HP Invent XW6200 User manual

SATA Hard Drive
Installation Guide
SATAハー ド デ ィ スク ドライブ
インストール ガイド
Document Part Number: 345524-B21
August 2003
This document provides instructions on installing a serial
advanced technology attachment (SATA) hard drive into your
computer.
このマニュアルでは、コンピュータにSerial ATA（SATA）ハードディ
スク ドライブを取り付 る方法について説明します。
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com
all-guides.com

345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

1
Preparing for Installation
Although HP computers are designed for easy access to the
upgradeable areas, it is strongly recommended that only an HP
authorized dealer, reseller, or service provider install accessories.
HP authorized dealers, resellers, and service providers are
company trained in the installation of accessories and can ensure
that the accessory is installed and functioning properly.
f you decide to install the hard drive accessory yourself, you will
need a Torx T-15 screwdriver.
For additional information on SATA
technology, consult the white paper
“Implementation of Serial ATA on HP
Business Desktops” available at
http://www.hp.com/support.
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Preparing for Installation
1–2 SATA Hard Drive Installation Guide
Disassembling the Computer
1. Turn off the computer and any external devices.
2. Disconnect the AC power cord and any external devices.
3. Unlock the external chassis keylock (if applicable).
4. f necessary, loosen the screws on the computer to remove
the access panel or computer cover.
5. Remove the access panel or computer cover and front bezel.
Refer to the documentation that came with your computer
for model specific instructions on accessing the inside of the
computer.
ÄCAUTION: Ensure that the power to the computer is off
and the AC power cord disconnected to avoid electrical
shock or damage to the computer.
HP accessories are for use in HP computer
products. They have been extensively tested for
reliability and are manufactured to high quality
standards. HP warrants only those accessories that
are manufactured or sold by HP.
345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

2
Installing a Hard Drive
This chapter covers:
Qnstalling an additional hard drive.
QReplacing an existing hard drive.
If you are installing a SATA hard drive on an
hp workstation xw series, please refer to
www.hp.com/go/bizsupport for
workstation-specific installation information.
This information may be in the form of a SATA
whitepaper and/or embedded in the service
and technical reference guide
(www.hp.com/support/workstation_manuals)
for your specific workstation.
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
2–2 SATA Hard Drive Installation Guide
It is strongly recommended that only an HP
authorized dealer, reseller, or service
provider replace your primary hard drive.
ÅWARNING: To reduce the risk of personal
injury from hot surfaces, allow the internal
system components to cool before touching.
ÄCAUTION: Ensure that the power to the computer
is off. Disconnect the AC power cord to avoid
electrical damage to the computer. Electrostatic
discharge (ESD) can damage electronic
components. Be sure you are properly grounded
before beginning this procedure. Refer to
Appendix A, “Electrostatic Discharge,” for more
information.
Refer to the documentation that came with your
computer for detailed instructions on installing an
optional drive.
345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com
all-guides.com

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–3
Installing an Additional Hard
Drive
1. f your system uses guide screws to hold the drives in the
bay, install the screws on the hard drive. These guide screws
are stored behind the front bezel.
345524-B21.book 3 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
2–4 SATA Hard Drive Installation Guide
2. nstall the hard drive assembly by sliding it into the drive
bay as shown in the illustration below.
For comprehensive instructions on installing an
additional hard drive, refer to the documentation
that came with your computer.
345524-B21.book 4 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–5
3. Locate the appropriate connectors, identified in the
following illustration, on the back of the SATA hard drive.
Hard Drive Connectors
1SATA power connector
2SATA data connector
3Debugging connector
4Legacy power connector (not present on all models)
345524-B21.book 5 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
2–6 SATA Hard Drive Installation Guide
4. Connect the data cable to the SATA data connector on the
new drive as shown in the following illustration.
Five data cables are provided in the kit. Refer
to the “SATA Hard Drive Cables” card
included in the kit to determine which cable
is required for your system board.
ÄCAUTION: The data cable end is keyed to
ensure proper alignment. To avoid damage
to the cable header pins, check the
header/connector alignment and push
gently when connecting the data cable
header to the SATA connector on the drive
and system board.
345524-B21.book ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–7
345524-B21.book 7 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com
all-guides.com

