Hoshizaki FM-1000AKE-R452-SB User manual

L1F054208 (083121)
Telford 70 Sta󰀨ord Park 7, Telford, Shropshire TF3 3BQ UK
MODULAR ICE MAKER
MACHINE A GLACE MODULAIRE
EISBEREITER FÜR SEPARATEN VORRATSBEHÄLTER
IJSMACHINE MET LOSSE OPSLAGBUNKER
MAQUINA DE CUBITOS MODULAR
FABBRICATORE MODULARE DI GHIACCIO
FOR END USER
POUR UTILISATEUR
FÜR DEN ENDKUNDEN
VOOR DE GEBRUIKER
PARA USUARIO
PER L’UTENTE FINALE
INSTRUCTION MANUAL
(original instructions)
NOTICE D’UTILISATION
(instructions traduites)
BEDIENUNGSANLEITUNG
(Übersetzung)
GEBRUIKSAANWIJZING
(vertaalde instructies)
MANUAL DE INSTRUCCIONES
(instrucciones traducidas)
MANUALE D’ISTRUZIONI
(traduzione)
FM-480AKE
FM-1000AKE
FM-1000AKE-N
FM-750AKE
FM-750AKE-N
FM-600AKE
FM-600AKE-N
FM-600AWKE
FM-600AWKE-N
FM-480AKE
FM-480AKE-N
FM-480AWKE
FM-480AWKE-N
FM-300AKE
FM-300AKE-N
FM-170AKE
FM-170AKE-N
FM-1000AKE-R452-SB
FM-1000AKE-R452N-SB
FM-750AKE-R452-SB
FM-750AKE-R452N-SB
FM-600AKE-R452-SB
FM-600AKE-R452N-SB
FM-600AWKE-R452-SB
FM-600AWKE-R452N-SB
FM-480AWKE-R452-SB
FM-480AWKE-R452N-SB

IMPORTANT SAFETY INFORMATION ................................................................................................. 1
I. INSTALLATION INSTRUCTIONS..................................................................................................... 3
1. CONSTRUCTION........................................................................................................................ 3
2. LOCATION .................................................................................................................................. 3
3. ELECTRICAL CONNECTIONS................................................................................................... 3
4. WATER SUPPLY AND DRAIN CONNECTIONS........................................................................ 4
II. OPERATING INSTRUCTIONS......................................................................................................... 4
1. START UP................................................................................................................................... 5
2. SHUT DOWN .............................................................................................................................. 5
3. PREPARING THE ICEMAKER FOR LONG STORAGE............................................................. 5
III. MAINTENANCE................................................................................................................................ 6
1. CLEANING .................................................................................................................................. 6
2. INSPECTION AND MAINTENANCE........................................................................................... 7
3. BEFORE CALLING FOR SERVICE............................................................................................ 7
4. DISPOSAL................................................................................................................................... 8
5. WARRANTY................................................................................................................................ 8
SPECIFICATIONS.................................................................................................................................. 9
INFORMATIONS DE SECURITE IMPORTANTES .............................................................................. 14
I. CONSIGNES D’INSTALLATION..................................................................................................... 16
1. CONSTRUCTION...................................................................................................................... 16
2. EMPLACEMENT ....................................................................................................................... 16
3. BRANCHEMENTS ELECTRIQUES.......................................................................................... 16
4. BRANCHEMENTS D’ARRIVEE ET DE VIDANGE D’EAU........................................................ 17
II. CONSIGNES D’UTILISATION........................................................................................................ 17
1. MISE EN MARCHE ................................................................................................................... 18
2. ARRET ...................................................................................................................................... 18
3. PREPARATION DU DISTRIBUTEUR DE GLACE EN VUE D’UN ENTREPOSAGE
DE LONGUE DUREE................................................................................................................ 18
III. ENTRETIEN.................................................................................................................................... 19
1. NETTOYAGE ............................................................................................................................ 19
2. INSPECTION ET ENTRETIEN.................................................................................................. 20
3. AVANT D’APPELER UN REPARATEUR.................................................................................. 21
4. MISE AU REBUT....................................................................................................................... 22
5. GARANTIE ................................................................................................................................ 22
SPECIFICATIONS................................................................................................................................ 23
WICHTIGE SICHERHEITSHINWEISE................................................................................................. 28
I. INSTALLATIONSANLEITUNG........................................................................................................ 30
1. KONSTRUKTION...................................................................................................................... 30
2. AUFSTELLORT......................................................................................................................... 30
3. ELEKTRISCHE ANSCHLÜSSE ................................................................................................ 30
4. WASSERZULAUF- UND WASSERABLAUFANSCHLÜSSE.................................................... 31
II. BEDIENUNGSANLEITUNG............................................................................................................ 31
1. INBETRIEBNAHME................................................................................................................... 32
2. AUSSCHALTEN........................................................................................................................ 32
3. MASSNAHMEN FÜR DIE LANGFRISTIGE LAGERUNG DES EISSPENDERS...................... 32
III. WARTUNG...................................................................................................................................... 33
1. REINIGUNG .............................................................................................................................. 33
2. INSPEKTION UND WARTUNG ................................................................................................ 34
3. VOR ANRUF DES KUNDENDIENSTES................................................................................... 35
4. ENTSORGUNG......................................................................................................................... 36
5. GEWÄHRLEISTUNG ................................................................................................................ 36
TECHNISCHE DATEN ......................................................................................................................... 37
ENGLISH
FRANCAIS
DEUTSCH

