HP HP34401A User manual

GEORGIA INSTITUTE OF TECHNOLOGY
User’s Guide
HP34401A
Digital Multimeter
Brian Brown

Table of Contents
Introduction 1
Features 1
Specifications 1
SECTION 1
Setting Up the HP34401A 2
Overview of the Controls 2
SECTION 2
How To Measure DC/AC Voltage 3
How To Measure DC/AC Current 4
How To Measure Resistance 5
How To Measure Frequency 5
SECTION 3
Trouble Shooting 6
Where to Find More Help 6
References 6

GETTING STARTED
1
Introduction to the
HP34401A Digital Multimeter
The following is a brief overview of the DMM.
his manual was written to instruct ECE 3041 students on the operation and uses of
the HP34401A Digital Mulitmeter. The HP34401A is a very versatile instrument
capable of measuring numerous circuit characteristics. It is capable of measuring
electric characteristics such as: voltage, current, frequency and resistance with very
high accuracy. These functions will be the focus of this manual. The following guide is for
course-specific applications and not intended to be used as a complete user’s manual. Tofind
more information beyond the scope of this manual, check the “Where to Find More Help”
section.
Features
he HP34401A is setup for bench-topusewith ACpowersupply. It performs at 1000
readings/sec and has a 6½-digit display. The HP34401Awillautomaticallyadjustthe
range to the characteristic being measured. It is also extremely accurate: 0.0015%
error for DC, 0.06% for AC.
Specifications
Function Range
(For accuracy specifications, consult the full manual)
DC Characteristics:
DC Voltage Range and input Resistances:
0.1V, 1V, 10V: input resistance selectable 10MW or > 10GW
100mV to 1000V: Rin = 10MW
DC Current range and shunt resistance:
10mA, 100mA: Rshunt= 5 W
1A and 3A: 0.1 W
AC Characteristics: true RMS: AC Voltage: from 3 Hz to 300 kHz
AC Current from 3 Hz to 5 kHz
Resistance range: 2-wireand4-wire
method:
100 W, 1 kW, 10 kW, 100 kW, 1 MW and 100 MW
Input protection: 1000V
Frequency and Period measurement: Frequency range: 3 Hz -300 kHz
Input voltage range: 100 mV to 750 V
T
T
Table 1. Table of Function Ranges [1]

GETTING STARTED
2
Setting Up the HP34401A
1. Get all lab supplies ready for use.
q HP34401A Digital Multimeter
q Probes Leads (found hanging in wall racks)
q Alligator Clips for Lead ends
q Breadboard and circuit components (if needed)
2. Turn on the Multimeter.
The front panel display will light up while the meter performs the power-on self–test. After
this is complete, the HP34401A is ready to perform measurements.
Overview of Controls
The front panel has two rows of keys for selecting the functions. The right side of the panel
contains various probe input locations of which the selection is dependent upon the
characteristic being measure (Figure 1). The selection keys are annotated in black and blue. To
select a function in blue, first select the blue SHIFT key.
Section
1
Function Button Panel: DC V or I
, AC V or
I, Resistance (ohm’s) and Freq
Probe Input Panel
Power
Button
Figure 1. Overview of front panel [1]

TAKING MEASUREMENTS
3
Figure 3. Probe/Meter placement
on the circuit to Measure Voltage
Across Resistor R
Circuit under Test
Hi
+DMM
V
-
Lo
V
How to Measure DC and AC
Voltage
To measure a voltage, connect the probes to the HI andLO input terminalsoftheDMM. In
order to activate the DMM for voltage measurements, select either the AC V orDCV button
on the front panel (Figure 2).
Next, connect the leads of the probes to
the circuit in parallel with the location of
the voltage in question (Figure 3). The
Hi lead connects to the “+” (pos) part of
the circuit and the Lo tothe “–“ (neg). If
these are reversed, a negative value for the
voltage is obtained.
CAUTION: Do not exceed the maximum allowable voltage input (1000V DC). Also,
never apply a voltage over the current input terminal (I) of the DMM.
Section
2
FUNCTION MATH
DISPLAY
DC I
AC I
Ω
4W
Period
dB
dBm
DC V AC V Ω2W Freq Cont Null Min/Max
HI
HI
LO
LO
I
V
Ω
Ω
4W Sense
Shift
Select DC V or AC V
AC or Dc Voltage
-
+
Figure 2. How to Measure Voltage

