Horizon Fitness COMFORT 2.0 User manual

COMFORT 2.0 COMFORT 4.0 COMFORT 8.1 COMFORT R8.0
Read the BIKE GUIDE before using this OWNER’S MANUAL.
Lesen Sie das ERGOMETER-HANDBUCH, bevor Sie dieses BENUTZERHANDBUCH verwenden.
Lees de FIETSGIDS voor u deze GEBRUIKERSHANDLEIDING gebruikt.
Lisez le GUIDE DU VÉLO avant d’utiliser ce MANUEL DU PROPRIÉTAIRE.
OWNER’S MANUAL
BENUTZERHANDBUCH
GEBRUIKERSHANDLEIDING
MANUEL DU PROPRIÉTAIRE
Art.Nr. 2981000

3 ENGLISH
61 DEUTSCH
119 NEDERLANDS
177 FRANÇAIS

3
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
When using an exercise product, basic precautions should always be followed, including the following: Read all instructions
before using this exercise bike. It is the responsibility of the owner to ensure that all users of this exercise bike are adequately
informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact your local
dealer.

4
READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS
EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY
INSTRUCTIONS.
• CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult
your physician before continuing.
• Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been
recommended by the manufacturer.
• Never operate the exercise bike if it is not working properly, or if it has been damaged. Contact the authorized dealers for
examination and repair.
• Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.
• Do not wear any clothing that might catch on any moving parts of this exercise bike.
• Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.
• Do not dismount the exercise bike until the pedals are at a complete STOP.
• Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.
• Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other
potentially moving part of the exercise bike.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• Close supervision is necessary when used near children, invalids or disabled people.
• When the exercise bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.
• Ensure that adjustment levers (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of
motion during exercise.
• This application is for home and indoor use only.
• This application with speed independent system.
• If any of the adjustment devices are left projecting, they could interfere with the user’s movement.
• WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in serious injury or death. If you
feel faint stop exercising immediately.
WARNING

5
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the exercise bike could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the exercise bike, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your exercise bike’s serial number located on
the front stabilizer tube and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
WARNING
SERIAL NUMBER LOCATION
SERIAL NUMBER:
MODEL NAME: HORIZON

6
Comfort
R8.0
HANDLEBARS
SEAT BACK
SEAT BASE
CRANK
REAR STABILIZER PEDALS
CONSOLE
CONSOLE MAST
PULSE GRIP HANDLEBARS
WATER BOTTLE HOLDER
SEAT POSITION
ADJUSTMENT LEVER
CONSOLE MAST GROMMET
MAIN FRAME
POWER CORD SOCKET
TRANSPORT WHEELS
FRONT STABILIZER TUBE

7
TOOLS REQUIRED:
F13/15mm Flat Wrench/Screwdriver
F5mm L-Wrench
F6mm L-Wrench
PARTS INCLUDED:
F1 Main Frame
F1 Console
F1 Console Mast
F1 Console Mast Grommet
F1 Water Bottle Holder
F1 Front Stabilizer Tube
F1 Rear Stabilizer Tube
F1 Seat Base
F1 Seat Back
F1 Seat Frame
F1 Seat Frame Cover
F1 Pulse Grip Handlebars
F2 Pedals with Straps
F1 Audio Adapter Cable
F1 Power Cord
F1 Hardware Kit
UNPACKING
Unpack the product where you will be using it. Place the bike carton on a level
flat surface. It is recommended that you place a protective covering on your
floor. Never open box when it is on its side.
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded. It is recommended you complete the full assembly of your
unit before completely tightening any ONE bolt.
Several parts have been pre-lubricated to aid in assembly and usage. Please
do not wipe this off. If you have difficulty, a light application of lithium bike
grease is recommended.
If you have questions or if there are any missing parts, contact your local
dealer. Contact information may be located on the back panel of your
manual or on the warranty card.
NEED HELP?
RECUMBENT BIKE PRE ASSEMBLY
Comfort
R8.0

8
RECUMBENT BIKE ASSEMBLY STEP 1
MAIN FRAME
NUT (D)
FLAT WASHER (B)
SPRING
WASHER (C)
BOLT (A)
REAR STABILIZER
FRONT STABILIZER
A Open HARDWARE FOR STEP 1.
B Attach the REAR STABILIZER to the MAIN
FRAME using 2 BOLTS (A), 2 FLAT WASHERS
(B), 2 SPRING WASHERS (C) and 2 NUTS (D).
C Attach the FRONT STABILIZER to the MAIN
FRAME using 2 BOLTS (A), 2 FLAT WASHERS
(B), 2 SPRING WASHERS (C) and 2 NUTS (D).
Note: Lifting up the machine will help your assembly.
First put in place the stabilizer and then insert the bolts
will also make your assembly easier.
Comfort
R8.0
HARDWARE FOR STEP 1
BOLT (A)
M8 X 56 MM
QTY: 4
FLAT WASHER (B)
Φ9X Φ18 X 2.0T MM
QTY: 4
SPRING WASHER (C)
M8 X 2.0T MM
QTY: 4
NUT (D)
M8
QTY: 4

9
RECUMBENT BIKE ASSEMBLY STEP 2
A Open HARDWARE FOR STEP 2.
B Slide WATER BOTTLE HOLDER up CONSOLE
MAST and align screw holes in WATER BOTTLE
HOLDER with holes in CONSOLE MAST.
C Attach the WATER BOTTLE HOLDER using 2
SCREWS (E).
CONSOLE MAST
WATER BOTTLE HOLDER
SCREW (E)
Comfort
R8.0
HARDWARE FOR STEP 2
SCREW (E)
M4 X 12 MM
QTY: 2

10
RECUMBENT BIKE ASSEMBLY STEP 3
A Open HARDWARE FOR STEP 3.
B Slide CONSOLE MAST GROMMET from the
bottom up the CONSOLE MAST .
C Attach CONSOLE CABLES and carefully tuck all
cables into MAIN FRAME. Slide CONSOLE MAST
into MAIN FRAME.
D Attach the CONSOLE MAST using 2 BOLTS
(G) from the sides and 4 BOLTS (F) and 4 FLAT
WASHERS (B) from the front.
E Slide CONSOLE MAST GROMMET down over
MAIN FRAME.
BOLT (F)
BOLT (G)
FLAT WASHER (B)
CONSOLE CABLES
MAIN FRAME
CONSOLE MAST GROMMET
CONSOLE MAST
Comfort
R8.0
HARDWARE FOR STEP 3
BOLT (F)
M8 X 60 MM
QTY: 4
BOLT (G)
M8 X 18 MM
QTY: 2
FLAT WASHER (B)
Φ9 X Φ18 X 2.0T MM
QTY: 4