Horizon Hobby Vibe 500e User manual

ASSEMBLY INSTRUCTIONS
Vibe 500e Specications
Overall Length........................33.25 in (844.55mm)
Height........................................11.75 in (298.45mm)
Main Rotor Diameter ...........37.75 in (958.85mm)
Tail Rotor Diameter..........................7.3 in (185mm)
Main Gear Ratio ................................7.08:1 or 6.54:1
Tail Gear Ratio........................................................ 4.5:1
Weight (without battery) ............... 3.9 lb (1800 g)
Control System............................................120 CCPM

2
TABLE OF CONTENTS
Introduction .........................................................................3
Key Features .........................................................................3
Preassembly Warning .......................................................4
Recommended Radio System........................................4
Items Required to Complete Assembly......................5
1-1A Attaching the Servo Adapters............................6
1-1B Assembling the Guide Roller..............................6
1-2 Attaching the Guide Roller..................................7
1-3 Attaching the Bearing Case and
Frame Support.........................................................7
1-4 Attaching the Body Catch....................................8
1-5 Attaching the Frame Bridge................................8
1-6 Attaching the Radius Support ...........................9
1-7 Attaching the Battery Mount .............................9
1-8 Attaching the Landing Gear ............................10
2-1 Attaching the Tail Pulley Case .........................10
2-2 Attaching the Tail Output Shaft......................11
2-3 Assembling the Tail Pitch Control Lever......11
2-4 Attaching the Tail Pitch Control Lever 1 ......12
2-5 Attaching the Tail Pitch Control Lever 2 ......12
2-6 Attaching the Tail Rotor Grip ...........................13
2-7 Attaching the Tail Rotor Blade.........................13
2-8 Attaching the Horizontal Stabilizer and
Vertical Fin..............................................................14
2-9 Installing the Tail Boom ..................................... 14
3-1 Attaching the Gyro Mount ...............................15
3-2 Assembling the Boom Supports ....................15
3-3 Attaching the Boom Supports........................16
3-4 Assembling the Main Drive Gear ...................16
3-5 Attaching the Main Drive Gear and
Front Pulley ............................................................17
4-1 Assembling the Swashplate and
Washout Assembly..............................................18
4-2 Attaching the Swashplate and
Washout Assembly..............................................18
4-3 Assembling the Main Blade
Holder and Rotor Hub Part 1 ...........................19
4-4 Assembling the Main Blade Holder and
Rotor Hub Part 2...................................................19
4-5 Attaching the Seesaw ........................................20
4-6 Attaching the Seesaw Arm...............................20
4-7 Attaching the Main Rotor Head......................21
4-8 Attaching the Stabilizer Arm ...........................21
4-9 Attaching the Paddle Decals ...........................22
4-10 Attaching the Paddle..........................................22
4-11 Installing Main Rotor Head Linkages............ 23
5-1 Assembling the Motor and Motor Mount...23
5-2 Attaching the Motor........................................... 24
5-3A Installing Mini Servos Part 1.............................24
5-3B Installing Mini Servos Part 2.............................25
5-4A Installing Standard Servos Part 1 ...................25
5-4B Installing Standard Servos Part 2 ...................26
5-5 Preparing the Servo Arms.................................26
Radio System Preparation............................................ 27
Understanding CCPM Control Systems................... 28
Important CCPM Programming
Do’s and Don’ts.....................................................30
CCPM Software Initial Adjustments..........................31
JR 12X Programming......................................................32
JR X9303 2.4 and XP9303: Programming................36
JR 7202 and Spektrum DX7se and DX7:
Programming ........................................................40
5-6 Installing the Servo Arms..................................44
5-7 Installing Swash Servo Linkages ....................45
5-8 Assembling the Tail Control Rod .................... 46
5-9 Attaching the Tail Control Rod........................46
6-1 Installing the Speed Controller.......................47
6-2 Installing the Receiver and Gyro .................... 47
6-3 Fixing the Wiring.................................................. 48
6-4 Installing the Battery ..........................................48
6-5 Installing the Body ..............................................49
Basic Adjustment After Assembly .............................50
6-6 Balancing the Main Rotor Blades ................... 51
6-7 Attaching the Main Rotor Blades...................51
Leveling the Swashplate...............................................52
Pitch-to-Aileron Mixing Adjustment ........................53
Pitch-to-Elevator Mixing ............................................... 54
Tail Servo Adjustment....................................................55
Final Servo Adjustment and Radio Setup...............56
Pitch Range and Curve Settings................................. 57
Pitch Adjustment Linkages..........................................58
Conrmation of Proper Blade Direction..................59
Final Preight Check....................................................... 59
Blade Tracking Adjustment..........................................60
General Maintenance.....................................................61
Repair of Assemblies......................................................62
Repair of Assemblies......................................................63
Replacement Parts Listing............................................64

