........................................................................................................................63
6.3 Monitor using Provisioning Handheld device.....................................................................................................64
6.4 Monitor using events...........................................................................................................................................65
6.5 Monitor using reports..........................................................................................................................................66
7FDAP Maintenance and Troubleshooting..............................................................................................67
7.1 Replace an FDAP................................................................................................................................................68
7.2 Remove an FDAP ...............................................................................................................................................69
7.3 Upgrade an FDAP firmware ...............................................................................................................................70
7.4 Troubleshoot an FDAP .......................................................................................................................................71
8Appendix .................................................................................................................................................72
8.1 FDAP GEN3 Technical Specification.................................................................................................................73
8.2 FDAP Technical Specification ............................................................................................................................75
8.1 FDAP Gen3 Dimension Drawing .......................................................................................................................78
8.2 FDAP Dimension Drawing.................................................................................................................................79
8.3 FDAP GEN3 IS Control Drawing.......................................................................................................................80
8.4 FDAP IS Control Drawing (51202683) ..............................................................................................................80
8.5 FDAP GEN3 Label Drawing ..............................................................................................................................82
8.6 FDAP Label Drawing .........................................................................................................................................83
9Notices..................................................................................................................................................... 84
9.1 Documentation feedback.....................................................................................................................................85
9.2 How to report a security vulnerability.................................................................................................................86

5
1About this guide
This document describes the procedures to install, configure, and operate the Field Device Access Point
(FDAP1/FDAP2) and Field Device Access Point Gen3 (FDAP Gen3). FDAP is one of the components in the
OneWireless Network solution for industrial control.
Intended audience
This guide is intended for people who are responsible for planning, administering, and operating the
OneWireless Network. These people include Plant Managers, Process Engineers, and System Administrators.
Prerequisite skills
It is assumed that you are familiar with the operation of OneWireless Network, Experion system software, and
the plant processes which Experion controls, Microsoft Windows operating systems, and network
administration tasks.
How to use this guide
This guide provides guidance on:
•FDAP description
•FDAP installation
•FDAP configuration
•FDAP monitoring
•FDAP maintenance and troubleshooting
Required Honeywell documentation
The following documents and sources contain additional information required for deploying OneWireless
Network. It is recommended to have these documents readily available for reference.
Document
Document ID
Description
OneWireless Network
Planning and Installation
Guide
OWDOC-X253-en-320A
This document provides
information about planning,
designing, and setting up the
OneWireless Network using
WDM, FDAPs, and field
devices.
OneWireless WDM User’s
Guide
OWDOC-X254-en-320B
This document describes the
procedures to provision,
configure, operate, and
monitor an ISA100 Wireless
field device network using
Wireless Device Manager
(WDM).

CONTENTS
6
www.honeywell.com
Document
Document ID
Description
OneWireless Wireless LAN
Controller Configuration
Guide
OWDOC-X255-en-320A
This document provides
information about planning,
designing, setting up, and
configuring a OneWireless
Network using WDM,
FDAPs, Cisco 1552S APs,
and field devices.
FDAP Regulatory
Compliance Guide
—
This document describes the
FDAP Regulatory
Compliance information.
OneWireless Parameter
Reference Dictionary
OWDOC-X260-en-320A
This document provides
information about the
parameters associated with
OneWireless devices.
You can download Honeywell documentation from http://www.honeywellprocess.com website.

2 INTRODUCTION TO FDAP
7
2Introduction to FDAP
Related topics
FDAP description
Types of FDAPs
Physical description of FDAP Gen3
Physical description of FDAP1/FDAP2
Features of FDAP
FDAP security
FDAP compliance information

