Hoshizaki Steelheart PR46A User manual

Models
Refrigerated Prep Table with Raised Rail
Steelheart Series
Refrigerated Kitchen Equipment
Instruction Manual
Issued: 8-26-2020
hoshizakiamerica.com

2
WARNING
Only qualied service technicians should install and service the appliance. To
obtain the name and phone number of your local Hoshizaki Certied Service
Representative, visit www.hoshizaki.com. No installation or service should be
undertaken until the technician has thoroughly read this Instruction Manual.
Likewise, the owner/manager should not proceed to operate the appliance until the
installer has instructed them on its proper operation. Failure to install, operate, and
maintain the appliance in accordance with this manual may adversely affect safety,
performance, component life, and warranty coverage. Proper installation is the
responsibility of the installer. Product failure or property damage due to improper
installation is not covered under warranty.
Hoshizaki provides this manual primarily to assist qualied service technicians in the
installation, maintenance, and service of the appliance.
Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, send an e-mail message, or write to the Hoshizaki Technical
Support Department for assistance.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
618 Highway 74 South
Peachtree City, GA 30269
Attn: Hoshizaki Technical Support Department
Web Site: www.hoshizaki.com
NOTE: To expedite assistance, all correspondence/communication MUST include the
following information:
• Model Number
• Serial Number
• Complete and detailed explanation of the problem.

3
CONTENTS
Important Safety Information ................................................................................................. 4
I. Installation Instructions ....................................................................................................... 8
A. Location ........................................................................................................................ 8
B. Checks Before Installation............................................................................................. 9
C. Setup............................................................................................................................. 9
D. Door Reversal.............................................................................................................. 13
E. Door/Drawer Reversal................................................................................................. 17
F. Electrical Connection ................................................................................................... 24
G. Final Checklist ............................................................................................................ 25
II. Operating Instructions...................................................................................................... 26
A. Important Notes About Usage..................................................................................... 26
B. Startup ........................................................................................................................ 29
C. Controls and Adjustments ........................................................................................... 29
1. Temperature Display............................................................................................... 29
2. Adjusting the Temperature Setpoint and Rail and Cabinet Cooling ....................... 30
3. Changing the Temperature Display Scale (°F or °C) ............................................. 31
D. Control Module Icons .................................................................................................. 31
E. Defrost......................................................................................................................... 32
F. Alarm Safeties.............................................................................................................. 33
G. Food Storage .............................................................................................................. 34
H. Safety Devices ............................................................................................................ 34
I. Cooling Performance.................................................................................................... 35
J. Cabinet Condensation ................................................................................................. 35
III. Cleaning and Maintenance Instructions.......................................................................... 36
A. Cleaning...................................................................................................................... 36
1. Exterior................................................................................................................... 36
2. Cabinet Interior ...................................................................................................... 36
3. Door/Drawer Gaskets ............................................................................................ 36
4. Shelves.................................................................................................................. 36
5. Drawers ................................................................................................................. 37
6. Cutting Board......................................................................................................... 37
7. Pans ....................................................................................................................... 37
8. Rail, Rail Dividers, and Rail Cover......................................................................... 37
9. Rail Air Duct........................................................................................................... 38
B. Maintenance................................................................................................................ 39
1. Air Filter .................................................................................................................. 39
2. Condenser............................................................................................................. 39
3. Condensate Drain.................................................................................................. 40
4. Power Supply Connection...................................................................................... 40
IV. Preparing the Appliance for Periods of Non-Use ............................................................ 41
V. Disposal........................................................................................................................... 42
IMPORTANT
This manual should be read carefully before the appliance is installed and operated.
Read the warnings and guidelines contained in this booklet carefully as they
provide essential information for the continued safe use and maintenance of the
appliance. Retain this booklet for any further reference that may be necessary.

