Hoover ssnb 1700 User manual

®
®
PRINTED IN P.R.C.
48005775/07 1
USER MANUAL
A
B
C
D
G
H
I
J
K
L
M
P
N
O
P
Q
E
F

2 3
6
10 11 12 13
14 15 16 17
18
7 8 9
45
19 20
21
1
2

1
GB
INSTRUCTIONS FOR SAFE USE
This appliance should only be used for domestic cleaning, as
described in this user guide. Please ensure that this guide is fully
understood before operating the appliance.
Do not leave the appliance plugged in. Always switch o and
remove the plug from the socket after use, or before cleaning the
appliance or any maintenance task.
This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Keep the appliance out of reach of children when it is energized or
cooling down.
The appliance is not to be used if it has been dropped, if there are
visible signs of damage or if it is leaking.
If the power cord is damaged stop using the appliance immediately.
To avoid a safety hazard, an authorised Hoover service engineer
must replace the power cord.
This appliance must be earthed.
The appliance shall not be left unattended while it is connected to
the supply mains.
Do not use your appliance out of doors.
Use only attachments, consumables or spares recommended or
supplied by Hoover.
Do not use the appliance to clean or direct steam towards animals,
people or plants.
Liquidorsteammustnotbedirectedtowardsequipmentcontaining
electrical components, such as the interior of ovens.
Use clean water tank to ll the water. Take it out from product and
ll cold tap water then replace it.
The lling aperture must not be opened during use.
Danger of Scalding.
Caution, hot surface. Avoid contact with steam.
Do not stand on or wrap the cord around arms or legs when using
your appliance.
Do not position the appliance above you when cleaning the stairs.
When using the cleaning tools ensure to always steady the
appliance with your other hand. This will ensure that the appliance
does not fall while in use.
Do not handle the plug or appliance with wet hands.
Do not run over the power cord when using your appliance or
remove the plug by pulling on the power cord.
Do not continue to use your appliance if it appears faulty.
Hooverservice:Toensurethecontinuedsafeandecientoperation
of this appliance we recommend that any servicing or repairs are
only carried out by an authorised Hoover service engineer.
Do not immerse the appliance in water or other liquids.
Do not use detergents or liquids other than water inside the
appliance.
For UK and Ireland only: This appliance has a 13 amp mains plug.
If you need to change the fuse in the mains plug, use a 13amp ASTA
(BS1362) fuse.
The Environment
The symbol on this appliance indicates that this appliance may not be treated as
household waste. Instead it must be handed over to the applicable collection point for
the recycling of electrical and electronic equipment. Disposal must be carried out in
accordance with local environmental regulations for waste disposal. For more detailed
information about treatment, recovery and recycling of this appliance, please contact
your local city oce, your household and waste disposal service or the shop where you
purchased the appliance.
This appliance complies with the European Directives 2006/95/EC, 2004/108/EC and
2011/65/EU.
HOOVER Limited, Pentrebach, Merthyr Tydl, Mid Glamorgan, CF48 4TU, UK

2
GETTING TO KNOW YOUR CLEANER
GB
A. Cleaner main body
B. Handle
C. Steam Release Trigger
D. Power Cord
E. Upper cord Clip
F. Lower cord clip
G. On/O Button
H. On Indicator Light (Blue)
I. Steam Ready Indicator Light (Green)
J. Floor Brush
K. Floor Head
L. Floor brush Release Pedal
M. Clean Water Tank
N. Textile Pad
O. Carpet Glider
P. Hard Water Filter
Q. De-scaling Tool
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Insert the handle into the cleaner main body until it locks into position. [2]
2. Assemble the main body of the cleaner to the oor Brush. [3]
3. Assemble the cleaner with oor brush to the oor head. [4]
USING YOUR CLEANER
BEFORE YOU BEGIN CLEANING
1. Remove the clean water tank up and out from the cleaner main body. [5]
2. Twist the cap anti clockwise and remove. [6]
3. Fill the clean water tank with cold tap water. Replace cap. [7] Do not add any chemicals,
detergents or perfumes to the clean water tank.
4. Re-t the clean water tank to the cleaner ensuring the hard water lter is in place.
5. Attach a textile pad to the base of the oor head. [8]
IMPORTANT: Always unplug the cleaner when adding water or changing a textile pad.
NOTE: Wash the textile pad prior to use to remove any lint.
Steam cleaning hard oors
NOTE: Always sweep or vacuum the oor prior to use to remove any loose dirt
or debris.
IMPORTANT: Do not use the cleaner without a textile pad attached to the floor head.
NOTE: Do not use the carpet glider when cleaning hard oors.
1. Plug the steam cleaner into the main power. The blue ON light will illuminate.
2. After a few seconds the green Steam Ready light will illuminate indicating the cleaner is
ready for use.
3. Recline the cleaner by placing a foot on the oor head and lowering the main body
towards the oor. [9]
4. To produce steam press the Steam Trigger Button. [10]
5. Move the cleaner slowly backwards and forwards paying particular attention to high
trac areas. [11]
Steam cleaning hard oor - intensive clean
Use the triangular oor brush on hard oors that require deep cleaning. Please note that there
is no mop to allow the steam to be aimed directly at the surface to clean more intensely. The
area will have to be mopped separately.
NOTE: Always sweep or vacuum the floor prior to use to remove any loose dirt or
debris.
1. Remove the oor brush from the oor head by pressing the release pedal at the rear. Lift
the cleaner with oor brush attached out of the oor head. [12]
2. Plug the steam cleaner into the main power. The blue ON light will illuminate. After a
few seconds the green Steam Ready light will illuminate indicating the cleaner is ready
for use.
3. Recline the cleaner by placing a foot on the oor brush and lowering the main body
towards the oor. [13]
4. To produce steam press the Steam Trigger Button. [10]
5. Move the cleaner slowly backwards and forwards paying particular attention to high
trac areas. [14]
Refreshing carpets
NOTE: Always sweep or vacuum the floor prior to use to remove any loose dirt or
debris.
IMPORTANT: Do not use the cleaner without a textile pad attached to the oor head.
1. Attach the carpet glider to the oor head. [15]
2. Plug the steam cleaner into the main power. The blue ON light will illuminate.
3. After a few seconds the green Steam Ready light will illuminate indicating the cleaner is
ready for use.
4. Recline the cleaner by placing a foot on the oor head and lowering the main body
towards the oor. [9]
5. To produce steam press the Steam Trigger Button. [10]
6. Move the cleaner slowly backwards and forwards paying particular attention to high
trac areas. [11]

