Horizont E Series User manual

English
HORIZONT
R
E- Professional

User Manual
Version 1.2
English
Thanks for your purchase E series (60/80/100m) digital laser distance meter.
The safety instructions alone with the user manual should
read carefully before initial operation. Helpful Hint:The first and last page
including the pictures should look first,whilst reading through the
manual.Letters and Numbers in braces {} refer to the illustrations.
Use of the instrument
Permitted use
• Measuring distances
• Computing functions, e. g. areas and volumes
• Digital pointfinder functions
• Measuring tilts
Prohibited use
• Using the instrument without instruction
• Using outside the stated limits
• Deactivation of safety systems and removal of explanatory and hazard
labels
• Opening of the equipment by using tools (screwdrivers, etc.), as far as
not specifically permitted for certain cases
• Carrying out modification or conversion of the product
• Use of accessories from other manufacturers without the express
approval of Leica Geosystems

Keypad
Keypad function:
1、“ ”key：
Short press: Single distance Measuring；
Long press: Minimum/Maximum Measuring.
2、“ ”key：
Short press: Addition measurement.(Under measuring mode)；
Positive check the last 20 displays in the storage. (Under
navigating data in the storage)
3、“ ”key：
Short press: Addition measurement.(Under measuring mode)；
Negative check the last 20 displays in the storage. (Under
navigating data in the storage)
4、“ ”area/volume key：
Function Select of area or volume measure.
5、“ ” Indirect measurement：
The instrument can calculate distances using Pythagoras’ theorem.
6、“ ”Measurement reference key:
Short press: Change the measurement reference on “front”/“end”.
Long perss: Change the light intensity of the LCD with keys of
7、“ ”units/storage key：
Short press: Push display data into the storage;
Short press twice: Show the last 180 displays in reverse order.
Long press:Change the unit whitch need to deal with,(mm，inch，ft）.
8、“ ”clear/off key：
Short press: Clear the last entry or measurement.Within a function
(area,volume,etc.) single measurements can be deleted step by step and
re-measure.
Long press: Turn off the system.

9、“ ” Digital pointfinder key:
The device has an integral digital pointfinder, which shows the target directly
on the display. The displayed crosshairs allow precise measu-rements to be
made even though the laser beam is not visible.
Short press: Enter the digital targeting interface (zoom step 1x).
Chang zoom step 1x-2x.
Display
Display:B display in normal mode
1. Program selection with measurement instructions
2.Program selection submenu
3.Measurement field
4.Result bar
5.Status bar with (Laser ON, Reference plane, Display Long range mode,
Battery status)
Display C: display in “digital pointfinder” mode

1.Image 2.Crosshairs
3.Distance tracking value 4. Zoom step (1x, 2x)
The device has an integral digital pointfinder, which shows the target
directly on the display. The displayed crosshairs allow precise measu-
rements to be made even though the laser beam is not visible
The integral coloured digital pointfinder is a great help outdoors and can
be used in every function. Longer distances and precise measurements on
detailed surfaces can even be accomplished in bright sunlight without any
problem
Parallax errors occur when the digital pointfinder is used on close
targets, the laser dot may appear displaced in the crosshair. In this case you
should rely on the actual laser dot for targeting the object
1．E series provide up to national standard lithium charger kit.When the lowest
charge button show in the display,the product needs to be charged.
2．he first charge please continue to charge 12 hours
3．lease use the original charging Charger Kit.When finished ,please power
off.

*
*
Selecting Units
Long press key to change unit.Possible units：
Operation
Simple operation
1、Open /Close system
Open: Long press
Close: Long press
Note: The device will automatically turn off after 3 minutes of inactivity.
2、Clear or exit function
Short press ,clear the last entry or measurement. Within a function
(area,volume,etc.) single measurements can be deleted step by step and
re-measure.
3、Addition / subtraction
Distance measuring:
The next measurement is added to the previous one. Press
The next measurement is subtracted from the previous one.press
result is always shown in the summary line.
4、Reference setting
The default reference setting is from the rear of the instrument.
Press to take the next measurement from the front edge
pressing the key for longer show picture, you can now adjust the
brightness of the display using the or the key. Display
illumination has six levels of adjustment. Step 6 is the brightest and step 1 is
the darkest setting.
5、Single Distance Measuring
Short press key to open Laser。Aim at the desired target and press
key again. The measured distance is displayed immediately in the summary
line.
Distance Area Volume
0.000 m 0.000 m2 0.000 m3
0.000 ft 0.000 ft2 0.000 ft3
0.000 in 0.000 in2 0.000 in3