BELANGRIJKE VEILIGHEIDSINFORMATIE ....................................................................................... 42
I. INSTALLATIE-INSTRUCTIES ........................................................................................................ 44
1. CONSTRUCTIE......................................................................................................................... 44
2. PLAATSING .............................................................................................................................. 44
3. ELEKTRISCHE AANSLUITINGEN............................................................................................ 44
4. AANSLUITING VAN WATERTOEVOER- EN WATERAFVOERLEIDINGEN ........................... 45
II. BEDIENINGSINSTRUCTIES.......................................................................................................... 45
1. OPSTARTEN............................................................................................................................. 46
2. UITZETTEN............................................................................................................................... 46
3. DE IJSMAKER GEREEDMAKEN VOOR LANGDURIGE OPSLAG ......................................... 46
III. ONDERHOUD................................................................................................................................. 47
1. REINIGEN ................................................................................................................................. 47
2. INSPECTIE EN ONDERHOUD................................................................................................. 48
3. VOORDAT U BELT VOOR SERVICE....................................................................................... 49
4. VERWIJDERING....................................................................................................................... 50
5. GARANTIE ................................................................................................................................ 50
SPECIFICATIES................................................................................................................................... 51
INFORMACIÓN IMPORTANTE DE SEGURIDAD ............................................................................... 56
I. INSTRUCCIONES DE INSTALACIÓN ........................................................................................... 58
1. CONSTRUCCIÓN ..................................................................................................................... 58
2. UBICACIÓN............................................................................................................................... 58
3. CONEXIONES ELÉCTRICAS................................................................................................... 58
4. SUMINISTRO DE AGUA Y CONEXIONES DE DRENAJE....................................................... 59
II. INSTRUCCIONES DE UTILIZACIÓN............................................................................................. 59
1. PUESTA EN MARCHA.............................................................................................................. 60
2. DESCONEXIÓN........................................................................................................................ 60
3. PREPARACIÓN DE LA MÁQUINA DE HIELO PARA UN ALMACENAMIENTO
PROLONGADO......................................................................................................................... 60
III. MANTENIMIENTO.......................................................................................................................... 61
1. LIMPIEZA .................................................................................................................................. 61
2. REVISIÓN Y MANTENIMIENTO............................................................................................... 62
3. ANTES DE LLAMAR AL SERVICIO TÉCNICO ........................................................................ 63
4. ELIMINACIÓN ........................................................................................................................... 64
5. GARANTÍA ................................................................................................................................ 64
ESPECIFICACIONES........................................................................................................................... 65
INFORMAZIONI IMPORTANTI SULLA SICUREZZA........................................................................... 70
I. ISTRUZIONI PER L’INSTALLAZIONE............................................................................................ 72
1. COMPONENTI .......................................................................................................................... 72
2. UBICAZIONE............................................................................................................................. 72
3. COLLEGAMENTI ELETTRICI................................................................................................... 72
4. COLLEGAMENTO DI ALIMENTAZIONE DELL’ACQUA E COLLEGAMENTO DI
SCARICO .................................................................................................................................. 73
II. ISTRUZIONI DI FUNZIONAMENTO............................................................................................... 73
1. AVVIO........................................................................................................................................ 74
2. ARRESTO ................................................................................................................................. 74
3. PREPARATIVI PER IL LUNGO IMMAGAZZINAGGIO DELLA MACCHINA............................. 74
III. MANUTENZIONE ........................................................................................................................... 75
1. PULIZIA..................................................................................................................................... 75
2. CONTROLLO E MANUTENZIONE........................................................................................... 76
3. PRIMA DI RIVOLGERSI ALL’ASSISTENZA............................................................................. 77
4. SMALTIMENTO......................................................................................................................... 78
5. GARANZIA ................................................................................................................................ 78
SPECIFICHE ........................................................................................................................................ 79
NEDERLANDS
ESPAÑOL
ITALIANO

1
ENGLISH
IMPORTANT SAFETY INFORMATION
Throughout this manual, notices appear to bring your attention to situations which could result in
death, serious injury, or damage to the unit.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTICE Indicates a hazardous situation which, if not avoided, could result in damage to
the unit.
HYGIENE Indicates important precautions for hygiene and food safety.
IMPORTANT Indicates important information about the use and care of the unit.
IMPORTANT
This booklet is an integral and essential part of the product and should be kept and preserved
by the user.
Please read carefully the guidelines and warnings contained herein as they are intended to
provide the user with essential information for the continued safe use and maintenance of the
product. In addition, it provides GUIDANCE ONLY to the user on the correct services and site
location of the icemaker.
Please preserve this booklet for any further consultation that may be necessary.
WARNING
This is a commercial icemaker, and should be destined only to be used for the purpose for
which it has been expressly designed and attached to a suitable storage bin as specied by
Hoshizaki.
Any other use should be considered improper and therefore dangerous. The manufacturer
will not be held liable or responsible for any damage caused by improper, incorrect and
unreasonable use.
The installation, and relocation if necessary, must be carried out by qualied personnel,
in accordance with current regulations, according to the manufacturer’s instructions.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.

