HP E3473A User manual

A
Dear Customer:
You have probably heard from news reports and from your sales representative that
as of November 1, 1999, four of Hewlett-Packard's businesses became a new
company -- Agilent Technologies. The new company includes the following former
HP businesses: test and measurement, semiconductor products, healthcare
solutions and chemical analysis."
We at Agilent Technologies are working diligently to make this transition as
seamless as possible for you, however, we are not able to make all changes
immediately. As a result, the products and related documentation may be labeled
with either the Hewlett-Packard name and logo or the Agilent Technologies name
and logo. Rest assured that whatever logo you see, the information, products and
services come from the same reliable source.
In addition, it is our sincere intent that the transition from Hewlett Packard to
Agilent Technologies should have no impact on your warranties, service levels, or
purchase volume credits.
For more information about this transition, please visit our website at:
http://www.agilent.com, or contact your local sales representative. It has been our
pleasure to work with you for the past 60 years as part of Hewlett-Packard. We look
forward to continuing to serve you as Agilent Technologies for years to come.

User’s Guide
Publication number E3472-97001
Second edition, March 1997
For Safety information, Warranties, and Regulatory information, see the
pages preceding the table of contents.
© Copyright Hewlett-Packard Company 1997
All Rights Reserved
HP E3472A/73A Emulator
for SH7040/50

Notice
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard
shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or
use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
© Copyright 1997, Hewlett-Packard Company.
This document contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the prior
written consent of Hewlett-Packard Company. The information contained in
this document is subject to change without notice.
HP is a trademark of Hewlett-Packard Company.
IBM is a trademark of International Business Machines Corporation.
MS-DOSis a U.S. registered trademark of Microsoft Corp.
UNIXis a registered trademark in the United States and other countries,
licensed exclusively through X/Open Company Limited.
Windowsand MS windowsare U.S. registered trademarks of Microsoft
Corp.
Sun is a trademark or a registrered trademark of Sun Microsystems, Inc. in
the United States and other countries.
All the SPARC trademarks are trademarks or registered trademarks in the
United States and other countries, licensed exclusively through SPARC
international, Inc.
Hewlett-Packard
P.O. Box 2197
1900 Garden of the Gods Road
Colorado Springs, CO 80901-2197, U.S.A.
RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by
the U.S. Government is subject to restrictions as set forth in
subparagraph (c) (1)(ii) of the Rights in Technical Data and Computer
Software Clause at DFARS 252.227-7013. Hewlett-Packard Company,
3000 Hannover Street, Palo Alto, CA 94304 U.S.A. Rights for non-DOD
U.S. Government Departments and Agencies are as set forth in FAR
52.227-19(c)(1,2).

Printing History
New editions are complete revisions of the manual. The date on the title
page changes only when a new edition is published.
A software code may be printed before the date; this indicates the version
level of the software product at the time the manual was issued. Many
product updates and fixes do not require manual changes, and manual
corrections may be done without accompanying product changes. Therefore,
do not expect a one-to-one correspondence between product updates and
manual revisions.
Edition 1
E3472-97000, Oct. 1996
Edition 2
E3472-97001, Mar. 1997
iii

Certification
Hewlett-Packard Company certifies that this product met its published
specifications at the time of shipment from the factory. Hewlett-Packard
further certifies that its calibration measurements are traceable to the United
States National Institute of Standards and Technology, to the extent allowed
by the Institution’s calibration facility, or to the calibration facilities of other
International Standards Organization members.
Warranty
This Hewlett-Packard instrument product is warranted against defects in
material and workmanship for a period of one year from the date of shipment,
except that in the case of certain components listed in General Information
of this manual, the warranty shall be for the specified period. During the
warranty period, Hewlett-Packard Company will, at its option, either repair or
replace products that prove to be defective.
For warranty service or repair, this product must be returned to a service
facility designated by HP. Buyer shall prepay shipping charges to HP and HP
shall pay shipping charges to return the product to Buyer. However, Buyer
shall pay all shipping charges, duties, and taxes for products returned to HP
from another country.
HP warrants that its software and firmware designated by HP for use with an
instrument will execute its programming instruction when property installed
on that instrument. HP does not warrant that the operation of the
instrument, or software, or firmware will be uninterrupted or error free.
Limitation Of Warranty
The foregoing warranty shall not apply to defects resulting from improper or
inadequate maintenance by Buyer, Buyer-supplied software or interfacing,
unauthorized modification or misuse, operation outside the environmental
specifications for the product, or improper site preparation or maintenance.
No other warranty is expressed or implied. HP specifically disclaims
the implied warranties of merchantability and fitness for a particular
purpose.
iv