3
INTRODUCTION
KEY FEATURES
To say electric helis are everywhere these days is a bit of an understatement. Electric helicopter performance and
popularity is on a level now that is unprecedented in the history of RC. And with the demand for more power
and potential comes the demand for a heli platform that can handle it.
Enter the Vibe 500e. JR’s latest foray into electric helicopter design has the benet of drawing on years of glow
heli development, producing a platform built from the ground up to dominate. The design is all new, and was
conceived with one goal in mind—being the smoothest, most precise electric helicopter available. Features like
the belt-driven tail, aluminum head and tail assemblies plus more, make precision and smoothness a possible
reality. The result is a connection between you and your heli that feels like nothing you’ve ever own before.
• 120CCPM
• Belt-driventail
• Fullaluminumheadandtailassemblies
• Designedfor6SLi-Popower(2200or2600mAhThunderPowerorsimilar)
• DesignedforE-itePower251000Kvhighpowerhelimotorsystemforaggressive3Dperformance
• UsesE-ite60-AmpProESC
• Requires425–430mmmainblades
• Constantdriventailrotor

4
PREASSEMBLY WARNING
RECOMMENDED RADIO SYSTEM
When rst opening your helicopter, you will notice that all of the parts are packaged and numbered to
coordinate with the assembly step numbers of this instruction manual. All small hardware (nuts, bolts, washers,
etc.) for each step is separated and packaged separately within the main parts bags. When beginning a section,
you will need to open only the bag with the corresponding number to the section you are going to start. It is
suggested that you place all of the hardware in an open container (e.g., coee can) during assembly so as not
to lose any of the small parts. It may also be helpful to familiarize yourself with the various sizes of screws, bolts,
nuts, etc., as illustrated in the appropriate assembly section before you begin assembly. At the end of each
assembly, in most cases, there should be no parts remaining.
NOTE: Your kit also includes JR® red and green threadlock. Unlike conventional U.S.-made
threadlock, JR red is the U.S. equivalent of blue. JR green is the equivalent of U.S. red.
Great care has been taken in lling the bags with the correct quantity of parts and hardware for each section.
However, occasionally mistakes do happen. In the event that you nd a parts shortage or are in need of
technical assistance, please contact your local JR Heli Division parts dealer or contact the Horizon Service Center
directly.
JR 12X 2.4
(JRP1200)
JR X9303 2.4
(JRP2925)
Spektrum DX7se
(SPM2731)
CCPM-Ready JR Radio Systems
Most current JR and Spektrum heli radio
systems (12X, XP9303, X9303 2.4, DX7se,
DX7 and DX6i) are equipped with 120° CCPM
electronics for use with JR CCPM machines.
Radios you may be ying now, like the X347,
X388S, XP783 and XP8103* have 120° CCPM
capability built in but require activation by
the Horizon Service Department. For details,
please call [phone].
*Please note that many XP8103 systems
have the CCPM function already activated.
Please check with the Horizon Service
Center for details.
Spektrum is used with permission of
Bachmann Industries, Inc.