2
ENGLISH
The use of any electrical appliance involves the observance of some fundamental rules. In
particular:
*Instances of high humidity and moisture increase the risk of electrical short circuits and
potential electrical shocks. If in doubt, disconnect the icemaker.
*Do not damage the power cord or pull it in order to disconnect the icemaker from the
electrical supply network.
*[FM-1000, 600]
If the supply cord and/or the plug should need to be replaced, it should only be done by a
qualied service engineer.
[FM-750, 480, 300, 170]
If the supply cord is damaged, it must be replaced by a replacement cord available from
Hoshizaki Parts/Service Centres.
*Do not touch the electrical parts or operate the switches with damp hands.
*This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, it can however be used
by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge providing they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.
*Children shall not play with the appliance.
*Cleaning and user maintenance shall not be made by children without supervision.
* Do not attempt to modify the icemaker. Only qualied personnel may disassemble or repair
the appliance.

3
ENGLISH
I. INSTALLATION INSTRUCTIONS
1. CONSTRUCTION
2. LOCATION
WARNING
This icemaker is not intended for outdoor use.
The icemaker should not be located next to ovens, grills or other high heat producing equipment.
This appliance is not suitable for installation in an area where a water jet could be used.
CAUTION
The location should provide a rm and level foundation for the icemaker.
NOTICE
Do not place anything on top of the icemaker or in front of the louver.
IMPORTANT
Normal operating ambient temperature should be within 5°C to 40°C. Water connection is cold water only. Operation of the
icemaker, for extended periods, outside of these normal temperature ranges may a󰀨ect production capacity.
Allow the clearance specied below for proper air circulation and ease of maintenance and/or service should they be required.
Top View (FM-600AKE only) Side View
Rear
ICEMAKER
Front
Left Right Rear
Front
Top
ICEMAKER
30cm
15cm
30cm
15cm
60cm
Top View (except FM-600AKE)
Rear
ICEMAKER
Front
Left Right
15cm
15cm
15cm
In some high humidity environments, condensation may form inside the machine and drip onto the oor. Do not install where
the oor can be a󰀨ected by water.
3. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national and local electrical code requirements.
Disconnect the main power supply before any maintenance, repairs or cleaning is undertaken.
* Usually an electrical permit and services of a licensed electrician are required.
Power Supply Cord
Top Panel
Operation Panel
Air Filter
(Air-Cooled Model)
Louver
Front Panel

4
ENGLISH
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter
E or by the symbol or coloured Green or Green-and-Yellow. The wire which is coloured Blue must be connected to the
terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured Red.
* Should the socket outlets in the installation site not be suitable for the plug supplied with your product, the plug must be
removed (cut o󰀨 if it is moulded on plug) and an appropriate plug tted.
If the non-rewirable plug has been cut from the power supply cord, it must be disposed of. There should be no attempt to
reuse it. Inserting such a plug into a socket elsewhere presents a serious risk of electrical shock.
* The non-rewirable plug must never be used without a fuse cover being tted.
The correct replacement for the detachable fuse cover is identiable from the manufacturer’s reference number stamped on
the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki Parts/Service Centres.
Fuses should be rated at 13A and approved to BS 1362.
4. WATER SUPPLY AND DRAIN CONNECTIONS
WARNING
Connect to potable cold water supply only.
* The connections to the mains water supply must be made in accordance with the countries’ current requirements of the Water
Supply or Water Fittings Regulations.
* Icemaking water must be potable water. Where scaling can be caused by water quality, installation of an external lter or
softener is recommended. Contact your local water treatment professional or Hoshizaki service agent.
* A plumbing permit and services of a licensed plumber may be required in some areas.
II. OPERATING INSTRUCTIONS
CAUTION
Do not step into the storage bin, or put your hands into the
machine compartment inside the storage bin. Children can get
trapped inside, or the icemaking mechanism may suddenly
move, resulting in injury.
NOTICE
All parts are factory-adjusted. Improper adjustments may result in failure.
If the unit is turned o󰀨, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor.
Storage Bin