2 INTRODUCTION TO FDAP
8
www.honeywell.com
2.1 FDAP description
Note that in this document, a reference to wireless field devices include ISA100 Wireless devices,
WirelessHART devices, and Wired HART devices unless otherwise mentioned. Specific device type will be
mentioned as and when applicable.
The Field Device Access Point (FDAP) is a ruggedized industrial radio device intended for use in
hazardous location to provide wireless connectivity for Wireless compatible field devices. As an
industrial meshing access point, FDAP provides secure and reliable wireless coverage for wireless
field devices. It also serves as a routing access point for wireless field devices and is located
between the wired DCS network and wireless-based wireless field devices. Once deployed in the
field, FDAPs self-discover and self-organize into a managed, secure, and redundant wireless field
device mesh network. With FDAPs, wireless field devices do not have to route data from other
field devices. The following figure illustrates how FDAPs are used in a OneWireless Network:
Figure 1: One-Wireless Network
FDAP uses IEEE 802.15.4 standard based radio technology and combines spatial diversity with
advanced error correction schemes to communicate in a complex multi-path environment and in
large communication areas. It has an Ethernet interface for connection to the backbone network
and a wireless compliant radio to connect to the wireless field device network. It is a standalone,
pole mountable, intrinsically safe device, suitable for use in hazardous locations. It is normally
installed in the same area where industrial field devices are installed. FDAP supports 10/100 Mbps
Fast Ethernet and has spatial antenna diversity.

2 INTRODUCTION TO FDAP
9
Table 1: FDAP models
Model numbers
Hazloc Comlinace
Model numbers
Power options FDAP
POE Device Powered Through
OW-FDAP31
FDAP Gen3 certified for Class I
Div1, Zone 0/1
OW-FDAP31
DC = 12 -30VDC & POE
NA
OW-FDAP32
FDAP Gen3 certified for Class I
Div2, Zone 2
OW-FDAP32
DC = 12 -30VDC & POE
NA
FDAP3P
FDAP Gen3 certified for Class I
Div2/Zone2
FDAP3P
POE
AC/DC

2 INTRODUCTION TO FDAP
10
www.honeywell.com
2.2 Types of FDAPs
FDAP as backbone router
FDAP has a radio board and an autonomous power subsystem that operates within a range of DC input. FDAP
supports wireless radio communication, and it does not support Wi-Fi or other radio technologies. The FDAP
may be used for Class I Division 2, Zone 2 and general-purpose applications.
NOTE
AC is only supported in FDAP1/ FDAP2 models.
FDAP as field router
A FDAP can be used as a Field Router (FR). If FDAP is not connected to the physical Ethernet, it functions as a
line powered FR. FDAP as a line powered FR option can be used for extending field mesh into hazardous
environments where normal infrastructure nodes are not suitable. The FDAP may be used as a field router for
Class 1 Division 1, Zone 0/1 applications that require IS protection methods and design techniques. This also
supports RS485 communication to transmit data from Modbus slaves over Wireless ( FEWIO role).
R

2 INTRODUCTION TO FDAP
11
2.3 Physical description of FDAP Gen3
FDAP Gen3 enclosure
The FDAP Gen3 has a rugged die-cast aluminum enclosure for outdoor use. The enclosure and all auxiliary
components are designed to meet IP66 and IP67 ratings for protection against dust and water ingress. The
enclosure has two N-type bulkhead connectors for antenna spatial diversity in the FDAP radios. The two of the
half-inch rigid conduit hub has a gasket to seal out water and dust. A rigid conduit hub, internal and external
ground studs, and a removable cover are provided for field installation. It has an internal Bluetooth Low
Energy (BLE) module and this allows the device to be commissioned in the field. Six status LED’s provide
information about power, device health, Bluetooth, RS485 and Ethernet communication. The enclosure may be
mounted on a pole or on a flat surface such as a wall using the available optional mounting brackets. The
enclosure measures approximately 20 cm x 13 cm x 7 cm (L x W x H).
Figure 2.1: FDAP GEN3 WITH LIGHTENING SURGE ARRESTOR

2 INTRODUCTION TO FDAP
12
www.honeywell.com
Figure 2.2: FDAP GEN3 WITHOUT LIGHTENING SURGE ARRESTOR
Bluetooth Low Energy (BLE) Module
The FDAP Gen3 has an internal BLE module that is used for communicating with the Provisioning Handheld
Android device. The Provisioning Handheld device is used for commissioning the FDAP Gen3, reading, and
setting the various FDAP Gen3 parameters. The BLE module has a range of 10 meter radius.
FDAP Gen3 communication radio
FDAP Gen3 has wireless compliant radios that operate in the 2.4 GHz ISM band. It uses spatial antenna
diversity with sophisticated error correction schemes to improve communication and increase coverage in a
typical industrial complex where multi-path propagation is prevalent.