TAKING MEASUREMENTS
4
FUNCTION MATH
DISPLAY
DC I
AC I
Ω
4W
Period
dB
dBm
DC V AC V Ω2W Freq Cont Null Min/Max
HI
HI
LO
LO
I
V
Ω
Ω
4W Sense
Shift
First Shift, then Select
AC or DC
AC or DC Current
-
+
Figure 5. Probe/Meter Placement to
Measure Current Through Meter
+
A
Circuit
Under Test
DMM
_
I
How to Measure DC and AC
Current
To use the DMM as an ammeter, connect the leads in which the current flows to the current
(I) andLO terminals (Figure 4). To measure the current, either the DC I orAC I keymustbe
selected by pushing SHIFT and DC V or AC V button.
Next, connect the leads of the probes to the
circuit in series with the location of the
current in question (Figure 5). The current
(I) lead connects to the “+” (pos) part of
the circuit and the Lo to the “–“ (neg). If
these are reversed, a negative value for the
current is obtained.
CAUTION: Do not exceed the maximum allowable current input
(3A DC). Never apply a voltage over the current input terminal (I) of
the DMM. This will cause a large current to flow through the small
input resistor riand can damage the DMM.
Figure 4. How to Measure Current

TAKING MEASUREMENTS
5
How to Measure Resistance
To use the DMM for resistance measurements, connect the resistor to the terminals labeledHI
(V Ω)and LO, select the resistance measurement function by pushing the [Ω]button on the
front panel as shown below in Figure 6.
Then connect the leads of the probes to the circuit in
parallel with the resistance in question (Figure 7).
How to Measure Frequency
To use the DMM for frequency measurements, connect to the terminals labeledHI(VΩ)and
LO. Select the frequency measurement function by pushing the Freq button on the front
panel as shown below in Figure 8. The meter is connected in parallel the same as taking a
resistance measurement (Figure 7).
Figure 6. How to Measure Resistance
Figure 7
. Probe/Meter Placement to
Measure Resistance Across Resistor R
Hi
Ω
DMM
Lo
FUNCTION MATH
DISPLAY
DC I
AC I
Ω
4W
Period
dB
dBm
DC V AC V Ω
2W
Freq Cont Null
Min/Ma
x
HI
HI
LO
LO
I
V
Ω
Ω
4W
Shif
t
Select for Frequency
Measurements
Frequency
Figure 8. How to Measure Frequency
FUNCTION MATH
DISPLAY
DC I
AC I
Ω
4W
Period
dB
dBm
DC V AC V Ω2W Freq Cont Null Min/Max
HI
HI
LO
LO
I
V
Ω
Ω
4W Sense
Shift
Select for Resistive measurements
R

SUPPLEMENTAL INFORMATION
6
Troubleshooting
What if the meter will not turn on?
First make sure it’s plugged in; if this is the case get a TA for assistance, the
meter may have a blown fuse or need repair.
The meter is on, but is not taking any readings when it’s connected to the circuit.
Make sure to check that the probe inputs have been inserted in the proper configuration, for
this check back in the “Making Measurements, Section 2” (Notice: voltage and current are
different).
Next, check to make sure that the Front/Rear input selection button is not depressed (located
in the probe input panel to left of the “current (I)” input.
The probe inputs are correct, but when the meter is connected to the circuit the meter reads invalid values or does
not read at all.
Check that the meter is connected to the circuit in the correct orientation. It must be
connected in series for current readings and in parallel for voltage, frequency and resistance.
Check back in the “Making Measurements, Section 2” for more information.
Where to Find More Help
ØThe complete manual on the HP website:
http://www.tm.agilent.com/classes/MasterServlet?view=HomePage&language=eng&locale=
US
ØThe Lab Manual
ØLab TA
References
[1] “HP 34401A user’s manual,” [Online document], Feb. 1996, Available HTTP:
http://cp.tm.agilent.com/data/downloads/eng/tmo/manuals/
pdf/34401A_UsersGuide_English.pdf
Section
3