5
ENGLISH
HYGIENE
This icemaker is designed to produce edible ice. To keep the icemaker hygienic:
* Wash your hands before removing ice. Use the plastic scoop provided (accessory).
* The storage bin is for ice use only. Do not store anything else in the bin nor use other electrical appliances in the bin.
* Clean the storage bin before use (see “III. 1. CLEANING”).
* Keep the scoop clean. Clean it by using a neutral cleaner and rinse thoroughly.
* Close the door after removing ice to prevent entrance of dirt, dust or insects into the storage bin.
1. START UP
The installer will normally commission the icemaker to start the
automatic icemaking process. To ensure continuous operation, make
sure that:
* The water supply tap is on, and
* The icemaker is connected to the power supply.
To start the icemaking process, check the position of the operation
switch on the operation panel:
“OFF” position - Move it to the “ON” position.
“ON” position - Press the ice button.
2. SHUT DOWN
Press the stop button on the operation panel. The “STOP” and “DRAIN”
modes light up on the display. Then, only the “DRAIN” mode goes o󰀨.
3. PREPARING THE ICEMAKER FOR LONG STORAGE
NOTICE
This icemaker will not work at subfreezing temperatures. To prevent damage to the water supply line, drain the icemaker when
air temperature is below zero.
HYGIENE
When shutting down the icemaker for two or more days, drain the icemaker to prevent contamination in the water circuit.
1) Follow the instructions in “2. SHUT DOWN”.
2) Close the water supply line shut-o󰀨 valve.
3) Open the drain valve.
4) Press the ice button on the operation panel to drain the water circuit.
5) When no more water comes out of the drain valve, press the stop button.
6) Move the operation switch to the “OFF” position, and disconnect the power supply.
7) Close the drain valve.
8) Remove all ice from the storage bin, and clean the bin.
Operation Panel
Ice Button Display Stop Button
Maintenance Button
(service use only) Operation Switch

6
ENGLISH
III. MAINTENANCE
1. CLEANING
WARNING
Before carrying out any cleaning or maintenance operations, unplug the icemaker from the electrical supply network.
This appliance must not be cleaned by use of a water jet.
CAUTION
When using a neutral cleaner or sodium hypochlorite, thoroughly read and understand the instructions provided to prevent
potential health problems.
NOTICE
Ask a trained service person to clean and sanitise the icemaker water system at least twice a year and to check and clean the
condenser at least once a year.
To prevent possible damage, do not clean the plastic parts with water above 40°C or in a dishwasher.
[a] Machine and Bin Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use a damp cloth containing a neutral cleaner to wipe o󰀨
grease or dirt.
[b] Scoop and Storage Bin Handle Cleaning/Sanitisation (Daily)
1) Either mix 1 litre of water with 4 ml of 5.25% sodium hypochlorite solution in a suitable container, or the recommended
Hoshizaki sanitiser as directed.
2) Soak the scoop in the solution for more than 3 minutes. Rinse thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
3) Use a neutral cleaner to wash the storage bin handle. Rinse thoroughly.
4) Soak a clean cloth with the sanitising solution, and wipe the handle. Use fresh water and a clean cloth to rinse/dry.
[c] Storage Bin Interior Cleaning/Sanitisation (Weekly)
1) Open the storage bin door, and remove all ice.
Note: Hoshizaki recommends various types of storage bin for the icemaker which vary in size and design. The following
instructions are therefore for general guidance only.
2) Remove the thumbscrews securing the ba󰀪e.
3) Remove the ba󰀪e from the bin.
4) Wash the bin liner, and ba󰀪e with a neutral non-abrasive cleaner. Rinse thoroughly.
5) Either mix 5 litres of water with 18 ml of 5.25% sodium hypochlorite solution in a
suitable container, or the recommended Hoshizaki sanitiser as directed.
6) Soak a clean sponge or cloth with the solution, and wipe the bin liner surfaces, and
ba󰀪e.
7) Ret the ba󰀪e and thumbscrews. Wipe the surface of the bin door and thumbscrews
with the solution. Close the bin door.
8) The remaining solution can be used to sanitise utensils.
Note: Do not wipe dry or rinse after sanitising, but allow to air dry.
Thumbscrew
Ba󰀪e

7
ENGLISH
[d] Storage Bin Door
Clean the storage bin door at least once a week, using a neutral non-abrasive cleaner. Rinse thoroughly after cleaning and
sanitise as required.
[e] Air Filter (Air-Cooled Model Only)
Plastic mesh air lters remove dirt or dust from the air, and keep the condenser from getting clogged. If the lters get clogged,
the icemaker’s performance will be reduced. Remove and clean the air lter(s) at least twice per month:
1) Slide the air lter o󰀨 the louver.
2) Clean the air lter by using a vacuum cleaner. When severely clogged, use warm
water and a neutral cleaner to wash the air lter.
3) Rinse and dry the air lter thoroughly.
NOTICE
After cleaning, be sure to place the air lter back in position.
2. INSPECTION AND MAINTENANCE
NOTICE
To achieve optimum icemaker performance, the following parts need periodic inspection and maintenance:
Extruding head (upper bearing)
Housing (lower bearing)
Mechanical seal
[a] Inspection
These parts should be inspected after two years from installation or 10,000 hours of operation, whichever comes rst, and once
a year afterwards. Replacement of these parts is required if wear exceeds factory recommendations.
Their service life, however, depends on water quality and environment. More frequent inspection and maintenance are
recommended in bad or severe water conditions.
Consult with your local Hoshizaki service agent about inspection and maintenance service.
[b] Replacement
The extruding head (upper bearing) and mechanical seal must be replaced after four years from installation or 20,000 hours of
operation, whichever comes rst, to prevent the risk of serious accidents or failures. Contact your local Hoshizaki service agent
for replacement.
When the total operating time reaches 20,000 hours, the display ashes “PC”. Then, after 500 hours, the unit shuts down to
ensure safety. Contact your local Hoshizaki service agent for replacement as soon as the display starts ashing.
Once the unit shuts down after 500 hours, the operation can be resumed by turning o󰀨 the operation switch and turning it back
on. But the unit shuts down again after 500 hours. To resume the operation, contact your local Hoshizaki service agent for the
required replacement.
Replacement of the housing (lower bearing) may be required depending on water quality and wear condition.
3. BEFORE CALLING FOR SERVICE
WARNING
Do not damage the refrigerant circuit.
[a] Error Code Indication
If the error code “E” is indicated on the display, before calling for service, check the following.
Air Filter
Louver

