Horizon Fitness ELITE R7 User manual

ASSEMBLY GUIDE
GUIDE D’ASSEMBLAGE
GUÍA DE ENSAMBLAJE
ELITE R7
U7

2
3 ENGLISH
20 FRANÇAIS
38 ESPAÑOL

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the exercise bike could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the exercise bike, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your exercise bike’s serial number and enter it in the space
provided below. The serial number will be located on a white sticker with a bar code.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
MODEL NAME: HORIZON EXERCISE BIKE
WARNING
16
13
B
J
SERIAL NUMBER:
SERIAL NUMBER LOCATION

4
R7
CONSOLE MAST HANDLEBARS
CONSOLE
WATER BOTTLE HOLDER
CONSOLE MAST
CONSOLE MAST GROMMET
POWER CORD SOCKET
PEDALS
FRONT STABILIZER TUBE
CRANK
FRONT SHROUD
PULSE GRIP HANDLEBARS
SEAT BASE
MESH SEAT BACK
SEAT SLIDE
REAR STABILIZER TUBE
SEAT POSITION ADJUSTMENT LEVER

5
U7
CONSOLE
CONSOLE MAST
SEAT HEIGHT ADJUSTMENT KNOB
CONSOLE MAST GROMMET
SHROUD
FRONT STABILIZER TUBE
PEDALS
PULSE GRIP HANDLEBARS
WATER BOTTLE HOLDER
SEAT
SEAT POSITION ADJUSTMENT KNOB
SEAT POST TUBE
POWER CORD SOCKET
(BOTTOM RIGHT SIDE)
CRANK
REAR STABILIZER TUBE

6
TOOLS INCLUDED:
F13/15mm Flat Wrench
FPhillips Screwdriver/Allen Wrench
PARTS INCLUDED:
F1 Bike Frame
F1 Console
F1 Console Mast
F1 Console Mast Grommet
F1 Front Stabilizer Tube
F1 Rear Stabilizer Tube
F1 Seat
F1 Mesh Seat Back (R7 only)
F1 Seat Back Bracket (R7 only)
F1 Seat Post Tube (U7 only)
F1 Seat Post Bracket (U7 only)
F1 Handlebar Bracket Cover (U7 only)
F1 Pulse Grip Handlebars
F2 Pedals with Straps
F1 Water Bottle Holder
F1 Audio Adapter Cable
F1 Power Cord
F1 Hardware Kit
UNPACKING
Unpack the product where you will be using it. Place the bike carton
on a level flat surface. It is recommended that you place a protective
covering on your floor. Never open box when it is on its side.
If you have questions or if there are any missing parts, contact
Customer Tech Support. Contact information is located on the
back panel of this manual.
NEED HELP?
PRE ASSEMBLY
• During each assembly step, ensure that ALL nuts and bolts
are in place and partially threaded. It is recommended you
complete the full assembly of your unit before completely
tightening any ONE bolt.
• Several parts have been pre-lubricated to aid in assembly and
usage. Please do not wipe this off. If you have difficulty, a light
application of lithium bike grease is recommended.
IMPORTANT NOTES

7
ASSEMBLY
R7
page 8
U7
page 14

8
R7 ASSEMBLY STEP 1
A Open HARDWARE FOR STEP 1.
B Attach the FRONT STABILIZER TUBE (1) to the
BIKE FRAME (2) using 2 BOLTS (A), 2 FLAT
WASHERS (B), 2 SPRING WASHERS (C) and
2 NUTS (D).
C Attach the REAR STABILIZER TUBE (3) to the
BIKE FRAME (2) using 2 BOLTS (A), 2 FLAT
WASHERS (B), 2 SPRING WASHERS (C) and
2 NUTS (D).
2
1
D
C
B
3
A
R7
HARDWARE FOR STEP 1
PART TYPE QTY
ABOLT 4
BFLAT WASHER 4
CSPRING WASHER 4
DNUT 4

9
R7 ASSEMBLY STEP 2
A Open HARDWARE FOR STEP 2.
B Slide CONSOLE MAST GROMMET (4) from the
bottom up the CONSOLE MAST (5).
C Carefully pull the HEART RATE CABLE (20)
through the CONSOLE MAST (5) using the twist
tie located inside the CONSOLE MAST (5).
D Attach CONSOLE CABLES (6) and carefully tuck
all cables into BIKE FRAME (1). Slide CONSOLE
MAST (5) into BIKE FRAME (1).
E Attach the CONSOLE MAST (5) using 4 BOLTS
(E), 4 SPRING WASHERS (C) and 4 FLAT
WASHERS (B) from the rear.
F Slide CONSOLE MAST GROMMET (4) down over
BIKE FRAME (1).
20
1
5
4
6
B
C
E
20
R7
NOTE: Be careful not to pinch any wires while attaching the console mast.
HARDWARE FOR STEP 2
PART TYPE QTY
EBOLT 4
BFLAT WASHER 4
CSPRING WASHER 4

10
R7 ASSEMBLY STEP 3
* NOTE: There is no hardware for this step.
A Attach PEDAL STRAPS (7) to PEDALS (8).
B Attach the RIGHT PEDAL to the RIGHT CRANK
ARM, tightening it CLOCKWISE with the provided
13mm/15mm flat wrench.
C Attach the LEFT PEDAL (8) onto the LEFT
CRANK ARM (9), tightening it COUNTER-
CLOCKWISE with the provided 13mm/15mm flat
wrench. (NOTE: The left crank arm is reversed
threaded so it is very important that it is tightened
counter-clockwise. Tightening it the opposite way
can damage the pedal or the crank arm or both.)
D Connect the CONSOLE CABLES (6) and carefully
tuck them into the CONSOLE MAST (5).
E Attach the CONSOLE (10) to the CONSOLE
MAST (5) using the 4 PRE-ATTACHED SCREWS
(11) (The screws will have to be removed from the
console first).
10
7
8
11
5
9
8
6
R7
NOTE: Be careful not to pinch any wires while attaching the console.