4
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.
DANGER Indicates a hazardous situation that, if not avoided, will result in
death or serious injury.
WARNING Indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
NOTICE Indicates a situation that, if not avoided, could result in damage
to the appliance or property.
IMPORTANT Indicates important information about the use and care of the
appliance.
DANGER
Risk of Fire or Explosion
Flammable Refrigerant Used
• Follow handling instructions carefully
in compliance with U.S. government
regulations.
• Do not use mechanical devices to defrost.
• Do not puncture refrigerant tubing. Risk
of re or explosion due to puncture
of refrigerant tubing; follow handling
instructions carefully.
• Component parts shall be replaced with
like components.
• Servicing shall be done by factory
authorized service personnel to minimize
the risk of possible ignition due to
incorrect parts or improper service.
• Consult instruction manual/service manual
before attempting to install or service this
product. All safety precautions must be
followed.
• Dispose of properly in accordance with
federal or local regulations.
• Do not place any potential ignition sources
in or near the appliance.
Risque De Feu Ou D'Explosion
Le Frigorigène Est Inammable
• Suivre attentivement les instructions
de manipulation conformément à la
réglementation gouvernementale.
• Ne pas utiliser d'appareils mécaniques
pour dégivrer le réfrigérateur.
• Ne pas perforer la tubulure contenant le
frigorigène. Risque de feu ou d'explosion
si la tubulure contenant le frigorigène
est perforée; suivre les instructions de
manutention avec soin.
• Les pièces des composants doivent être
remplacées par des pièces et accessoires
équivalents.
• L’entretien doit être effectué par le
personnel de service autorisé par le
fabricant an de minimiser les risques
d’inammation attribuables à l’installation
d’une pièce inadéquate ou à la mauvaise
exécution du service.
• Consulter le manuel du propriétaire/
guide de réparation avant de tenter une
réparation. Toutes les mesures de sécurité
doivent être respectées.
• Éliminer conformément aux règlements
fédéraux ou locaux.
• Ne placez aucune source d’inammation
potentielle dans ou près de l’appareil.

5
WARNING
The appliance should be destined only to
the use for which it has been expressly
conceived. Any other use should be
considered improper and therefore
dangerous. The manufacturer cannot be
held responsible for injury or damage
resulting from improper, incorrect, and
unreasonable use. Failure to install,
operate, and maintain the appliance
in accordance with this manual will
adversely affect safety, performance,
component life, and warranty coverage.
To reduce the risk of death, electric
shock, serious injury, or re, follow
basic precautions including the
following:
• Only qualied service technicians should
install and service the appliance.
• Wear appropriate personal protective
equipment (PPE) when servicing the
appliance.
• The appliance must be installed in
accordance with applicable national, state,
and local codes and regulations.
• Appliance is heavy. Use care when
lifting or positioning. Work in pairs when
needed to prevent injury or damage. Do
not lift using the top section or the doors/
drawers.
• To reduce the risk of electric shock, do not
touch the plug with damp hands.
• Unplug the appliance before servicing.
• The appliance requires an independent
power supply of proper capacity. See the
nameplate for electrical specications.
Failure to use an independent power
supply of proper capacity can result in a
tripped breaker, blown fuse, damage to
existing wiring, or component failure. This
could lead to heat generation or re.
• THE APPLIANCE MUST BE
GROUNDED. The appliance is equipped
with a NEMA5-15 three-prong grounding
plug to reduce the risk of potential
shock hazards. It must be plugged into a
properly grounded, independent 3-prong
wall outlet. If the outlet is a 2-prong outlet,
it is your personal responsibility to have
a qualied electrician replace it with a
properly grounded, independent 3-prong
wall outlet. Do not remove the ground
prong from the power cord and do not use
an adapter plug. Failure to follow these
instructions may result in death, electric
shock, or re.
• Do not use an extension cord.
• Do not use an appliance with a damaged
power cord. The power cord should not be
altered, jerked, bundled, weighed down,
pinched, or tangled. Such actions could
result in electric shock or re. To unplug
the appliance, be sure to pull the plug, not
the cord, and do not jerk the cord.
• The GREEN ground wire in the
factory-installed power cord is connected
to the appliance. If it becomes necessary
to remove or replace the power cord, be
sure to connect the power cord's ground
wire.
• Do not splash, pour, or spray water
directly onto or into the appliance. This
might cause short circuit, electric shock,
corrosion, or failure.
• Do not make any alterations to the
appliance. Alterations could result in
electric shock, injury, re, or damage to
the appliance.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory, or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for their
safety.