8
ENGLISH
Code Remedy
E0 Possibility of water leaks. Turn OFF operation switch, and turn it ON again. If error code appears again, call for
service.
E1 Low ice production. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
E2 Water supply circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for
service.
E3 Gear motor failure. Turn OFF operation switch, and turn it ON again after 10 minutes. If error code appears again, call
for service.
E4 Abnormal high side pressure. Clean air lter. Check that icemaker is properly installed according to installation manual.
Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
E5 Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
E8 Compressor could be overheated. Check that icemaker is properly installed according to installation manual. Turn OFF
operation switch, and turn it ON again after 10 minutes. If error code appears again, call for service.
EA Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
Eb Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EC Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EE Gear motor failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EF Supply voltage is too low. Check that voltage is in required range and icemaker is not sharing a single receptacle with
other appliances. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EH Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EL Bin control switch has failed. Turn OFF operation switch, and turn it ON again. If error code appears again, call for
service.
En Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EU Controller board failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
[b] No Error Code Indication
If the icemaker does not work properly or does not work at all and no error code is indicated on the display, before calling for
service, check that:
* The power is supplied to the unit.
* The water is turned on.
* The air lter is clean.
For further assistance or advice, contact your local Hoshizaki service agent.
4. DISPOSAL
Comply with local regulations regarding disposal of this appliance and its refrigerant gas. Before you scrap the appliance, take
o󰀨 the door to prevent children trapped.
Correct disposal of this product:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device, use the return and collection
systems or contact the retailer where the product was purchased. They can take this product for environmental safe
recycling.
5. WARRANTY
Hoshizaki warrants to the original owner/user that all Hoshizaki branded products shall be free of defects in material and/or
workmanship for the duration of the “warranty period”. The warranty shall be e󰀨ective for two years from the date of installation.
Hoshizaki’s liability under the terms of the warranty are limited and shall exclude routine servicing, cleaning, essential
maintenance and/or repairs occasioned by misuse and installations not in accordance with Hoshizaki guidelines.

9
ENGLISH
Warranty repairs should be completed by an approved Hoshizaki dealer or service agency using genuine Hoshizaki components.
To obtain full details of your warranty and approved service agency, please contact your dealer/supplier, or the nearest Hoshizaki
Service o󰀩ce:
Europe, Middle East, Africa
Hoshizaki UK - UK, Ireland
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Middle East - Middle East
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Deutschland - Germany, Switzerland, Austria, Poland,
Czech Republic, Slovakia
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Benelux - Netherlands, Belgium, Luxembourg
TEL: [phone]
[email protected]
Hoshizaki France - France
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Italia - Italy
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Iberia - Spain, Portugal
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Europe B.V. - all other countries within Europe
and Africa
TEL: [phone]
FAX: [phone]
[email protected]
Asia, Oceania
Hoshizaki Singapore
TEL: [phone]
FAX: [phone]
[email protected] (Sales)
[email protected] (Technical support)
Hoshizaki Hong Kong
TEL: [phone]
FAX: [phone]
Hoshizaki Taiwan
TEL: [phone]
FAX: [phone]
SPECIFICATIONS
Model FM-1000AKE FM-1000AKE-N
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 2490W 2550W
Ice Production per 24h 1030kg (ambient 10°C, water 10°C) 860kg (ambient 10°C, water 10°C)
Dimensions 762mm(W) x 700mm(D) x 780mm(H) 762mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 1.35kg
(GWP: 3920, CO2: 5.292t)
R404A, 1.35kg
(GWP: 3920, CO2: 5.292t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 146kg (Gross: 156kg) Net: 146kg (Gross: 156kg)
Ambient Temp 5 - 40°C 5 - 40°C