2 INTRODUCTION TO FDAP
11
Antennas
FDAP Gen3 uses dual antenna diversity to improve communication reliability in severe multi-path environment.
This helps in improving radio coverage and provides robust communication links thereby reducing infrastructure
cost and cost per wireless field device.
FDAP Gen3 has integral omni-directional antennas and it also supports a variety of high- and low-gain omni-
directional antennas to provide flexibility in installation and to maximize performance of the wireless system.
Refer FDAP Gen3 Regulatory Compliance Guide for details about certified antennas and the allowable
maximum RF output power.
FDAP Gen3 has option to integrate lightning suppressors on the antenna ports. Lighting suppressors are
required for all outdoor installations or indoor installations where FDAP Gen3 may be subjected to lightning
surge. Optional remote mounted lightning suppressors are available for use in application where the remote
antenna cable is exposed to lightning surge.
LED indicators
FDAP Gen3 has three LED’s for indicating the status and health of the device. For more information about
LED’s, refer to “Table 3.1: LED indicators”.

2 INTRODUCTION TO FDAP
12
www.honeywell.com
2.4 Physical description of FDAP1/FDAP2
FDAP1/FDAP2 enclosure
The FDAP1/FDAP2 has a rugged die-cast aluminum enclosure for outdoor use. The enclosure and all auxiliary
components are designed to meet IP66 and NEMA Type 4X (FM only) ratings for protection against dust and
water ingress. The enclosure has two water-tight type N bulkhead connectors for antenna spatial diversity in the
FDAP1/FDAP2 radios. The half-inch rigid conduit hub has a gasket to seal out water and dust. A rigid conduit
hub, internal and external ground studs, and a removable cover are provided for field installation. Externally
accessible Infrared (IR) port allows the device to be commissioned in the field. Three status LED’s provide
information about power, device health, and communication. The enclosure may be mounted on a pole or on a
flat surface such as a wall using the available optional mounting brackets. The enclosure measures
approximately 20 cm x 13 cm x 7 cm (L x W x H).
Figure 2: Physical description of FDAP
IR port
The FDAP1/FDAP2 has an externally accessible IR port that is used for communicating with the Provisioning
Handheld device. The Provisioning Handheld device is used for commissioning the FDAP1/FDAP2, reading,
and setting the various FDAP1/FDAP2 parameters. The IR port has a range of 20 cm and a beam width of 20
degrees.
FDAP1/FDAP2 communication radio
FDAP1/FDAP2 has wireless compliant radios that operate in the 2.4 GHz ISM band. It uses spatial antenna
diversity with sophisticated error correction schemes to improve communication and increase coverage in a
typical industrial complex where multi-path propagation is prevalent.

2 INTRODUCTION TO FDAP
13
Antennas
FDAP1/FDAP2 uses dual antenna diversity to improve communication reliability in severe multi-path
environment. This helps in improving radio coverage and provides robust communication links thereby reducing
infrastructure cost and cost per wireless field device.
FDAP1/FDAP2 has integral omni-directional antennas and it also supports a variety of high- and low-gain
directional and omni-directional antennas to provide flexibility in installation and to maximize performance of
the wireless system. Refer FDAP1/FDAP2 Regulatory Compliance Guide for details about certified antennas
and the allowable maximum RF output power,.
FDAP1/FDAP2 has integrated lightning suppressors on the antenna ports. The lightning suppressors are
permanently attached and do not require field maintenance. Lighting suppressors are required for all outdoor
installations or indoor installations where FDAP1/FDAP2 may be subjected to lightning surge. Optional
remote mounted lightning suppressors are available for use in application where the remote antenna cable is
exposed to lightning surge.
LED indicators
FDAP1/FDAP2 has three LED’s for indicating the status and health of the device. For more information about
LED’s, refer to “Table 3.2: LED indicators”.