6
• Do not block air inlets or outlets, otherwise
cooling performance may be reduced.
• Do not tightly pack the cabinet. Allow some
space between items to ensure good air
ow. Also allow space between items and
interior surfaces.
• Do not put warm or hot foods in the cabinet.
Let them cool rst, or they will raise the
cabinet temperature and could deteriorate
other foods in the cabinet or overload the
appliance.
• Food storage and handling must comply
with applicable codes and regulations.
• All foods should be wrapped in plastic lm
or stored in sealed containers. Otherwise
foods may dry up, pass their smells onto
other foods, cause frost to develop, result
in poor appliance performance, or increase
the likelihood of cross-contamination.
Certain dressings and food ingredients,
if not stored in sealed containers, may
accelerate corrosion of the evaporator,
resulting in failure.
• Do not store items near air outlets.
Otherwise, items may freeze up and
crack or break causing a risk of injury or
contamination of other food.
WARNING, continued
• Children should be properly supervised
around the appliance.
• Do not climb, stand, or hang on the
appliance or doors/drawers or allow
children or animals to do so. Do not climb
into the appliance or allow children or
animals to do so. Death or serious injury
could occur or the appliance could be
damaged.
• Be careful not to pinch ngers when
opening and closing the doors/drawers
or rail cover (prep table models) or when
handling food pans. Be careful when
opening and closing the doors/drawers or
rail cover when children are in the area.
• Open and close the doors/drawers and
rail cover with care. Opening the doors/
drawers or rail cover too quickly or
forcefully may cause injury or damage to
the appliance or surrounding equipment.
• Do not use combustible spray or place
volatile or ammable substances in or near
the appliance. They might catch re.
• Keep the area around the appliance clean.
Dirt, dust, or insects in the appliance could
cause harm to individuals or damage to
the equipment.
• Do not throw anything onto the shelves or
load any single shelf with more than 120lb.
(54.5 kg) of product. They might fall off and
cause injury.
• Do not load any single drawer with more
than 75 lb. (34 kg) of product. Depending
on the weight of product in the drawers,
secure the unit as necessary to prevent it
from overturning. Do not open more than
one drawer at a time.
• The appliance is designed only for
temporary storage of food. Employ sanitary
methods. Use for any other purposes (for
example, storage of chemicals or medical
supplies such as vaccine and serum)
could cause deterioration of stored items.

7
NOTICE
• Protect the oor when moving the
appliance to prevent damage to the oor.
• Keep ventilation openings, in the
appliance enclosure or in the built-in
structure, clear of obstruction. Do not
place anything on top of the appliance in
an undercounter installation. There must
be at least 1.5" (4 cm) overhead clearance
for proper ventilation. The factory-installed
rear bumpers must be in place to ensure
proper rear clearance. Blockage of airow
could negatively affect performance and
damage the appliance.
• Do not allow the appliance to bear any
outside weight.
• To prevent deformation or cracks, do not
spray insecticide onto the plastic parts or
let them come into contact with oil.
• To avoid damage to the gasket, use only
the door/drawer handle when opening
and closing.
• Do not leave the doors/drawers open.
• To avoid damage to the top seal, do not lift
the appliance by the top panel or remove
the top panel.
• Do not place anything on top of the rail
hood or rail cover and do not lift the
appliance by the rail hood or rail cover.
The rail hood and rail cover are not
designed to bear any outside weight.
• Do not place anything on the air duct
panels beneath the pans in the rail.
The air duct panels are not load-bearing.
WARNING, continued
Additional Warnings for Prep Table
Models
• The entire rail must always be covered
by rail dividers and pans. Otherwise, the
appliance will not cool properly. Use only
pans up to 6"(15cm) deep.
Do not use damaged rail dividers or pans.
• Ingredients must be pre-chilled to 37°F
(3°C) or less before placing in rail.
• Keep the rail cover closed when not actively
preparing food.
• The rail is for keeping ingredients cool while
preparing food. If not actively preparing
food for a long period such as overnight,
seal pans with plastic wrap in addition
to closing the rail cover. Depending on
conditions, the cabinet temperature setting
may need to be adjusted to prevent items
from freezing. Alternatively, seal ingredients
and store them in a refrigerator or freezer.
• For PR46(-D) models, the anti-tip bracket
must be properly installed and adjusted.
Otherwise, the unit may tip, resulting in
injury or damage.