6、Minimum/Maximum Measuring
This function allows the user to measure the minimum/maximum distance
from a fixed measuring point. It is commonly used to measure diagonal
distances (maximum values) or horizontal distances (minimum values).
Long press key until you hear a beep, indicating the device is in a
continuous measuring mode. Then slowly sweep the laser back and forth
respectively up and down over the desires target point.
Press key again and the continuous measurement will be stopped. the
maximum and minimum distances are shown in Intermediate line 1 and
7、Area
Press Area/Volume key. The corresponding symbol appears in
the display. Take two measurements, the result will be displayed in the main.
8、Volume
Press area/volume key twice. The corresponding symbol appears
in the display. Take three distance measurements, the result will be displayed
in the main.
9、Indirect measurement
The instrument can calculate distances using Pythagoras’ theorem.
Make sure you adhere to the prescribed sequence of measurement:
l All target points must be in a horizontal or vertical plane.
l The best results are achieved when the instrument is rotated about a fixed
point.
l The minimum/maximum function can be used.
Make sure that the first measurement and the distance to be measured are
at right angles.
1、Indirect measurement - determining a distance using 2 auxilliary
measurements
Indirect measurement 1

Short press key once，The corresponding symbol “ ” appears
in the display. Aim at the upper point (1) and trigger the measurement.
After the first measurement the value is adopted. Keep the instrument as
horizontal as possible. Aim at the point (2) and trigger the measurement,
the partial results in Intermediate line 1 and line 2, and the result (the red line)
will be displayed in the main.
2、Indirect Measurement - determining a distance using 3 Measurements
Indirect measurement 2
Press this button twice; the display shows the following symbol .
The laser is switched on.Aim at the upper point (1) and trigger the
measurement; Aim at the upper point (2) and trigger the measurement.
After the second measurement the value is adopted. Keep the instrument as
horizontal as possible. Aim at the point (3) and trigger the measurement,
the partial results in Intermediate line 1 ~ line 3, and the result (the red line)
will be displayed in the main.
3、Indirect measurement - determining a distance using 3 auxilliary
measurements
Indirect measurement 3
Short press key thrice ，The corresponding symbol “ ”
appears in the display. Aim at the upper point (1) and trigger the
measurement; Aim at the upper point (2) and trigger the measurement.
After the second measurement the value is adopted. Keep the instrument as
horizontal as possible. Aim at the point (3) and trigger the measurement,
the partial results in Intermediate line 1 ~ line 3, and the result (the red line)
will be displayed in the main.

the partial results in Intermediate line 1 ~ line 3, and the result (the red line)
will be displayed in the main.
10、Historical storage
Short press key to push the display data into storage. “ c” expressed
store of success, and the last 180 data and 45 combined data displays are
showed in reverse order. Using the key and key allows to
navigate in the storage.
In order to leave the storage press key.
11、Tilt measurement 1:Direct vertical distance
Notice:
1、The inclination sensor measures tilts between ± 90°
2、the device is used with section ±0.5°
The inclination sensor measures tilts between +/-90°，The infocode i 271
means that the device has been set outside the permissible limits.press the
key four times-the angle symbol appears in the display.press the
to measure the inclination and distance.
Tilt measurement 2:Direct horizontal distance
Press key five times- symbol appears in the display,the tilt is
continuously shown,press key to open laser,press it again to take
horizontal distance.
1、hypotenuse
1、bertical edge
1、hypotenuse
2、hypotenuse

12、Stake out function
Two different distances (a and b) can be entered into the instrument and
can then be used to mark off defined measured lengths.
Press this button six times and the stake out function symbol
appears in the display.by using and ,you can adjust the values (first a
and then b) to suit the desired stake out distances. Holding the buttons down
increases
the rate of change of the values. Once the desired value (a)has been reached it
can be confirmed with the button. Value (b) can be entered using
and . The defined value (b) is confirmed with the button. Pressing
the button starts the laser measurement. The display shows required
stake out distance in the summary line between the stake out oint (first a and
then b) and the instrument (rear reference). The arrows in the display
indicate in which direction theE series needs to be moved in order to achieve
the defined distance(either a or b). As soon as the staking out point is reached,
the symbol appears in the display.
Press the key to return last function or stop measurement.
Message Codes
The following mistakes can be corrected:
Info Cause Remedy
205 Ranging transfinite Use in allowed ranging
252 Temperature too high Cool down instrument
253 Temperature too low Warm up instrument
255 Receiver signal too weak, measurement
time too long Use target plate
256 Received signal too powerful Use target plate
270 Error of hardware
Open/close the insteument
Repeatedly
271 Measuring angel＞90° Measuring angel（0-90°）
272 Computation errors Repead steps
abb