10
ENGLISH
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-750AKE FM-750AKE-N
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1880W 2010W
Ice Production per 24h 750kg (ambient 10°C, water 10°C) 590kg (ambient 10°C, water 10°C)
Dimensions 762mm(W) x 700mm(D) x 780mm(H) 762mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 1.15kg
(GWP: 3920, CO2: 4.508t)
R404A, 1.15kg
(GWP: 3920, CO2: 4.508t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 133kg (Gross: 143kg) Net: 133kg (Gross: 143kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-600AKE FM-600AKE-N
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz / 220-230V 60Hz 1 phase 220-240V 50Hz / 220-230V 60Hz
Electric Consumption 1900W / 2160W 1950W / 2220W
Ice Production per 24h 600kg / 655kg (ambient 10°C, water 10°C) 530kg / 575kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 1.3kg
(GWP: 3920, CO2: 5.096t)
R404A, 1.3kg
(GWP: 3920, CO2: 5.096t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 107kg (Gross: 114kg) Net: 107kg (Gross: 114kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-600AWKE FM-600AWKE-N
Type Water-cooled, ake ice Water-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1705W 1760W
Ice Production per 24h 600kg (ambient 10°C, water 10°C) 490kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 0.7kg
(GWP: 3920, CO2: 2.744t)
R404A, 0.7kg
(GWP: 3920, CO2: 2.744t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 107kg (Gross: 114kg) Net: 107kg (Gross: 114kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%

11
ENGLISH
Model FM-480AKE FM-480AKE-N
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz / 220-230V 60Hz 1 phase 220-240V 50Hz / 220-230V 60Hz
Electric Consumption 1650W / 1590W 1650W / 1590W
Ice Production per 24h 500kg (ambient 10°C, water 10°C) 430kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 0.6kg
(GWP: 3920, CO2: 2.352t)
R404A, 0.6kg
(GWP: 3920, CO2: 2.352t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 95kg (Gross: 102kg) Net: 95kg (Gross: 102kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-480AWKE FM-480AWKE-N
Type Water-cooled, ake ice Water-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1385W 1450W
Ice Production per 24h 420kg (ambient 10°C, water 10°C) 380kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 0.37kg
(GWP: 3920, CO2: 1.450t)
R404A, 0.37kg
(GWP: 3920, CO2: 1.450t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 95kg (Gross: 102kg) Net: 95kg (Gross: 102kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-300AKE FM-300AKE-N
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz / 220-230V 60Hz 1 phase 220-240V 50Hz / 220-230V 60Hz
Electric Consumption 1000W / 1180W 1000W / 1200W
Ice Production per 24h 320kg / 340kg (ambient 10°C, water 10°C) 270kg / 290kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R404A, 0.46kg
(GWP: 3920, CO2: 1.803t)
R404A, 0.46kg
(GWP: 3920, CO2: 1.803t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 80kg (Gross: 87kg) Net: 80kg (Gross: 87kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%

12
ENGLISH
Model FM-170AKE FM-170AKE-N
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz / 220-230V 60Hz 1 phase 220-240V 50Hz / 220-230V 60Hz
Electric Consumption 600W / 675W 620W / 695W
Ice Production per 24h 170kg / 180kg (ambient 10°C, water 10°C) 160kg / 165kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R134a, 0.37kg
(GWP: 1430, CO2: 0.529t)
R134a, 0.37kg
(GWP: 1430, CO2: 0.529t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 68kg (Gross: 75kg) Net: 68kg (Gross: 75kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-1000AKE-R452-SB FM-1000AKE-R452N-SB
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 2490W 2550W
Ice Production per 24h 1030kg (ambient 10°C, water 10°C) 860kg (ambient 10°C, water 10°C)
Dimensions 762mm(W) x 700mm(D) x 780mm(H) 762mm(W) x 700mm(D) x 780mm(H)
Refrigerant R452A, 1.35kg
(GWP: 1945, CO2: 2.626t)
R452A, 1.35kg
(GWP: 1945, CO2: 2.626t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 146kg (Gross: 156kg) Net: 146kg (Gross: 156kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-750AKE-R452-SB FM-750AKE-R452N-SB
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1880W 2010W
Ice Production per 24h 750kg (ambient 10°C, water 10°C) 590kg (ambient 10°C, water 10°C)
Dimensions 762mm(W) x 700mm(D) x 780mm(H) 762mm(W) x 700mm(D) x 780mm(H)
Refrigerant R452A, 1.15kg
(GWP: 1945, CO2: 2.237t)
R452A, 1.15kg
(GWP: 1945, CO2: 2.237t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 133kg (Gross: 143kg) Net: 133kg (Gross: 143kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%