8
I. Installation Instructions
WARNING
• The appliance must be installed in accordance with all applicable national, state,
and local regulations.
• Appliance is heavy. Use care when lifting or positioning. Work in pairs when needed
to prevent injury or damage. Do not lift using the refrigeration area, the top section,
or the doors/drawers.
• Do not tilt the appliance more than 45°.
A. Location
WARNING
• The appliance is not intended for outdoor use.
• Certied to maintain NSF temperatures between 45°F to 86°F (7°C to 30°C).
Engineered to maintain NSF temperatures up to 100°F (38°C).
• Operation of the appliance, for extended periods, outside of these temperature
ranges may affect appliance performance.
For best operating results:
• The appliance should not be located next to ovens, grills, or other high heat producing
equipment.
• The location should provide a rm and level foundation for the appliance.
• The appliance should not be located in a corrosive environment.
• Allow 1" (3 cm) clearance at sides for proper air circulation. The factory-installed rear
bumpers must be in place to ensure proper rear clearance. A minimum of 10"(25cm)
clearance above the rail should be provided to allow the rail cover to open.

9
B. Checks Before Installation
WARNING
Refer to the nameplate for electrical specications. The nameplate is located on
the right side wall of the cabinet interior. For more electrical connection details, see
"I.F. Electrical Connection." We reserve the right to make specication and design
changes without prior notice.
• Visually inspect the exterior of the shipping package and immediately report any damage
to the carrier. Upon opening the package, any concealed damage should also be
immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. Also remove the protective
plastic lm from both the exterior panels and the interior door/drawer panel. If the
appliance is exposed to the sun or to heat, remove the lm after the appliance cools.
• Remove all accessory containers before discarding the packing materials. Dispose of all
packing materials in a proper and environmentally responsible manner.
• Check for missing or damaged accessories.
C. Setup
1. Remove the Appliance from the Pallet
1) Move as close to the nal location as possible.
2) Remove the 2 bolts securing the appliance to the pallet, then remove the appliance
from the pallet. Block the appliance securely at a height of 8" (20 cm) off the oor.
NOTICE! Do not place blocks under the refrigeration area or doors/drawers of the
appliance. Do not lay the appliance down.
3) Attach the casters to the bottom of the appliance. Locking casters should be attached
to the front of the appliance. See Fig. 1. NOTICE! Ensure casters are completely
threaded into appliance and tight.
Door
Locking Casters in Front
Fig. 1
Nameplate

10
2. Check the Refrigeration Circuit
Visually check that the refrigerant lines do not rub or touch other lines or surfaces and
that the condenser fan blade turns freely.
3. Position the Appliance and Lock the Front Casters
The front casters on the appliance are lockable. After positioning the appliance in its nal
location, lock the front casters.
4. For PR46(-D) Models, Install the Anti-Tip Bracket
1) Attach the anti-tip bracket to the bottom of the appliance with the two 4×8 T2 screws
provided. See Fig. 2.
2) Adjust the leg on the anti-tip bracket. The maximum gap between the leg and the oor
is 1/2" (13 mm) WARNING! The anti-tip bracket must be properly installed and
adjusted. Otherwise, the unit may tip, resulting in injury or damage.
Fig. 3
Shelf
Support Clip
Pilaster
Shelves
5. Install the Shelves
1) For each shelf, place the shelf support clips into the pilasters at the desired height
(4 shelf support clips per shelf). See Fig. 3.
2) Place the shelves in position on the support clips.
Fig. 2
Anti-Tip Bracket
4×8 T2 Screws
Adjust Leg
Maximum Gap
Between Leg and
Floor is 1/2" (13 mm)