Installing a Hard Drive
2–8 SATA Hard Drive Installation Guide
5. Connect the power cable to the SATA power connector as
shown in the illustration below.
345524-B21.book 8 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–9
6. Connect the opposite end of the SATA data cable to the
system board as shown in the following illustration. Because
system boards vary, your system board may contain up to
two vertical SATA connectors 1 or up to two horizontal
SATA connectors 2. Horizontal SATA connectors require a
data cable with a 90 degree angled header.
ÄCAUTION: For SATA hard drives use the
SATA or legacy power connector. Do not
plug in both.
345524-B21.book 9 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
2–10 SATA Hard Drive Installation Guide
345524-B21.book 10 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–11
Replacing an Existing Hard Drive
ÄCAUTION: If your system has only one
SATA hard drive, you must connect the hard
drive to the connector labeled SATA 0 first to
avoid any hard drive performance problems.
ÄCAUTION: Prior to replacing an existing
hard drive, be sure to back up your data. If
your computer supports only one hard drive,
you must use a second system with third-party
software to copy the data to the new hard
drive.
345524-B21.book 11 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
2–12 SATA Hard Drive Installation Guide
HP strongly recommends that only an HP
authorized dealer, reseller, or service
provider replace your primary hard drive.
However, if you choose to perform a
self-install, follow the steps in the previous
section, “Installing an Additional Hard
Drive.” You may also refer to the technical or
service-related documentation applicable to
your computer for more comprehensive
instructions.
345524-B21.book 12 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com
all-guides.com

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–13
Reassembling the Computer
1. Replace the front bezel.
2. Replace the computer cover or access panel and tighten the
screws. (if applicable)
3. Lock the external chassis keylock (if applicable).
4. Reconnect any external devices to the computer.
5. Plug the AC power cord into the computer, then into a
grounded AC outlet.
ÅWARNING: This equipment is designed for
connection to a grounded (earthed) outlet.
The ground type plug is an important safety
feature. To avoid the risk of electric shock or
damage to your equipment, do not disable
this feature.
If you need additional assistance, refer to the
documentation that came with your computer for
product-specific information about reassembling
the computer.
345524-B21.book 13 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Installing a Hard Drive
2–14 SATA Hard Drive Installation Guide
345524-B21.book 14 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

3
Configuring the Computer
System configuration is the process of specifying the devices and
programs that make up a computer system. When you add or
remove accessories, the computer must be reconfigured to
recognize these changes.
The information in this chapter is only applicable if you
installed an additional (second) drive. If you just
upgraded your existing hard drive and transferred your
data from an old drive to the new drive, you may skip
the procedures on drive partitioning unless you
encounter problems upon start up.
If you are installing a SATA drive in your computer for
the first time, you must refer to the white paper
“Implementation of Serial ATA on HP Business Desktops”
for operating system instructions. The white paper is
located at http://www.hp.com/support.
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com

Configuring the Computer
SATA Hard Drive Installation Guide 3–2
Turn on your computer and read the messages that appear during
startup.
Qf the system recognizes the new drive, information about
the drive displays on the screen and you are prompted to
press F1 to save and continue.
Qf you are not prompted to press F1, there is a problem with
the installation of the drive, and you need to diagnose the
problem. Start by reviewing the steps in this guide.
Creating a Partition Using Microsoft
Windows 2000
To create a partition for the additional drive using Microsoft
Windows 2000:
1. Log in as Administrator.
2. From the Windows desktop click Start > Settings > Control
Panel.
3. Click Administrative Tools.
4. Click Computer Management.
5. Click Storage.
345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分
All manuals and user guides at all-guides.com