Exclusive Remedies
The remedies provided herein are buyer’s sole and exclusive remedies.
HP shall not be liable for any direct, indirect, special, incidental, or
consequential damages, whether based on contract, tort, or any other
legal theory.
Assistance
Product maintenance agreements and other customer assistance agreements
are available for Hewlett-Packard products.
For any assistance, contact your nearest Hewlett-Packard Sales and Service
Office. Addresses are provided at the back of this manual.
v

Safety Summary
The following general safety precautions must be observed during all phases
of operation, service, and repair of this instrument. Failure to comply with
these precautions or with specific WARNINGS elsewhere in this manual may
impair the protection provided by the equipment. In addition it violates safety
standards of design, manufacture, and intended use of the instrument.
The Hewlett-Packard Company assumes no liability for the customer’s
failure to comply with these requirements.
Note The HP E3472A/73A complies with INSTALLATION CATEGORY I and
POLLUTION DEGREE 2 in IEC1010-1. The HP E3472A/73A is INDOOR USE
product.
Note LEDs in this product are Class 1 in accordance with IEC825-1.
CLASS 1 LED PRODUCT
Ground The Instrument
To avoid electric shock hazard, the AC/DC adapter must be connected to a
safety earth ground by the supplied power cable with earth blade.
DO NOT Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of flammable gasses or fumes.
Operation of any electrical instrument in such an environment constitutes a
safety hazard.
Keep Away From Live Circuits
Operating personnel must not remove instrument covers. Component
replacement and internal adjustments must be made by qualified
maintenance personnel. Do not replace components with the power cable
connected. Under certain conditions, dangerous voltages may exist even
with the power cable removed. To avoid injuries, always disconnect power
and discharge circuits before touching them.
DO NOT Service or Adjust Alone
Do not attempt internal service or adjustment unless another person, capable
of rendering first aid and resuscitation, is present.
DO NOT Substitute Parts or Modify Instrument
Because of the danger of introducing additional hazards, do not install
substitute parts or perform unauthorized modifications to the instrument.
Return the instrument to a Hewlett-Packard Sales and Service Office for
service and repair to ensure that safety features are maintained.
vi

Dangerous Procedure Warnings
Warnings, such as the example below, precede potentially dangerous
procedures throughout this manual. Instructions contained in the warnings
must be followed.
Warning Dangerous voltages, capable of causing death, are present in this instrument.
Use extreme caution when handling, testing, and adjusting this instrument.
Power Requirements
The HP E3472A/73A requires the following power source:
Voltage : 90 to 132 Vac, 198 to 264 Vac
Frequency : 47 to 63 Hz
Power : 300 VA maximum
Power Cable
In accordance with international safety standards, this instrument is
equipped with a three-wire power cable. When connected to an appropriate
ac power outlet, this cable grounds the instrument frame.
The type of power cable shipped with each instrument depends on the
country of destination. Refer to Figure 1 for the part numbers of the power
cables available.
Warning
For protection from electrical shock, the power cable ground must no be
defeated.
The power plug must be plugged into an outlet that provides a protective
earth ground connection.
vii

Figure 1. Power CordsAvailable for Each Destination
viii

Safety Symbols
General definitions of safety symbols used on equipment or in manuals are
listed below.
Instruction manual symbol: the product is marked with this symbol when it is
necessary for the user to refer to the instruction manual.
Alternating current.
Direct current.
On(Supply).
Off(Supply).
Warning This warning sign denotes a hazard. If calls attention to a procedure,
practice, condition or the like, which, if not correctly performed or adhered
to, could result in injury or death to personnel.
Caution This caution sign denotes a hazard. If calls attention to a procedure,
practice, condition or the like, which, if not correctly performed or adhered
to, could result in damage to or destruction of part or all of the product.
Note This note sign denotes important information. If calls attention to a
procedure, practice, condition or the like, which is essential to highlight.
ix

Outline of this manual
Chapter 1 describes the product overview and its outer features.
Chapter 2 lists the contents of the product.
Chapter 3 shows you how to assemble the Emulator and install memory
modules.
Chapter 4 shows you how to configure LAN parameters to connect the
Emulator to the host computer.
Chapter 5 shows you how to connect the Emulator to your target system.
Chapter 6 describes instructions in designing target system.
Chapter 7 shows you how to use the Emulator with a logic analyzer
connected.
Chapter 8 describes the specifications and characteristics of the product.
Chapter 9 shows you how to update the firmware of the Emulator.
Chapter 10 shows you, if a problem occurs when working with the Emulator,
how to isolate its causes.
Appendix A lists the register classes available with the Emulator.
x