5
ITEMS REQUIRED TO COMPLETE ASSEMBLY
G770 3D Gyro (JRPG7703D)
E-ite Power 25 Heli BL
Outrunner Motor,1000KV
(EFLM4025H)
Oil Touch Pen
(JRP961296)
2200mAh–2600mAh
(6S Battery) (THP27006SP30)
PAAPT39
30-Minute Z-Poxy
3500G Gyro Servo (JRPG3500G)
PAAPT02
Zap-A-Gap CA+
Rubbing Alcohol
Nylon Wire Ties (ASC7709)
E-ite 60-AMP PRO SB
Brushless ESC (EFLA1060)
Double-Sided Servo Tape
(BRP7541)
DS3517 High-Speed Mini Servo
(x3)
Grease
Spektrum AR6200, AR7000 or JR
R921 Receiver
(SPMAR6200)
Pitch Gauge w/Case
JRP960326

6
11A ATTACHING THE SERVO ADAPTERS
11B ASSEMBLING THE GUIDE ROLLER
SocketHeadBolt,M3×10
………×2
SocketHeadBolt,M2.6×8
………×16
NylonLockNut,M2.6
………………×16
Red
(×2)
Socket Head Bolt, M2.6 x 8 (16 Pcs)
Socket Head Bolt, M3 x 10 (2 Pcs)
Nylon Lock Nut, M2.6 (16 Pcs)
Guide Roller Block (2 Pcs)
Guide Roller (2 Pcs)
Top
Bottom
Guide Roller Spacer (2 Pcs)
Main Frame L
Main Frame R
Mini Servo
38.5mm
Servo Adapters (4 Pcs)
Prepare 2 sets of
the Guide Roller
assembly.
Note the proper
direction of the
Guide Roller.
Install the servo
adapter in the direction
shown noting the
direction of the hole in
the adapter.
Note: Either Mini Servos
such as the DS3517 or
Standard Servos such as the
DS821 can be installed. If
using Mini Servos, install the
servo adapters
as shown. If
using Standard
Servos, skip
ahead to step
1-1B.
The at edge of the
adapter should be
installed toward the
frame.

7
12 ATTACHING THE GUIDE ROLLER
13 ATTACHING THE BEARING CASE AND FRAME SUPPORT
SocketHeadBolt,M2.6×6
……………×4
SocketHeadBolt,M2.6×8
……………×6
SocketHeadBolt,M2.6×10
……………×8
Red(×8)
Red (×6)
Red (×4)
Socket Head Bolt, M2.6 x 6 (4 Pcs)
Socket Head Bolt, M2.6 x 8 (6 Pcs)
Socket Head Bolt,
M2.6 x 10 (8 Pcs)
Guide Roller Assembly (2 Pcs)
SG Twist Support, Upper (2 Pcs)
Absorber Post(2 Pcs)
Absorber Cap (2 Pcs)
3mm
HG Bearing Case (2 Pcs)
HG Cross Member (2 Pcs)
Frame Support Plate, Lower (2 Pcs)
Main Frame R
Main Frame L
Prepare 2 sets of
the Absorber Post
assembly.

8
14 ATTACHING THE BODY CATCH
15 ATTACHING THE FRAME BRIDGE
SocketHeadBolt,M2.6×8
…………×3
SocketHeadBolt,M2.6×8
……………×4
SocketHeadBolt,M2.6×6
……………×2
……………×2
Self-TappingScrew,M2.6×8
……………×2
Self-TappingScrew,M2.6×10
Red (×2)
Red
Temp. (×4)
Red(×2)
Socket Head Bolt, M2.6 x 8 (3 Pcs)
Socket Head Bolt, M2.6 x 8 (4 Pcs)
Socket Head Bolt,
M2.6 x 6 (2 Pcs)
Frame Stando
Block
Self-Tapping Screw, M2.6 x 10 (2 Pcs)
Self-Tapping Screw,
M2.6 x 8 (2 Pcs)
Frame Bridge R/L
Brace Mount(2Pcs)
Front
Body Catch 23mm (2 Pcs)
SG Body Mount Plate (Rear) (2 Pcs)
Body Catch 4mm
Body Catch Mount
Do not fully
tighten M2.6 x 6
screws until the
landing gear is
installed later.