13
ENGLISH
Model FM-600AKE-R452-SB FM-600AKE-R452N-SB
Type Air-cooled, ake ice Air-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1900W 1950W
Ice Production per 24h 600kg (ambient 10°C, water 10°C) 530kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R452A, 1.3kg
(GWP: 1945, CO2: 2.529t)
R452A, 1.3kg
(GWP: 1945, CO2: 2.529t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 107kg (Gross: 114kg) Net: 107kg (Gross: 114kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-600AWKE-R452-SB FM-600AWKE-R452N-SB
Type Water-cooled, ake ice Water-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1705W 1760W
Ice Production per 24h 570kg (ambient 10°C, water 10°C) 490kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R452A, 0.7kg
(GWP: 1945, CO2: 1.362t)
R452A, 0.7kg
(GWP: 1945, CO2: 1.362t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 107kg (Gross: 114kg) Net: 107kg (Gross: 114kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Model FM-480AWKE-R452-SB FM-480AWKE-R452N-SB
Type Water-cooled, ake ice Water-cooled, nugget ice
Power Supply 1 phase 220-240V 50Hz 1 phase 220-240V 50Hz
Electric Consumption 1385W 1450W
Ice Production per 24h 420kg (ambient 10°C, water 10°C) 380kg (ambient 10°C, water 10°C)
Dimensions 560mm(W) x 700mm(D) x 780mm(H) 560mm(W) x 700mm(D) x 780mm(H)
Refrigerant R452A, 0.37kg
(GWP: 1945, CO2: 0.720t)
R452A, 0.37kg
(GWP: 1945, CO2: 0.720t)
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 95kg (Gross: 102kg) Net: 95kg (Gross: 102kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.8 MPa (0.5 - 8 bar) 0.05 - 0.8 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 10% Rated voltage ± 10%
Note: The above specications are for the representative models.
This product includes a hermetically sealed refrigeration system that contains uorinated greenhouse gases.

14
FRANCAIS
INFORMATIONS DE SECURITE IMPORTANTES
Tout au long de ce manuel, des avis attirent votre attention sur des situations qui pourraient
entraîner la mort, des blessures graves ou des dégâts à l’appareil.
AVERTISSEMENT Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des blessures graves voire mortelles.
ATTENTION Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des blessures mineures ou modérées.
AVIS Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des dégâts à l’appareil.
HYGIENE Signale des précautions importantes à prendre en matière d’hygiène
et de sécurité alimentaire.
IMPORTANT Signale des informations importantes sur l’utilisation de l’appareil et
son entretien.
IMPORTANT
Ce livret est un élément essentiel qui fait partie intégrante du produit et il doit être conservé
soigneusement par l’utilisateur.
Veuillez lire attentivement les conseils et avertissements qu’il contient car ils ont pour but
de fournir à l’utilisateur des informations essentielles pour la bonne utilisation et l’entretien
correct du produit. En outre, il fournit à l’utilisateur des INDICATIONS sur les utilisations et les
emplacements corrects de la machine à glace.
Veuillez conserver précieusement ce livret pour toute référence ultérieure.
AVERTISSEMENT
Cette machine à glace a été conçue pour des applications commerciales ; elle ne peut être
utilisée qu’aux fins auxquelles elle est expressément destinée, et fournie avec un bac de
stockage adapté tel que spécié par Hoshizaki.
Toute autre utilisation doit être considérée comme inappropriée et donc dangereuse.
Le fabricant décline toute responsabilité pour les dégâts provoqués par une utilisation
inappropriée, incorrecte et abusive.
L’installation, et le transfert le cas échéant, doivent être effectués par un personnel
qualié, conformément aux réglementations en vigueur et aux consignes du fabricant.
Veillez à ce que les ouvertures de ventilation de l’enceinte de l’appareil et de la structure
intégrée ne soient pas obstruées.

15
FRANCAIS
L’utilisation de tout appareil électrique implique le respect de certaines règles fondamentales.
En particulier :
*En cas de forte humidité, les risques de court-circuit et d’électrocution augmentent. En cas
de doute, débrancher la machine à glace.
*Ne pas endommager le cordon d’alimentation et ne pas tirer sur le cordon d’alimentation pour
débrancher la machine à glace.
*[FM-1000, 600]
Si le cordon et/ou la fiche d’alimentation électrique sont à remplacer, l’opération doit être
e󰀨ectuée par un technicien qualié.
[FM-750, 480, 300, 170]
Si le cordon d’alimentation est endommagé, il doit être remplacé par un cordon de rechange
disponible auprès des centres de pièces détachées et d’entretien Hoshizaki.
*Ne pas toucher les pièces électriques ou les commutateurs avec les mains humides.
*Cette machine n’est pas prévue pour une utilisation par des personnes (y compris des
enfants) aux capacités physiques, sensorielles ou mentales réduites, ou manquant
d’expérience ou de connaissances. Elle peut cependant être utilisée par des enfants d’au
moins 8 ans et des personnes aux capacités physiques, sensorielles ou mentales réduites,
ou manquant d’expérience ou de connaissances, si une personne responsable de leur
sécurité les surveille ou leur a indiqué les consignes d’utilisation de la machine.
*Les enfants ne doivent pas jouer avec la machine.
*Le nettoyage et l’entretien régulier ne doivent pas être effectués par des enfants sans
surveillance.
* Ne pas tenter de modier la machine à glace. Cet appareil ne peut être démonté ou réparé
que par du personnel qualié.