Contents
1 Product Overview
Emulator Components 3
Emulation controller 3
Emulation probe 5
Usage - Quick Guide 6
The target connection 6
The host computer connection 6
The configuration switches 6
The status LEDs 6
2 Contents of HP E3472A/73A
Incoming Inspection 9
Instruction for Cleaning 12
Ventilation Requirements 12
3 Setting up the Emulator
Procedure 15
To connect the power cord and turn on the HP E3472A/73A Emulator 16
To test the HP E3472A/73A Emulator 17
Installing the Emulation Memory Module 17
4 Connecting to the Host Computer
Setting Up a LAN Connection 21
To obtain an IP address 22
To configure LAN parameters using the built-in terminal interface 23
To configure LAN parameters using "ipconfig700" 26
To configure LAN parameters using BOOTP 29
To set the 10BASE-T configuration switches 32
To verify LAN communications 33
Setting Up a Serial Connection 34
xi

To set the serial configuration switches 35
To connect a serial cable 36
To verify serial communications 37
5 Connecting to the Target System
QFP cable 41
QFP socket/adapter 41
Connecting the HP E3472A/73A Emulator to the target system 42
6 Designing a Target System
QFP socket/adapter 47
Pin relationship between 177-pin connector and QFP socket/adapter 48
Target interface 48
Cautions in designing target systems 48
7 Using the Logic Analyzer
Connecting the Logic Analyzer 51
To verify the connection 53
Restrictions 54
8 Specifications and Characteristics
Processor compatibility 59
Supported Logic Analyzers 60
Target System Requirements 61
Target Interface (HP E3472A) 62
Target Interface (HP E3473A) 64
Electrical Specifications 79
Environmental Specifications 89
Regulatory Compliance 89
9 Updating Firmware
Components of the software updates 93
Setting up the Host Software 94
To set up the 64700tab.net file 94
Contents
xii

To set up the 64700tab file 95
To update firmware with "progflash" 96
To display current firmware version information 98
If the firmware doesn’t appear to be updated 98
If there is a power failure during a firmware update 98
10 Solving Problems
Status Lights 101
Problems with the LAN Interface 103
If you cannot verify LAN communication 103
If you have LAN connection problems 104
If it takes a long time to connect to the network 106
Problems with the Serial Interface 107
If you cannot verify RS-232 communication 107
Problems with the HP E3472A/73A Emulator Itself 108
To execute the built-in performance verification test 108
If the data in ROM is corrupt 115
Note 116
A Registers List
HP E3472A 2
HP E3473A 10
Index
Contents
xiii

Contents
xiv

1
Product Overview
Product Overview
1

Product Overview
The HP E3472A/73A Emulator provides distributed emulation environment
for the Hitachi SH7040/50 Series processors. Depending on size and
requirements of your development, you can use it either as a simple emulator
working standalone, or as a powerful debugging environment by connecting
it to a logic analyzer.
Hooking up the HP E3472A/73A Emulator to an HP’s logic analyzer enables
high-speed real-time tracing. You can control the emulator and logic analyzer
through the HP E3755A/56A Debug User Interface, allowing you to operate
the emulation environment with a feel similar to conventional debuggers.
Figure 1-1. Distributed Emulation Environment with HP E3472A/73A
Product Overview
2

Emulator Components
Emulation controller
1. TRIGGER OUT connector Sends out the trigger signal.
2. BREAK IN connector Receives the trigger signal from the logic
analyzer.
3. 50-pin connector Connected to the emulation probe through the
50-pin flat cable.
4. Status LEDs Indicate the operating status of the emulation
controller.
5. Auxiliary power connector Supplies power to the emulation probe.
Product Overview
Emulation controller
3

1. Power connector Connects the power cable.
Connecting/disconnecting the power cable will
switch ON/OFF the emulator.
2. DIP switches Configure the settings of the Emulator.
Instructions are printed on the bottom of the
emulation controller.
3. RS-232 connector Connects the RS-232 cable to communicate with
the host computer via the serial connection.
4. LAN status LEDs Indicate the communication status of the
Emulator working on the LAN.
5. LAN connector (10BASE-T) Connects the LAN cable when the Emulator
communicates with the host computer via
10BASE-T LAN.
6. LAN connector (10BASE2) Connects the LAN cable when the Emulator
communicates with the host computer via
10BASE2 LAN.
Product Overview
Emulationcontroller
4

Emulation probe
1. PGA connector Connects to the QFP socket/adapter seated on
the target system.
2. Power LED Indicates that power is supplied to the emulation
probe.
3. Power connector Connects the auxiliary power cable from the
emulation controller.
4. 50-pin connector Connected to the emulation controller through
the 50-pin flat cable.
5. Pod connector Connects the pods of the logic analyzer.
Product Overview
Emulation probe
5