9
16 ATTACHING THE RADIUS SUPPORT
17 ATTACHING THE BATTERY MOUNT
Soft(×6)
Soft(×6 )
Red(×4)
SocketHeadBolt,M2.6×8
……………×4
……………×4
Self-TappingScrew,M2.6×10
……………×6
FlatHeadScrew,M2.6×5
SocketHeadBolt,M2.6×6
…………×6
Socket Head Bolt, M2.6 x 8 (4 Pcs)
Socket Head Bolt, M2.6 x 6 (6 Pcs)
Self-Tapping Screw, M2.6 x 10 (4 Pcs)
Flat Head Screw, M2.6 x 5 (6 Pcs)
Brace Mount (3 Pcs)
Carbon Battery Mount
HG Cross Member 25mm (2 Pcs)
Radius Support
Hook and Loop Strap M (2 Pcs)

10
18 ATTACHING THE LANDING GEAR
21 ATTACHING THE TAIL PULLEY CASE
SocketHeadBolt,M2.6×12
………×4
FlatWasher,M2.6
…………………×4
Soft(×4 )
SocketHeadBolt,M2×5
……………×2
SocketHeadBolt,M2.6×6
……………×1
Red
(×2)
Red
0.5mm
Socket Head Bolt, M2.6 x 12 (4 Pcs)
Socket Head Bolt,
M2.6 x 6
Socket Head Bolt, M2 x 5 (2 Pcs)
Tail Pitch Control Base
Clear Tape
Tail Pulley Case
Tail Pulley
Tail Drive Belt
Tail Boom L470
Flat Washer, M2.6 (4 Pcs)
Landing Gear
Note: After the
landing gear is
installed, fully
tighten the bolts
left loose from
Step 1-5.
Note: To easily pull the tail drive
belt through the tail boom, wrap a
small piece of tape around the belt
using great care to not pinch the
belt at the bend and weakening
the belt. Caution: If the belt is bent
or kinked during assembly it will
damage the belt and cause a failure
resulting in loss of tail control.
Note: Tighten the M2.6 x 6 socket
head bolt carefully when tightening
on the Tail Boom, the Tail Boom will
be damaged if overtightened. There
should be a gap remaining in the
clamp when fully tightened.
Note: The notched end of the tail boom
installs into the Tail Pulley Case. Insert the
Tail Boom as deeply as possible.

11
22 ATTACHING THE TAIL OUTPUT SHAFT
23 ASSEMBLING THE TAIL PITCH CONTROL LEVER
Red
(×2)
Red
(×2)
……………×2
Setscrew,M3×4
SocketHeadBolt,M2×6
…………×2
Polysliderwasher4.1×6.5×0.13
………………×2
SocketHeadBolt,M2×6
…………×2
FlatHeadScrew,M2×8
…………×1
Nut,M2
………………×1
ERetainingRing,M1.5
………×5（1spare）
Red
Red (×2)
Red
Tail Case Cross Member
Joint Ball
Nut, M2
Tail Output Shaft
Tail Pulley Side
Setscrew, M3 x 4 (2 Pcs)
Socket Head Screw, M2 x 6 (2 Pcs)
Flat Head Screw, M2 x 8
Tail Slide Ring
Tail PC Plate
Tail PC Link (2 Pcs)
Tail Pitch Control Arm
HG Tail PC Link Pin(2 Pcs)
Tail Pitch Control Lever
E Retaining Ring, M1.5 (4 Pcs)
Tail Slide Ring Sleeve
Socket Head Bolt, M2 x 6 (2 Pcs)
If the Tail Pulley has too much play (to
the left and right) install the included
Polyslider washers to adjust. Install
the washers as necessary to eliminate
any free play in the tail pulley.
Note: Be certain the
e-clips are fully installed
in the groove in the pin.
Note: Be sure to note the
proper tightening direction
for the Tail Slide Ring Sleeve,
it is reverse threaded.
Note: Be sure to install
the Tail PC Link in the
correct direction. The side
with the circular marks
should be in the direction
of the arrow.