11
6. Conrm Rail Cover Operation
The rail cover's rear pins are inserted into the rear slots on both brackets. Use the rail
cover's front pins and the notches on the brackets to place the rail cover in the open
position.You can use either set of notches. The hollow side of the rail cover faces down.
See Fig. 4. WARNING! When the rail cover is open, make sure the rear pins on both
sides of the rail cover are securely in the rear slots and the front pins are resting
securely in the notches. Otherwise, the rail cover could close suddenly and cause
injury.
7. Conrm Rail Dividers and Pans are in Place
Conrm rail dividers and 1/3 size pans included with the appliance are in place.
See Fig.5.
• The entire rail must always be covered by rail dividers and pans. Otherwise, the
appliance will not cool properly.
• Use only pans up to 6"(15cm) deep. Do not use damaged rail dividers or pans.
• Wash the pans before use.
• At startup, leave the pans empty until the appliance cools down.
• On some models, an extra rail divider is included. Use the extra rail divider if a gap
remains after all pans and all other rail dividers are in place. Some pans on the market
are slightly larger and do not require the extra rail divider.
Pans
Rail Dividers
Fig. 5
Fig. 4
Rear Pin
Rear Slot
Front Pin
Notches
Rail Cover
Model Shown: PR67A

12
8. Attach the Cutting Board
1) Loosen, but do not remove, the screws securing the cutting board brackets. See Fig. 6.
2) Slide the cutting board under the cutting board brackets, then tighten the screws.
WARNING! Make sure the cutting board brackets and cutting board are secure.
Otherwise, the cutting board could come off and cause injury.
Note: Wash the cutting board before use.
Fig. 6
Cutting Board Brackets
Cutting Board
Model Shown: PR67A

13
Lower Hinge Bracket
5) Remove the lower hinge bracket. See Fig. 9. Be sure to leave the thrust washer in place.
6) Clear the foam from the lower hinge bracket mounting holes prior to securing lower
hinge bracket in its new location. Install the lower hinge bracket in its new location. Be
sure the lower hinge bracket is pushed all the way in and the thrustwasher is in its
original position.
Fig. 9 Bolts
Thrust
Washer
D. Door Reversal
The appliance is provided with a cabinet design which, after being delivered to the
installation location, permits changing of the door swing from left to right or right to left. To
change the door swing, follow the steps below. Example shows change from right hinged
to left hinged.
WARNING
• Wear proper PPE (personal protection equipment) when executing these
procedures (safety glasses and gloves).
• Keep ngers away from edge of upper hinge bracket. Spring cartridge can cause
the upper hinge bracket to move suddenly with extreme force.
Door and Lower Hinge Removal and Relocation
1) Remove all items from the appliance. Make sure the appliance is unplugged from the
electrical outlet. Move the appliance out for ease of access then lock the casters.
2) With the door closed, loosen, but do not remove, the upper hinge bracket outer screw.
See Fig. 7. Next, open the door to the fully open position and remove the upper hinge
bracket inner screw. See Fig. 8.
3) Slide the upper hinge bracket out from under the outer screw and remove the door.
WARNING! Keep away from upper hinge bracket. Upper hinge bracket may spring
closed.
4) Replace the upper hinge bracket inner screw in its original position and tighten, then
tighten the upper hinge bracket outer screw.
Fig. 7 Fig. 8
Upper Hinge
Bracket Inner
Screw
Door Fully Open
WARNING! Upper
hinge bracket may
spring closed
Lower Hinge Bracket
Bolts
Thrust Washer
Fig. 10
Upper Hinge Bracket
Outer Screw
Door Closed
Upper Hinge Bracket
Upper Hinge
Bracket
Lower Hinge
Bracket
Mounting Holes