3
IMPORTANT: ALWAYS ENSURE THE CLEANER HAS FULLY COOLED DOWN BEFORE
PERFORMING ANY MAINTENANCE TASKS.
Empty the water tank
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2. Remove the clean water tank for the main body of the cleaner. [5]
3. Twist the cap anti-clockwise and remove. [6]
4. Empty any excess water from the tank. [16] Replace the cap and return to the cleaner.
Removing and cleaning the textile pad
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2. If necessary remove the carpet glider, then peel the textile pad from the oor base. [17]
3.
Wash the textile pad in a washing machine with a mild detergent at max temperature 40°C.
IMPORTANT: Do not use bleach or fabric softener when washing the textile pad.
Replacing the hard water lter
The cleaner is tted with a hard water lter. If you live in an area of hard water the lter will
discolour over time. Depending on the water hardness and frequency of use the lter should
be changed every 6 months.
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2. Remove the clean water tank for the main body of the cleaner. [5]
3. Lift the hard water lter out of the cleaner. [18] Replace with new lter.
4. Reassemble the clean water tank to your cleaner.
NOTE: The condition of the lter will aect the cleaner performance.
Cleaning the blockage
1. Turn o the appliance and remove from electrical supply.
Wait for appliance to fully cool down before continuing any maintenance. [19]
2. Ensure the water tank is empty.
3. Detach oor nozzle from cleaner body. [20]
4. Insert supplied de-scaling tool into steam outlet to clear any blockages. [21]
5. Re-assemble oor nozzle to the appliance body.
GB
CLEANER MAINTENANCE
TROUBLESHOOTING
CLEANING FAQS
Should you have a problem with the product, complete this simple user checklist before calling
your local Hoover service.
The steam stick will not switch on.
• Check the unit is plugged in.
• Check the power cord.
When is steamjet ready? In approximately 30 seconds.
Can I use steamjet on all oor surfaces? On all hard oors like marble, ceramic, stone,
linoleum, sealed hardwood oors and parquet.
Does steamjet emit steam automatically? No, to produce steam you should press the steam/
sweep trigger button under the handle.
Can I use it vertically? No, steamjet can be used only on horizontal oor surfaces.
Can I put detergents or other chemicals inside the tank? No, you would damage the
product.
What if in the city where I live the water is very hard? You can use ltered water or you
will have to change the lter cassette more often. If you nd very weak steam, check steam
orice,you can descale it by inserting small tools into steam orice if necessary.
When is it time to change the lter cassette? How do you notice it? It depends on the water
hardness. Normally 6 months. You will notice that the colour of yellow resin inside the lter
cassette becomes a bit dull.
How long will one tank of water last before needing to be relled? Approximately 20
minutes if you press continuously the trigger.
Is the mop washable? Yes, it can be washed by hand or in the washing machine with a mild
detergent at max temperature 40°C. Do not use bleach or fabric softener.
How often should I replace the mop? It depends on dierent factors above all how hard the
oor is. The best way to understand when to change the mop is when the mop is still dirty after
having washed it or if you notice that it doesn’t perform like before.
The steam stick is not producing steam.
• There may be no water in the clean water tank.
• The tank may not be fitted correctly.
The textile pad won’t pick up dirt.
• The cleaning pad may already be saturated with dirt and needs to be washed. Refer to
the Maintenance section.

4
GB
IMPORTANT INFORMATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local Hoover
dealer or direct from Hoover. When ordering parts always quote your model number.
Consumables
Textile Pad: 35601330
Filter: 35601335
Hoover Customer Helpline Service
Should any faults occur with your cleaner during the rst 12 months, contact the Hoover
Customer Helpline on the number below.
Tel: [phone]
Email: [e-mail]
Quality
Hoover’s factories have been independently assessed for quality. Our products are made using
a quality system which meets the requirements of ISO 9001.
Your Guarantee
The guarantee conditions for this appliance are as dened by our representative in the country
in which it is sold. Details regarding these conditions can be obtained from the dealer from
whom the appliance was purchased. The bill of sale or receipt must be produced when making
any claim under the terms of this guarantee.
Subject to change without notice.