12
24 ATTACHING THE TAIL PITCH CONTROL LEVER 1
25 ATTACHING THE TAIL PITCH CONTROL LEVER 2
SocketHeadBolt,M2.6×6
……………×2
Red (×2)
Red (×2)
Degrease
Red (×2)
TailPCSlideBolt
…………×2
O-Ring3.8×7.6×1.9(90°)
……………×1
Socket Head Bolt, M2.6 x 6 (2 Pcs)
O-ring 3.8 x 7.6 x 1.9 (90°)
Tail PC Slide Bolt (2 Pcs)
Tail Pitch Control
Bearing Collar(2 Pcs)
Apply a thin and
even layer of red
threadlock to adhere
Tighten the Tail PC
Slide Bolts, tting
them in the groove
in the tail slide ring.

13
26 ATTACHING THE TAIL ROTOR GRIP
27 ATTACHING THE TAIL ROTOR BLADE
FlatHeadScrew,M2×7
……………×2
SocketHeadBolt,M3×10
………×2
Washer,03×4.5×0.4
…………………×2
………………×1
Setscrew,M3×4
O-Ring3.5×5.5×1
…………………×2
Red(×2)
Red
SocketHeadBolt,M2.6×12
………×2
NylonLockNut,M2.6
…………………×2
Red
(×2)
O-ring 3.5 x 5.5 x 1 (2 Pcs)
Washer, 3 x 4.5 x .04 (2 Pcs)
Socket Head Bolt, M3 x 10 (2 Pcs)
Flat Head Screw, M2 x 7 (2 Pcs)
Nylon Lock Nut, M2.6 (2 Pcs)
Long Tail Rotor Blade (2 Pcs)
Socket Head Bolt, M2.6 x 12 (2 Pcs)
Joint Ball (2 Pcs)
Tail Rotor Grip (2 Pcs)
Setscrew, M3 x 4
Tail Center Hub
Note: Clamp the Tail Rotor Blades
uniformly to an extent that the tail
blade will move back and forth
when a slight force is applied to
them by hand.

14
28 ATTACHING THE HORIZONTAL STABILIZER AND VERTICAL FIN
29 INSTALLING THE TAIL BOOM
Temp. (×2)
Red (×6)
FlatWasher,M2.6
…………………×2
SocketHeadBolt,M2.6×4
……………×2
90°
CA
Red (×2)
SocketHeadBolt,M2.6×6
……………×6
SocketHeadBolt,M2.6×20
…×2
Socket Head Bolt,
M2.6 x 4 (2 Pcs)
Flat Washer, M2.6 (2 Pcs)
HG Tail Boom Holder (2 Pcs)
Tail Support Clamp
Horizontal Stabilizer
Vertical Fin
Socket Head Bolt, M2.6 x 20 (2 Pcs)
Socket Head Bolt, M2.6 x 6 (6 Pcs)
Note: Do not fully
tighten the M2.6x20
socket head bolts until
the belt tension is set in
a later step.
Note: Insert the tail boom as far
forward as it will go into the tail
boom holders; belt tension will be set
later in the assembly.
Note: Pay close attention to the direction of rotation of the belt. With the belt
installed as shown, sight down the tube to ensure that the belt is not twisted down
the length of the boom, then rotate the belt 90 degrees in the direction of the arrow to
ensure the tail blades rotate the proper direction and the belt is not twisted or kinked.
The tail blade rotation direction will be veried later in step 3-5.
Caution: If the belt is twisted or kinked it will cause premature wear and failure of the
belt which will cause loss of tail control.