14
Upper Hinge
Bracket
Door
Fig. 11
Screw
Washer
Upper Hinge Bracket Removal and Spring Cartridge Relocation
7) While preventing the upper hinge bracket from rotating, remove the upper hinge bracket
from the spring cartridge. See Fig. 11. Note which side of the upper hinge bracket is
facing up.
8) Remove the ller cap, ller screws, and spring cartridge. See Fig. 12. Leave the thrust
washers in place on the spring cartridge. NOTICE! Spring cartridge may be difficult
to remove. Be careful not to damage the nish.
Filler Cap Door Spring Cartridge
Filler Screws
Thrust Washers
Screws
Fig. 12
9) Clear foam from the spring cartridge hole to allow for spring cartridge installation.
See Fig. 13. Install the spring cartridge in its new location. Reinstall the ller cap and
ller screws on the opposite side of the door.
Filler Screws
Filler Cap
Door
Spring Cartridge
Screws
Fig. 13
Lower Door Prep and Upper Hinge Bracket Relocation
10) Remove the ller cap and nylon bearing from the bottom of the door. SeeFig.14.
Reinstall on the opposite side.
11) Make sure the thrust washers are in place on the spring cartridge, then ip the upper
hinge bracket over from its original position and install onto the spring cartridge in
the door open position. See Fig. 15. The upper hinge bracket should be positioned as
shown.
Upper Hinge Bracket
Inside of
Door
Screw
Washer
Fig. 14 Fig. 15
Filler Cap
Nylon Bearing
Thrust Washers
Upper Hinge
Bracket Inner
Screw Hole
Spring Cartridge Hole
Upper Hinge
Bracket Outer
Screw Slot
Thrust
Washers

15
Door Installation
12) Remove the black plastic ller cap located from the hole above where the spring
cartridge screw will line up. Note: The black plastic ller cap is not reusable.
13) Remove the upper hinge bracket screws from the new location and apply Loctite
Threadlocker Blue 242 or 243 to the threads. Next, start the upper hinge bracket
outer screw into the appliance. Rotate a few threads into the appliance; do not tighten
thescrew. See Fig. 16.
14) Be sure the lower hinge bracket thrust washer is in place, then place the door on the
lower hinge bracket in the fully open position. Slide the door upper hinge bracket outer
slot onto the upper hinge bracket outer screw. See Fig. 17.
15) Install the upper hinge bracket inner screw and tighten.
Fig. 16
Fig. 17
Door Fully Open
Lower Hinge Bracket
Upper Hinge Bracket
Outer Screw
Upper Hinge
Bracket Outer
Screw
Door Fully Open
Upper Hinge
Bracket
Upper Hinge
Bracket Inner
Screw
Upper Hinge Bracket
Outer Screw
Upper Hinge
Bracket Inner
Screw
Black Plastic Filler Cap Upper Hinge
Bracket Outer
Screw
Upper Hinge
Bracket WARNING! Upper
hinge bracket may
spring closed
Thrust
Washer

16
16) Close the door and tighten the upper hinge bracket outer screw.
See Fig. 18.
Fig. 18
Upper Hinge
Bracket
Upper Hinge Bracket
Outer Screw
17) Check the door operation to assure it opens and closes properly. Note: Hold door at
45°angle from closed position and release. Door should close on its own. If not, adjust
hinge bracket.
18) Unlock the casters and move the appliance back into its original position. Lock the
casters once in position, then plug the appliance back into the electrical outlet. Allow the
appliance to cool down prior to putting product back in.
Door Fully Closed