16
FRANCAIS
I. CONSIGNES D’INSTALLATION
1. CONSTRUCTION
2. EMPLACEMENT
AVERTISSEMENT
Cette machine à glace n’est pas conçue pour être utilisée à l’extérieur.
La machine à glace ne doit pas être placée à proximité de fours, de grills ou de toute autre source de chaleur importante.
Cet appareil n’est pas conçu pour être installé dans une zone où un jet d’eau peut être utilisé.
ATTENTION
La machine à glace doit avoir une assise solide et horizontale.
AVIS
Ne rien poser sur le dessus de la machine ni devant le volet d’aération.
IMPORTANT
La température ambiante normale de service doit être comprise entre 5 °C et 40 °C. Le raccordement à l’eau est uniquement
pour de l’eau froide. Le fonctionnement de la machine en dehors de ces plages de températures, pendant des durées
prolongées, risque d’a󰀨ecter la capacité de production de glaçons.
Pour assurer une bonne circulation d’air et faciliter les opérations de maintenance ou d’entretien, prévoir le dégagement
indiqué ci-dessous.
30 cm
15 cm
30 cm
15 cm
60 cm
15 cm
15 cm
15 cm
Vue du dessus (sauf FM-600AKE) Vue du dessus (FM-600AKE uniquement) Vue latérale
Arrière
Gauche
Droite Droite
Gauche
Avant
Arrière
Avant
Avant
Arrière
Haut
MACHINE A GLACEMACHINE A GLACE MACHINE
A GLACE
Dans certains environnements très humides, de la condensation peut se former à l’intérieur de la machine et couler sur le sol.
Ne pas installer l’appareil sur un sol que l’eau pourrait endommager.
3. BRANCHEMENTS ELECTRIQUES
AVERTISSEMENT
CET APPAREIL DOIT ETRE MIS A LA TERRE
Cette machine à glace doit avoir une mise à la terre qui respecte les réglementations électriques nationales et locales.
Avant toute opération de maintenance, réparation ou nettoyage, débrancher l’alimentation électrique.
Panneau de
commande
Cordon d’alimentation
Panneau supérieur
Filtre à air
(modèles refroidis par air)
Volet
d’aération
Panneau avant

17
FRANCAIS
* En général, l’installation nécessite une autorisation pour travaux électriques et les services d’un électricien qualié.
Pour le Royaume-Uni et la République d’Irlande uniquement
* Les ls du cordon d’alimentation électrique présentent le codage couleur suivant :
Vert et Jaune = Terre
Bleu = Neutre
Marron = Sous tension
La couleur des conducteurs du cordon d’alimentation de cet appareil peut ne pas correspondre au marquage couleur des
bornes de votre che ; dans ce cas, procéder comme suit :
Le l vert et jaune doit être relié à la borne de la che repérée par la lettre E ou par le symbole ou la couleur verte ou
verte et jaune. Le conducteur bleu doit être raccordé à la borne portant la lettre N ou de couleur noire. Le conducteur marron
doit être raccordé à la borne portant la lettre L ou de couleur rouge.
* Si la che livrée avec la machine ne convient pas aux prises du local d’installation, l’enlever (la couper s’il s’agit d’une che
moulée) et en monter une autre.
Une che non recâblable enlevée doit être jetée. Elle ne peut en aucun cas être réutilisée. L’insertion de ce type de che
dans une autre prise présente des risques graves de décharges électriques.
* La che non recâblable ne doit jamais être utilisée sans un protège-fusible.
Le numéro de référence du protège-fusible amovible est imprimé sur la che. Utiliser cette référence pour toute commande
de pièce.
Il est possible de se procurer des protège-fusibles de remplacement auprès des centres de pièces détachées et d’entretien
Hoshizaki.
La capacité nominale des fusibles doit être de 13 A ; ils doivent être agréés selon la norme BS 1362.
4. BRANCHEMENTS D’ARRIVEE ET DE VIDANGE D’EAU
AVERTISSEMENT
Raccorder à l’arrivée d’eau potable froide uniquement.
* Les raccordements à l’alimentation en eau du réseau doivent être réalisés conformément aux exigences nationales en vigueur
des réglementations sur l’alimentation en eau ou les raccords.
* L’eau utilisée pour la fabrication de la glace doit être potable. Là où la qualité de l’eau peut entraîner la formation de calcaire,
l’installation d’un ltre externe ou d’un adoucisseur est recommandée. Contactez le professionnel du traitement de l’eau ou
l’agent de service Hoshizaki local.
* Dans certaines régions, il est possible qu’il faille obtenir une autorisation pour e󰀨ectuer les travaux de plomberie et avoir
recours aux services d’un plombier autorisé.
II. CONSIGNES D’UTILISATION
ATTENTION
Ne pas marcher dans le bac de stockage ni mettre ses mains
dans le compartiment de la machine situé à l’intérieur. Les
enfants pourraient s’y retrouver coincés, ou le mécanisme de
fabrication de glace se mettre en marche accidentellement,
entraînant des risques de blessures.
Bac de stockage