15
31 ATTACHING THE GYRO MOUNT
32 ASSEMBLING THE BOOM SUPPORTS
EPOXYA+B（×）4
Self-TappingScrew,2.6×8
…………×4
Self-Tapping Screw, M2.6 x 8 (4 Pcs)
Boom Support End (4 Pcs)
Carbon Tail Boom Support L275(2 Pcs)
Gyro Mount
Note: Prior to assembly, lightly sand
the ends of the carbon boom supports
to ensure a good bond with the boom
support ends.
Note: Adhere the Boom Support
ends carefully in alignment with
each other as shown.
Assemble 2 Boom
Supports

16
33 ATTACHING THE BOOM SUPPORTS
34 ASSEMBLING THE MAIN DRIVE GEAR
Red (×2)
Temp.
SocketHeadBolt,M2.6×6
…………×4
FlatWasher,M3
……………………………×4
NylonLockNut,M3
……………………………×1
SocketHeadBolt,M3×35
…×1
SocketHeadBolt,M3×10
……………………×2
Red (×4)
Socket Head Bolt,
M3 x 35
Socket Head Bolt, M3 x 10 (2 Pcs)
Socket Head Bolt, M2.6 x 6 (4 Pcs)
Cross Member 25mm
(Black)
Nylon Lock Nut, M3
Flat Washer, M3 (4 Pcs)
Autorotation Sleeve
T85 Main Drive Gear
Autorotation Unit
Top
Bottom
Note: Do not fully tighten M3 x 35
socket head bolt at this time. This
bolt will be tightened in step 3-5
when the belt tension has been set.
Note: Insert the
Autorotation Sleeve into
the Autorotation Unit.
Note: Tighten the bolts
for the main gear equally
to prevent warping.

17
35 ATTACHING THE MAIN DRIVE GEAR  FRONT PULLEY
Soft (×2)
SocketHeadBolt,M2.6×15
………×2
NylonLockNut,M2.6
…………………×2
…………………×2
Setscrew,M3×3
MainShaftSpacer
…………………×1
Main Shaft
Main Shaft Collar
Front Pulley
Main Drive Gear
Assembly
Autorotation Collar
Nylon Lock Nut, M2.6 (2 Pcs)
Main Shaft Spacer
Note: After installing the Front
Pulley and Auto Rotation Assembly,
push down on the Main Shaft, and
pull up on the Main Shaft Collar
until it is against the top Main
Shaft Bearing Block. Tighten the
M3 x 3 Setscrews in the Collar
while holding the Main Shaft Collar
against the Bearing Block and the
Main Shaft pressed down against
the lower Main Shaft Bearing Block.
Note: The proper
direction to install the
Auto Rotation Collar is
as shown.
Note: If the Tail Boom is stuck and
cannot easily be moved, loosen the Gyro
Mount attachment screws.
Check that the Tail Drive Belt
direction rotation is correct as shown
and there are no twists in the belt.
Ensure the Tail Blades rotate in the
proper direction prior to ight.
Note: After the direction of the Tail Drive Belt has been conrmed, set the belt
tension. The belt tension should be set by pulling out on the Tail Boom so that
the belt will remain in contact with the Guide Roller when pressed with a nger
between the Front Pulley and Guide Roller. When the belt tension is set properly,
tighten the bolts left loose previously in step 3-3.
Note: After installing the Main Shaft
through the bottom Main Shaft Bearing
Block, install the M2.6 x 15 socket head
bolts through the Front Pulley and
Main Shaft and then through the Auto
Rotation Assembly and Auto Rotation
Collar by aligning the holes in each
assembly with the corresponding holes
in the Main Shaft.
Note: Install the Main Shaft in the proper
direction as shown through the top bearing
block, then through the Main Shaft Collar,
Front Pulley, Main Drive Gear Assembly,
Auto Rotation Collar, Main Shaft Spacer, and
nally the bottom Main Shaft Bearing Block.
Be sure to loop the Tail Drive Belt around
the Front Pulley in the direction shown
previously in step 2-9.