17
3) Remove the 4 mullion screws, then cut the front mullion silicone loose and remove the
mullion. See Fig. 20.
Fig. 20
Mullion Screws
Mullion Silicone
Mullion Silicone
Mullion
E. Door/Drawer Reversal
The appliance is provided with a cabinet design which, after being delivered to the
installation location, permits changing of the drawer and door locations. To change the
drawer and door locations, follow the steps below.
WARNING
• Wear proper PPE (personal protection equipment) when executing these
procedures (safety glasses and gloves).
• Keep ngers away from edge of upper hinge bracket. Spring cartridge can cause
the upper hinge bracket to move suddenly with extreme force.
Drawer and Drawer Cartridge Removal
1) Remove all items from the appliance. Make sure the appliance is unplugged from the
electrical outlet. Move the appliance out for ease of access then lock the casters.
See Fig. 19.
2) Remove the drawers. Pull the drawer out to its fully extended position. Open the safety
clips (one on each side) by sliding them forward. Lift up slightly and remove them from
the drawer cartridge. See. "III.A.5. Drawers" for reference. Be sure to note which is the
upper drawer and which is the lower drawer.
Fig. 19
Upper Drawer
Lower Drawer
Drawer
Cartridge
Casters

18
4) Remove the 4 rear screws from the left and right drawer cartridge frames
(2 per side). See Fig. 21.
5) Remove the 8 front screws from the left and right drawer cartridge frames (4 per side),
then remove the cartridge frames from the unit.
Pilaster and Filler Screw Relocation
6) Remove the 12 pilaster ller screws from the current drawer section. See Fig. 22.
Fig. 21
Fig. 22
Rear Pilaster
Filler Screws
Rear Screws
Front Screws Left Drawer
Cartridge Frame
Right Drawer
Cartridge Frame
Front Pilaster
Filler Screws
Rear Pilaster
Filler Screws
Front Pilaster
Filler Screws

19
7) Remove the shelves from the door section, then remove the pilasters and place and
secure them in the new location (current drawer location). See Fig. 23. Note: Other than
in a center location, outer pilasters mount on the side wall not the rear wall.
8) Place and secure the pilaster ller screws removed in step 6 into the new drawer
location (current door location).
Shelves
Pilasters
Pilasters
9) Remove the drawer cartridge frame rear ller screws from the new location (current
door location). Place the drawer cartridge frame ller screws in the new door location
and tighten. Replace the shelves. See Fig. 24.
Fig. 23
Rear Filler
Screws
Shelves
Rear Filler
Screws
Fig. 24

20
Door Relocation
10) With the door closed, loosen, but do not remove, the upper hinge bracket outer screw.
See Fig. 25. Next, open the door to the fully open position and remove the upper hinge
bracket inner screw. See Fig. 26.
11) Slide the upper hinge bracket out from under the outer screw and remove the door.
WARNING! Keep away from upper hinge bracket. Upper hinge bracket may spring
closed.
12) Replace the upper hinge bracket inner screw in its original position and tighten, then
tighten the upper hinge bracket outer screw.
Upper Hinge
Bracket Outer
Screw
Door Closed
Upper Hinge
Bracket Inner
Screw
Door Fully Open
WARNING! Upper
hinge bracket may
spring closed
13) Remove the lower hinge bracket. See Fig. 27. Be sure to leave the thrust washer in
place.
14) Clear the foam from the lower hinge bracket mounting holes prior to securing the lower
hinge bracket in its new location. Install the lower hinge bracket in its new location. Be
sure the lower hinge bracket is pushed all the way in and the thrust washer is in its
original position.
Lower Hinge Bracket
Bolts
Thrust
Washer
Lower Hinge Bracket
Bolts
Thrust Washer
15) Remove the black plastic ller cap located from the hole above where the spring
cartridge screw will line up. Note: The black plastic ller cap is not reusable.
16) Remove the upper hinge bracket screws from the new location and apply Loctite
Threadlocker Blue 242 or 243 to the threads. Next, start the upper hinge bracket
outer screw into the appliance. Rotate a few threads into the appliance; do not tighten
thescrew. See Fig. 28.
Fig. 25
Fig. 27
Fig. 28
Upper Hinge Bracket
Upper Hinge Bracket
Upper Hinge Bracket
Outer Screw Upper Hinge
Bracket Inner
Screw
Black Plastic Filler Cap
Upper Hinge
Bracket Outer
Screw
Fig. 26
Lower Hinge
Bracket
Mounting Holes