2 INTRODUCTION TO FDAP
14
www.honeywell.com
2.5 Features of FDAP
The features of FDAP are as follows:
•DC or Universal AC powered: FDAP operates at DC or AC and provides better latency than battery-based
wireless field device mesh network. It enables the use of wireless field devices for applications requiring fast
update rates (less than 10 seconds) and short latency (less than 250 ms) and in areas where Wi-Fi radios are
not allowed.
NOTE
AC is only supported in FDAP1/FDAP2 models.
•Antenna diversity: FDAP uses spatial antenna diversity to improve communication success rates and to
improve coverage in multi-path environments. This is necessary for the majority of industrial application
where there is no direct line of site between field devices. Antenna diversity significantly improves data
availability in such applications.
•Fast Ethernet: FDAP has 10/100 Mbps Fast Ethernet interface and can be integrated into any network that
supports Ethernet communication.
•Field Mesh network: Multiple FDAPs can form a self-forming, self-healing wireless mesh network. This
extends the range and coverage of the wireless sensor network and provides redundant communication paths
for improved data availability. Unlike battery-power field devices, FDAPs are line powered and so can
aggregate data from multiple field devices including other FDAPs without concerns about battery life.
•Reduced cost: FDAP reduces wireless field device cost, infrastructure cost, and cost per wireless I/O. It
reduces the number of wireless routing devices and offers wireless coverage for wireless field devices. It
has lesser installation cost than Access Points for sensor only applications.
•Access points: FDAP acts as a routing access point for wireless field devices and it is designed for sensor-
only network for monitoring application segment.
•IPv6 device: FDAP is an Internet Protocol version 4 (IPv4) device. The IPv4 protocol provides an end-to-
end data transmission across multiple IP networks. FDAP gets the IP address from DHCP Server in Field
Device Network (FDN). You can ping an FDAP from the FDN network. You cannot ping an FDAP from the
Plant Control Network (PCN). You cannot ping an FDAP when used as a Router.
•Backbone router: FDAP is a backbone router in a rugged industrial enclosure that acts as a bridge between
the field device network and wireless backhaul network such as IEEE 802.11 WLAN.

2 INTRODUCTION TO FDAP
15
2.6 FDAP security
OneWireless Network protects plant information and ensures safe operations with industry standard 128-bit
encryption at the mesh, Wi-Fi, and wireless field device level. The FDAP offers a robust embedded wireless
security.
FDAP authentication
FDAP1/ FDAP2 Authentication
In addition to data encryption, Wireless standard requires each FDAP1/ FDAP2 to be authenticated
before joining the network. OneWireless Network relies on a more secured IR authentication key
distribution method as it requires users to be physically next to the FDAP1/ FDAP2 to add it to the
network. The authentication keys are generated and managed by the WDM. A Provisioning Handheld
device is used to upload the authentication keys from the WDM to Provisioning Handheld device and to
download keys to FDAP1/ FDAP2 using IR media. The IR media is used to send an authentication key
from the Provisioning Handheld device to the FDAP1/ FDAP2. Therefore, all Provisioning Handheld
devices and FDAP1/ FDAP2 have IR ports for device commissioning. The keys are encrypted when
distributed over the network. Once a key is deployed to an FDAP1/ FDAP2, it is validated by the WDM
before the FDAP1/ FDAP2 can join the OneWireless Network.
FDAP Gen3 Authentication
In addition to data encryption, Wireless standard requires each FDAP Gen3 to be authenticated before
joining the network. OneWireless Network relies on a more secured Bluetooth Low Energy (BLE)
Module authentication key distribution method as it requires users to be physically next to the FDAP
Gen3 to add it to the network. The BLE module has a range of 10-meter radius. The authentication keys
are generated and managed by the WDM. A Provisioning Handheld device is used to upload the
authentication keys from the WDM to Provisioning Handheld device and to download keys to FDAP
Gen3 using BLE module. The BLE module is used to send an authentication key from the Provisioning
Handheld device to the FDAPGen3. Therefore, all Provisioning Handheld devices and FDAP Gen3
have BLE modules for device commissioning. The keys are encrypted when
distributed over the network. Once a key is deployed to an FDAP Gen3, it is validated by the WDM
before the FDAP Gen3 can join the OneWireless Network.
Key deployment is a one-time activity, that is, the devices can rejoin the network after power down or after any
other service interruptions without re-keying the device. OneWireless supports a key rotation mechanism to
enable a secure network. Once the devices join the network, a master key and a session key is assigned to each
device, and the session key can be rotated on a periodic basis. The key rotation period can be configured from
the OneWireless user interface. For best system performance, it is recommended to set the key rotation period
as infinite.
In addition, from OneWireless R210 release onwards, over the air provisioning is supported for all ISA100
devices. This allows the FDAPs to join the secure OneWireless Network and establish communication with
other devices and the WDM.
Embedded Wireless security
To reduce security threats, wireless devices requires all process data to be 128-bit encrypted. The data is
encrypted at the source and decrypted at the destination to provide end-to-end security for the process data. The
FDAPs self-discover other neighboring wireless routing devices, such as Access Points, and routing wireless
field devices, to form a reliable and secure wireless mesh network.
Wireless routing algorithm enables an FDAP to dynamically identify the best route to send data to and from
wireless field devices. This algorithm enables the field device mesh network to dynamically re-optimize itself
when FDAPs are added to or removed from the network.