18
41 ASSEMBLING THE SWASHPLATE AND WASHOUT ASSEMBLY
42 ATTACHING THE SWASHPLATE AND WASHOUT ASSEMBLY
Red(×7)
Red (×2)
Red(×2)
Degrease
Red (×2)
SocketHeadBolt,M2×15
……×1
Red
FlatHeadScrew,M2×8
……………×9
SocketHeadBolt,M2.6×10
…………×2
Flat Head Screw, M2 x 8 (9 Pcs)
Socket Head Screw,
M2.6 x 10 (2 Pcs)
Socket Head Bolt, M2 x 15
120° Swashplate Assembly
Washout Arm Collar (2 Pcs)
Washout Arm (2 Pcs)
Washout Base
Swash Pin
Joint Ball (9 Pcs)
Note: Assemble
2 Washout Arm
Assemblies
Apply a light even
coat of red threadlock
to uniformly adhere
Note: Slide the Swashplate onto
the Main Shaft. Install the M2 x 15
and Swash Pin onto the Swashplate
going through the Radius Support
as shown. Next install the Washout
Assembly onto the Main Shaft and
install the Washout links onto the
Joint balls on the Swashplate as
shown.

19
43 ASSEMBLING THE MAIN BLADE HOLDER AND ROTOR HUB 1
44 ASSEMBLING THE MAIN BLADE HOLDER AND ROTOR HUB 2
Red
Red(×2)
SocketHeadBolt,M3×6
…………×1
O-Ring5.2×10.4×2.6
…………×4
SocketHeadBolt,M3×10
………×2
FlatWasher,M3
………………×2
GripSpacer
…×2
SpindleWasher
…×2
Red (×2)
(×2)
Grease
Socket Head Bolt, M3 x 6
Socket Head Bolt,
M3 x 10 (2 Pcs)
Head Button
O-ring 5.2 x 10.4 x 2.6 (4 Pcs)
Main Blade Holder Assembly (2 Pcs)
Ball Arm (2 Pcs)
Main Rotor Hub
Smaller I.D.
Larger I.D.
Spindle Shaft
Grip Spacer (2 Pcs)
Thrust Bearing T5-10 (2 Pcs)
Spindle Washer (2 Pcs)
Flat Washer, M3 (2 Pcs)
Parts Bags 1=50°
2=70°
For 3D performance
install 70° O-rings
Note:
Assemble 2
Main Blade
Holder sets.
Note: Apply a small amount of Thrust Bearing
Grease to the Thrust Bearing
Note: If it is dicult to install the Spindle Shaft
through the O-ring dampeners, apply a small
amount of O-ring lubricant.
Note: The larger and smaller inner diameter Thrust
Bearing must be installed as shown.
Install the thrust BB CAGE toward the Main Shaft,
exposed balls to the Blade side of the grip. (The
thrust race will keep grease in, and positioning
the cage this way will prevent any possible cage
deformation from balls jamming on the cage that will
be thrown outward during use.)

20
45 ATTACHING THE SEESAW
46 ATTACHING THE SEESAW ARM
ButtonHeadBolt,M2.5×6
……………×2
SeesawcenterCollar
………………×2
Degrease
Red(×2)
Red(×2)
Red (×4)
Red(×2)
Degrease
FlatHeadScrew,M2×8
……………×4
SocketHeadBolt,M2.6×14
………×2
FlatWasher,2.6×4 . 5×0.5
…………………×2
Seesaw Center Collar (2 Pcs)
Joint Ball (4 Pcs)
Flange
Inner Hole
Flat Head Screw, M2 x 8 (4 Pcs)
Socket Head Bolt, M2.6 x 14 (2 Pcs)
Washer, 2.6 x 4.5 x 0.5 (2 Pcs)
Seesaw Arm Collar (2 Pcs)
Button Head Bolt, M2.5 x 6 (2 Pcs)
Seesaw Assembly
3D Seesaw Arm(2 Pcs)
Apply a light, even
coat of red threadlock
to uniformly adhere.
Apply a light, even
coat of red threadlock
to uniformly adhere.
Note: The Seesaw Arm is installed
with the bearing retaining ange
toward the Seesaw Arm. For 3D
ight attach the joint ball to the
outer hole.