16
www.honeywell.com
3 FDAP INSTALLATION
2.7 FDAP compliance information
RED (Radio Equipment Directive)
This device complies with EN 302372 of the R&TTE Directive The device does not cause harmful interference
and accepts any interference received.
WARNING! Changes or modifications made to this equipment not approved by Honeywell invalidate the
compliance to RED.
FCC (Federal Communication Commission) Compliance Statement
FCC information: (FCC ID: S5751307990)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
◼Reorient or relocate the receiving antenna.
◼Increase the separation between the equipment and receiver.
◼Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
◼Consult the dealer or an experienced radio/TV technician for help.
CAUTION! Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
WARNING! In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a
minimum of 7.9inches (20cm) or more from the body of all persons.
WARNING! Since the product uses standard antenna connector, thus only professional installation is permit-
ted.

17
3 FDAP INSTALLATION
Industry Canada (IC) (IC ID: 573W-51307990)
Compliance Statements:
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the
following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interferencethat may cause undesired operation of the
device.
Déclarations de conformité: Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Caution Statements:
• This equipment complies with radio frequency exposure limits set forth by Industry Cananda for an
uncontrolled environment.
•This equipment should be installed and operated with a minimum distance of 20 cm between the device and
the user or bystanders.
Déclarations de mise en garde:
• Cet équipement est conforme aux limites d'exposition aux radiofréquences defines par Indstrie Canada pourun
environment non contrôlé.
• Cet équipement doit être installé et utilisé aven un minimum de 20 cm de distancedispositif et l'utilisateur ou
des tiers.
This radio transmitter [573W-51307990] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for
any type listed are strictly prohibited for use with this device
Sl
No.
Antenna Part
Manufacturer
Antenna Gain
Power Level
Setting (dB)
1
AIR-ANT2450V-N
CISCO
5dBi
20dB
2
AIR-ANT2480V-N
CISCO
8dBi
17dB
3
OD24M-5
Laird Technologies
5dBi
20dB
4
HGV-2409U
L-COM
8dBi
17dB
Le présent émetteur radio [IC: 573W-51307990] a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont trictement interdits pour l'exploitationde l'émetteur

18
www.honeywell.com
3 FDAP INSTALLATION
3FDAP Installation
Related topics
Prerequisites for installation
Inspect FDAP and associated hardware
Identify FDAP site locations
Connect antennas for FDAP Gen3
Connect antennas for FDAP1/FDAP2
Recommendations for remote antenna connections
Ground the FDAP Gen3
Ground the FDAP1/FDAP2
Mount the FDAP Gen3
Mount the FDAP1/FDAP2
Connect power cables and Ethernet cables for FDAP Gen3
Power on and startup for FDAP Gen3
Power on and startup for FDAP1/FDAP2